2. Home
  3. Lighting
  4. Stroboscopes & disco lights
  5. CLS
  6. Ruby Bracket Modular

CLS Ruby Bracket Modular, Ruby Bracket Modular ColourFlow Owner's manual

  • Hello, I'm your chat assistant. I have reviewed the user manual for the CLS RUBY BRACKET MODULAR SERIES and ready to answer your questions. This document contains detailed information on the device's technical specifications, installation, configuration, and key features, including dimming options and lens choices.
  • What type of power supply is required?
    What is the weight of the device?
    What are the available lens options?
    What are the dimming control options?
www.cls-led.com www.cls-led.com
CeilingWallFloor3700 gr 50.000 h19º 49º 63ºIP20 3000K
CRI>80
2700K
CRI>80
2700K
CRI>92
4000K
CRI>80
4000K
CRI>92
RGBW
W: 4000K
1800K
4000K
2700K
5700K
DRIVER
INCLUDED
DRIVER
INTERNAL
80 ~ 264
VAC
Max.
110 Watt
3000K
CRI>92
CLS
DYNAMIC
COLOUR
COB
2
CLS RUBY BRACKET MODULAR SERIESCLS RUBY BRACKET MODULAR SERIES
Manual V1.1 - March 2021
INDEX
Index 2
Safety information 2
Content 2
Technical 3
Specifications 3
Installation 4
Clamp Mounