Dexter Laundry T-350 SWD Express User manual

8533-118-001 8/21

Dexter Commercial Vended Stack Washer Dryer

T-350 C4

Parts & Service Manual

Starting serial number

2

Indicates an imminently hazardous situation, which if

not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation, which if not

avoided could result in death or serious injury.

Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury. It may

also be used to alert against unsafe practices. Minor

burns, pinch points that result in bruises and minor

chemical irritation.

Indicates information or a company policy that relates

directly or indirectly to the safety of personnel or protec-

tion of property.

This is the user caution symbol. It indicates a condition

where damage to the equipment resulting in injury to

the operator could occur if operational procedures are

not followed. TO REDUCE THE RISK OF DAMAGE OR

INJURY, refer to accompanying documents; follow all

steps or procedures as instructed.

This is the electrical hazard symbol. It indicates that

there are DANGEROUS HIGH VOLTAGES PRESENT inside

the enclosure of this product. TO REDUCE THE RISK OF

FIRE OR ELECTRIC SHOCK, do not attempt to open the

enclosure or gain access to areas where you are not

instructed to do so. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL ONLY

Caution! There are sharp edges on various sheet metal

parts internal to the enclosure. Use safety consciousness

when placing or moving your hands while working in the

interior of this equipment.

Caution! To reduce the risk of damage to the Water Inlet

Valve, do not supply inlet water with a temperature that

exceeds 70˚ C.

Caution! To reduce the risk of re or explosion, do not

operate this equipment in any hazardous classied

(ATEX) environment.

Equipment Safety Warnings

Symbols and Terminology Used in this Equipment

Equipment Safety Warnings

Symbols and Terminology Used in this Equipment

Part # 8533-118-001 8/21

3

Equipment Safety Warnings

Symbols and Terminology Used in this Equipment

Warning! Do not operate equipment if door glass is

damaged in any way.

Warning! Keep clear of rotating parts.

Prohibited! Do not enter this equipment or space.

Prohibited! Do not step or stand on this equipment.

Prohibited! Do not operate without all guards and covers in

place.

Prohibited! Do not operate without all guards and covers in

place.

Prohibited! Do not wash clothing impregnated with

ammable liquids (petrochemical).

Prohibited! Do not allow children to play in or around

equipment.

Equipment Safety Warnings

Symbols and Terminology Used in this Equipment

Part # 8533-118-001 8/21

4

Indicates an imminently hazardous situation,

which if not avoided, will result in death or seri-

ous injury.

Indicates a potentially hazardous situation,

which if not avoided could result in death or

serious injury.

Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderate injury. It may also be used to alert

against unsafe practices. Minor burns, pinch

points that result in bruises and minor chemical

irritation.

Indicates information or a company policy that

relates directly or indirectly to the safety of per-

sonnel or protection of property.

This is the user caution symbol. It indicates a

condition where damage to the equipment re-

sulting in injury to the operator could occur if

operational procedures are not followed. TO RE-

DUCE THE RISK OF DAMAGE OR INJURY, refer

to accompanying documents; follow all steps or

procedures as instructed.

This is the electrical hazard symbol. It indicates

that there are DANGEROUS HIGH VOLTAGES

PRESENT inside the enclosure of this product.

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, do not attempt to open the enclosure or

gain access to areas where you are not instruct-

ed to do so. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL ONLY

Caution! To reduce the risk of re or explosion,

do not operate this equipment in any hazardous

classied (ATEX) environment.

Part # 8533-118-001 8/21

5

•All washers must be installed in accordance to all

applicable electrical, plumbing and all other local

codes.

•These installation and operation instructions are for

use by qualied personnel only. To avoid injury and

electrical shock, do not perform any servicing other

than that contained in the installation and operation

instructions, unless qualied.

Do not install washers in an explosive atmosphere.

•Care must be stressed with all foundation work to

ensure a stable unit installation, eliminating possi-

bilities of excessive vibration.

•Foundation must be level within 13 mm to ensure

proper washer operation.

Do not operate washer if door glass is damaged in

any way.

Do not wash clothing impregnated with ammable

liquids (petrochemical).

WARNING

Part # 8533-118-001 8/21

6

Children should be supervised to

ensure they do not operate or play

in or around equipment.

Keep all panels in place to protect against electrical

shock and injury and add rigidity to washer.

WARNING

This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities, or

lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a

person responsible for their safety.

A washer should not be allowed to operate if any of the following occur:

• Excessive high water level.

• Machine is not connected to a properly earthed circuit.

• Door does not remain securely locked during the entire cycle.

• Vibration or shaking from an inadequate mounting or foundation

Part # 8533-118-001 8/21

7

Warning! Do not operate equipment if door glass is

damaged in any way.

Warning! Keep clear of rotating parts.

Prohibited! Do not enter this equipment or space.

Prohibited! Do not step or stand on this equip-

ment.

Prohibited! Do not operate without all guards and

covers in place.

Prohibited! Do not operate without all guards and

covers in place.

Prohibited! Do not wash clothing impregnated

with ammable liquids (petrochemical).

Prohibited! Do not allow children to play in or

around equipment.

Part # 8533-118-001 8/21

8

Prohibited! Do not attempt to open, touch, or pro-

ceed before referring to the manual or unless quali-

ed.

Mandatory! Read all supporting documentation be-

fore operating or maintaining equipment.

Mandatory! Disconnect power before servicing

equipment.

Mandatory! Lock out and tag out before servicing

this equipment.

Mandatory! Disconnect water supply before servic-

ing equipment.

Mandatory! Children should be supervised to ensure

they do not operate equipment.

Part # 8533-118-001 8/21

9

Prohibited! Do not attempt to open, touch, or pro-

ceed before referring to the manual or unless quali-

ed.

Mandatory! Read all supporting documentation be-

fore operating or maintaining equipment.

Mandatory! Disconnect power before servicing

equipment.

Mandatory! Lock out and tag out before servicing

this equipment.

Mandatory! Disconnect water supply before servic-

ing equipment.

Mandatory! Children should be supervised to ensure

they do not operate equipment.

A machine should not be allowed to

operate if any of the following occur:

• Excessively high water level.

• Machine is not connected to a properly grounded

circuit.

• Loading door does not remain securely locked

during the entire cycle.

• Vibration or shaking from an inadequate mounting

or foundation.

Table of Contents

Section 1:

Specications, Mounting Dimensions

Specications..............................................14-15

Dimensions..................................................16-17

Section 2:

Installation & Operating Instructions

Washer Installation ........................................20

Electrical Connections & Fusing Requirements .21

Dryer Installation.................................................22

Dryer Electric, Gas and Venting.....................23-24

Washer Operating Instructions......................25-26

Emergency Stop Button .................................25

Dryer Operating Instructions..............................26

Section 3:

Washer and Dryer Programming Instructions

Rapid Advance Mode ...................................... 30

Washer Price Programming...........................32-33

Wash Cycle Programming ......................... 34-37

Dryer Programming.......................................46-59

Section 4:

Dryer Service,Troubleshooting and Schematics

Dryer Service Procedures..............................62-67

Dryer Control Fault Codes..............................71-72

Dryer Troubleshooting Tips ........................ 7 3 - 7 4

Dryer Schematics 60hz ............................. 78-79

......................................................100-101

Section 5:

Dryer Parts Data......................................81-103

Section 6:

50hz Gas Dryers

50hz Dryer Parts....................................106-109

50hz Dryer Schematics...........................111-112

Section 7:

Washer Service and Troubleshooting

Electronic Coin Drop Acceptor...........................114

Electronic Coin Drop Maintenance.............115-118

Detergent Dispenser .................................... 119

Dexter Safety

Guidelines

FOR SAFETY

1. Always shut o power and water

supply and also discharge capacitors

before servicing.

2. Do not overload the washer.

3. Do not attempt to open door if cylinder

is in motion or contains water.

4. Do not mechanically force or override

door lock in any way.

5. Do not bypass any safety devices of

this washer.

6. Do not use volatile or ammable

substances in or near this washer.

7. Keep all panels in place. They protect

against shock and injury and add

rigidity to the washer.

To activate your warranty, be sure to return

your red warranty form to the factory. Please

have serial number and model ready when

calling for assistance.

WARNING

These washers are equipped with devices and

features relating to their safe operation. To

avoid injury or electrical shock, do not perform

and service, unless qualied to do so.

Part # 8533-118-001 8/21

10

Optical Coin Drop Acceptor...............................120

Front Panel Removal ....................................120

Back Panel Removal .....................................120

Drain Valve Access ....................................... 120

Drain Valve Cleaning ....................................120

Vacuum Breaker/Air Gap ...............................122

Water Valves ...............................................122

Door Lock Assembly Operation ..................... 122

Adjustment for Door Lock Assembly ........122-123

Adjusting the Loading Door .......................... 124

Loading Door Removal .................................124

Loading Door Hinge Removal ........................ 124

Loading Door Disassembly ........................... 124

Loading Door Reassembly ............................125

Control Panel Name Plate Decal .................... 125

Name Plate Removal ....................................125

Re-Installation of Name Plate ........................125

Removal of the Washer Tub Assembly From the

Washer Frame .......................................125

Bearing Housing Water Seals .................126-128

Bolt Torque Chart .........................................128

Control Mounting Trough .............................. 129

Main Data Communication Cable ...................129

Circuit Breaker/Fuse .....................................129

Main Control Printed Circuit Board .................129

Controls Transformer....................................129

Main Relay Printed Circuit Board ................... 129

LED Printed Circuit Board Temperature & Start

Display Push Button ............................... 130

Emergency Stop Button & Switch Assembly...130

Power Connection Terminal Block .................130

Pressure Switch .....................................132-133

Delta Variable Frequency Drive .....................134

Delta VFD Motor Leads.................................134

Delta VFD Dynamic Braking

Resistors .....................................................134

Delta VFD Cooling Fan .................................134

Washer Trouble Shooting and F - Codes...135-146

Section 8:

Washer Electrical & Wiring Schematics

Start Circuit .................................................148

Fill Circuit ..............................................148-149

Wash Circuit ................................................149

Drain, Rinse 1, 2 & Final Rinse Circuit ............ 149

Extract Circuit .............................................. 149

Thermoactuator and Shake Out Circuit .......... 150

End of Cycle Circuit ......................................150

Motor Winding Resistances...............................150

Washer Electrical & Wiring Schematics 60hz

...................................................... 151-152

Section 9:

Washer Parts Data

C-Series Accessories ...................................154

Rear View Access Parts ..............................156

Cabinet and Front Panel Group .....................159

Cylinder, Seals & Bearings Parts .................160

Door Lock Parts ............................... 162 - 163

Loading Door Parts ....................................165

Drain Valve Group Parts .............................166

Water Inlet Parts ....................................... 167

Chassis and Drain Parts....................................168

Electrical Components ....................... 170 - 172

Labels..............................................................173

Coin Handling Group Parts .....................173 - 175

Section 10:

50hz Washer .................................................179

Section 12:

Maintenance Dryer...........................................186

Maintenance Washer....................................187

Part # 8533-118-001 8/21

11

Part # 8533-118-001 8/21

Section 1:

Washer and Dryer

Specications and

Mounting

12

Stacked Washer Dryer Models

Stacked Model

Designation

Washer \ Dryer

Model #

Electrical Spec: Circuit Breaker /

Running Amps / Wire Size/ Option

SC0350NE-17EC4X-

SWBCG-USA

9999-742-001

DCS020ND-15EC2X-

SWBCG-USA

9999-708-001

208-240/60/1, Single 2 Wire + Ground, United

States Quarter Optical Acceptor

WCS350XC-12EC4X-

SWBCS-USA

9999-741-001

208-240/60/1 or 3, Single 2 Wire + Ground, 3

Phase 3 Wire + Ground, United States Quarter

Optical Acceptor

SC0350NE-17EC4X-

SWBCS-USA

9999-742-002

DCS020ND-15EC2X-

SWBCS-USA

9999-708-003

208-240/60/1, Single 2 Wire + Ground, United

States Quarter Optical Acceptor

WCS350XC-12EC4X-

SWBCS-USA

9999-741-001

208-240/60/1 or 3, Single 2 Wire + Ground, 3

Phase 3 Wire + Ground, United States Quarter

Optical Acceptor

SC0350NE-17EC4X-

SWBCG-USX

9999-742-003

DCS020ND-15EC2X-

SWBCG-USX

9999-708-005

208-240/60/1, Single 2 Wire + Ground, United

States Quarter Optical Acceptor

WCS350XC-12EC4X-

SWBCS-USX

9999-741-002

208-240/60/1 or 3, Single 2 Wire + Ground, 3

Phase 3 Wire + Ground, United States Quarter

Optical Acceptor

SC0350NE-17EC4X-

SWBCS-USX

9999-742-004

DCS020ND-15EC2X-

SWBCS-USX

9999-708-007

208-240/60/1, Single 2 Wire + Ground, No Ac-

ceptor

WCS350XC-12EC4X-

SWBCS-USX

9999-741-002

208-240/60/1 or 3, Single 2 Wire + Ground, 3

Phase 3 Wire + Ground, No Acceptor

SC0350NE-17EC4X-

SWKCG-USA

9999-742-005

DCS020ND-15EC2X-

SWKCG-USA

9999-708-002

208-240/60/1, Single 2 Wire + Ground, United

States Quarter Optical Acceptor

WCS350XC-12EC4X-

SWKCS-USA

9999-741-003

208-240/60/1 or 3, Single 2 Wire + Ground, 3

Phase 3 Wire + Ground, United States Quarter

Optical Acceptor

SC0350NE-17EC4X-

SWKCS-USA

9999-742-006

DCS020ND-15EC2X-

SWKCS-USA

9999-708-004

208-240/60/1, Single 2 Wire + Ground, United

States Quarter Optical Acceptor

WCS350XC-12EC4X-

SWKCS-USA

9999-741-003

208-240/60/1 or 3, Single 2 Wire + Ground, 3

Phase 3 Wire + Ground, United States Quarter

Optical Acceptor

SC0350NE-17EC4X-

SWKCG-USX

9999-742-007

DCS020ND-15EC2X-

SWKCG-USX

9999-708-006

208-240/60/1, Single 2 Wire + Ground, No Ac-

ceptor

WCS350XC-12EC4X-

SWKCS-USX

9999-741-004

208-240/60/1 or 3, Single 2 Wire + Ground, 3

Phase 3 Wire + Ground, No Acceptor

SC0350NE-17EC4X-

SWKCS-USX

9999-742-008

DCS020ND-15EC2X-

SWKCS-USX

9999-708-008

208-240/60/1, Single 2 Wire + Ground, No Ac-

ceptor

WCS350XC-12EC4X-

SWKCS-USX

9999-741-004

208-240/60/1 or 3, Single 2 Wire + Ground, 3

Phase 3 Wire + Ground, No Acceptor

Part # 8533-118-001 8/21

13

Stacked Model

Designation

Washer \ Dryer

Model #

Electrical Spec: Circuit Breaker /

Running Amps / Wire Size/ Option

SC0350NE-39AC4X-

SWBCG-VRX

9999-742-009

DCS020ND-39AC2X-

SWBCG-VRX

9999-708-009

230/50/1, Single 2 Wire + Ground, No Acceptor

WCS350XC-39XC4X-

SWBCS-VRX

9999-741-005

230/50/1, Single 2 Wire + Ground, No Acceptor

SC0350NE-39AC4X-

SWBCS-VRX

9999-742-010

DCS020ND-39AC2X-

SWBCS-VRX

9999-708-011

230/50/1, Single 2 Wire + Ground, No Acceptor

WCS350XC-39XC4X-

SWBCS-VRX

9999-741-005

230/50/1, Single 2 Wire + Ground, No Acceptor

SN0350NE-17EP4X-

SWKCG-VRX

9999-742-011

DCS020ND-39AC2X-

SWKCG-VRX

9999-708-010

230/50/1, Single 2 Wire + Ground, No Acceptor

WCS350XC-39XC4X-

SWKCS-VRX

9999-741-006

230/50/1, Single 2 Wire + Ground, No Acceptor

SC0350NE-39AC4X-

SWKCS-VRX

9999-742-012

DCS020ND-39AC2X-

SWKCS-VRX

9999-708-012

230/50/1, Single 2 Wire + Ground, No Acceptor

WCS350XC-39XC4X-

SWKCS-VRX

9999-741-006

230/50/1, Single 2 Wire + Ground, No Acceptor

SC0350NE-39XC4Z-

SWBCG-VRX

9999-742-033

DCS020ND-39XC2Z-

SWBCG-VRX

9999-708-021

230/50/1, Single 2 Wire + Ground, No Acceptor

WCS350XC-39XC4Z-

SWBCS-VRX

9999-741-011

230/50/1, Single 2 Wire + Ground, No Acceptor

SC0350NE-39XC4Z-

SWBCS-VRX

9999-742-034

DCS020ND-39XC2Z-

SWBCS-VRX

9999-708-023

230/50/1, Single 2 Wire + Ground, No Acceptor

WCS350XC-39XC4Z-

SWBCS-VRX

9999-741-011

230/50/1, Single 2 Wire + Ground, No Acceptor

SC0350NE-39XC4Z-

SWKCG-VRX

9999-742-035

DCS020ND-39XC2Z-

SWKCG-VRX

9999-708-022

230/50/1, Single 2 Wire + Ground, No Acceptor

WCS350XC-39XC4Z-

SWKCS-VRX

9999-741-012

230/50/1, Single 2 Wire + Ground, No Acceptor

SC0350NE-39XC4Z-

SWKCS-VRX

9999-742-036

DCS020ND-39XC2Z-

SWKCS-VRX

9999-708-024

230/50/1, Single 2 Wire + Ground, No Acceptor

WCS350XC-39XC4Z-

SWKCS-VRX

9999-741-012

230/50/1, Single 2 Wire + Ground, No Acceptor

Part # 8533-118-001 8/21

14

Washer Specications:

Dry Weight Capacity 20 lbs. (9.1 kg)

Cylinder Diameter 21” (53.3 cm)

Cylinder Depth 13.5” (34.3 cm)

Cylinder Volume 2.7 cu ft. (76.5 l)

Floor to Door Bottom 14.875” (37.8 cm)

Door Opening 12.25” (31.1 cm)

Speeds G-Force (RPM)

High Extract Speed 200 G 579 RPM

Intermed. Extract Speed 60 G 449 RPM

Washing Speed 0.9G 55 RPM

Motor Size 1 HP 0.75 kW

Electrical

Electrical Phase Single or Three

Electrical Voltage (60 Hz) 208-240

Electrical Running (Amps) 6.2 amp

Circuit Protection (Amps) 15 amp

Electrical Wire Size 12 gauge

Electrical Service (Single) 2 wire + ground

Electrical Service (Three) 3 wire + ground

Water

Water Inlet Size 3/4” (19mm)

Flow Rate (per min) 9 gal (34.1 L)

Pressure (min/max) 30-120 psi (207-827 Kpa)

Drain Diameter (O.D.) 2.25” (5.7 cm)

Floor to Center of Drain 5.875” (14.9 cm)

Installation Recommendations

Clearance Between Machines 1/2 (min) (1.31 cm)

Clearance Behind Machines 24” (min) (61.0 cm)

Concete Thickness 6” (min) (15.24 cm)

Net Weight 800 lbs. (362.9 kg)

Shipping Weight 840 lbs. (381.0 kg)

Approvals** UL/CSA

Cabinet Dimensions

Height - in (cm) 74.75” (189.9 cm)

Width - in (cm) 27.0” (68.6 cm)

Depth - in (cm) 44.625” (113.7 cm)

Part # 8533-118-001 8/21

15

8514-280-001 REV B PAGE 3

20 lb. Commercial Dryer: T-20 SWD

DCS020N_-15_C_X (60 Hz), DCS020N_-39_C_X (50 Hz)

Cabinet Height 34 3/4” 883 mm.

(Assumes minimum leveling leg adjustment)

Cabinet Width 27” 686 mm.

Overall Depth 44 5/8” 1133 mm.

Floor to Bottom of Door 8 1/2” 215 mm.

Door Opening 18 1/8” 460 mm.

Dry Wt. Capacity 20 lbs. 9.1 kg.

Cylinder Diameter 25 1/2” 647 mm.

Cylinder Depth 24” 609 mm.

Cylinder Volume 7.0 cu. ft. 198.2 liters

Lint Screen Area 285 sq. in. 1839 sq. cm.

Gas Input (60 hz) 56,000 Btu/hr 16.4 kW

Gas Input (50 hz) 47,000 Btu/hr 13.8 kW

Gas Supply Connection 1/2” 12.7 mm.

Natural Burner Manifold

(60 hz Water Column) 3.5” 88.9 mm

(50 hz Water Column) 3.5” 88.9 mm

L.P. Supply (Water Column) 11.5- 13.5” 292 mm- 343 mm

L.P. Burner Manifold Pressure

(60 hz Water Column) 11” 279 mm

(50 hz Water Column) 11” 279 mm

Exhaust Size 6” 152 mm.

Make-up Air 100 sq. in. 645 sq. cm.

Example: 100 sq. in = 10 in. long X 10 in. wide

Motor Size (50 or 60 Hz) 1/3 H.P. .248 kW

Airflow (60 hz) 370 CFM 10.5 m^3/min

Airflow (50 hz) 300 CFM 8.5 m^3/min

Electrical Specifications – 208-240/60/1

Voltage/Hz/Phase 208-240V/60Hz/1Phase

Running Amps 1.9

Circuit Protection Amps 15

Wire Size 12 gauge

Electrical Service 2 wire + ground

Electrical Specifications – 120/60/1

Voltage/Hz/Phase 120V/60Hz/1Phase

Running Amps 3.9

Circuit Protection Amps 15

Wire Size 12 gauge

Electrical Service 2 wire + ground

Electrical Specifications – 220-240/50/1

Voltage/Hz/Phase 220-240V/50Hz/1Phase

Running Amps 3.2

Circuit Protection Amps 15

Wire Size 3.5 mm2

Electrical Service 2 wire + ground

Shipping Weight 350 lbs. 159 kg.

Net Weight 320 lbs. 145 kg.

Clearance Behind Machines (min.) 18” 457 mm.

Part # 8533-118-001 8/21

16

Machine Dimensions:

Part # 8533-118-001 8/21

17

SWD Mounting Pad Dimensions



Part # 8533-118-001 8/21

18 Part # 8533-118-001 8/21

Notes

19

Part # 8533-118-001 8/21

Section 2:

Washer and Dryer

Installation

& Operating

Instructions

20

Washer Installation

All washers must be installed in accordance with all local, state and national building,

electrical, and plumbing codes in eect in the area.

Foundation Requirements

The washer must be securely bolted to a substantial concrete oor, or mounted upon a suitable base

which is securely bolted and machine grouted to a substantial concrete oor. Care must be stressed with

all foundation work to insure a stable unit, eliminating vibration. All installations must be made on sound

concrete oors 6” or thicker. Anchor bolts must be of a quality grade and at least imbedded at minimum

of 5” in length and minimum 5/8” diameter.

Mounting

A concrete pad or steel base which elevates the machine 4 to 6 inches above the oor level. To provide

easy access to the loading door, it is recommended to allow a minimum of 18” of clearance behind the

rear of the machine for service as is shown. SIX (6) bolts are required to mount the washer to the steel

base or concrete pad. Grouting where base or machine makes contact with concrete is REQUIRED to

achieve 100% surface contact and for warranty to be honored.

NOTE: Premanufactured bases are available from DEXTER factory (see sales dept.)

Mounting Bolts

The following pages illustrate the mounting dimensions for the machine and also show a typical concrete

pad arrangement.

NOTE: Mounting bolts should be checked frequently to insure that they remain tight.

The machine should be checked with a spinning load to be sure there is no unusual

vibration or movement between the machine and the base or oor.

Proper Machine Grout Required Installation

Machine grout must be installed between base (if used) and concrete oor on all side rails and crossmem-

bers. If using a base you must grout between base top and machine frame and all side rails and cross-

members.

Plumbing

Water supply hoses are furnished with each machine. The threaded connections on the hoses are

standard garden hose type thread. Separate hot and cold water lines with shut o valves or faucets for

inlet hose connections must be provided, maintaining 30 to 120 p.s.i. water ow pressure. Maximum water

temperature is 180 degrees.

Drain

The drain outlet tube at the rear of the machine is 3” in outside diameter. Adequate fall for this gravity

drain must be maintained for proper drainage.

Protective Film

The machine may have protective adhesive lm on the front escutcheon area and the front and side

stainless steel panels. The lm may be peeled o before putting the machine into service.

Electrical

Dexter single/three-phase 208-240VAC 60 Hz washing machines are intended to be permanently installed

appliances. No power cord is provided. The machine should be connected to an individual branch circuit

not shared by lighting or other equipment. The connection should be sheathed in liquid tight exible

conduit, or equivalent, with conductors of the proper size and insulation. A qualied technician should

make such connections in accordance with the wiring diagram.

Each unit should be connected to an individual branch circuit not shared by lighting or other equipment.

Conductors of the proper size and insulation (suggested size below) should be used.

Part # 8533-118-001 8/21

Page is loading ...

Dexter Laundry T-350 SWD Express User manual

Dexter Laundry T-350 SWD Express User manual

Related papers

Other documents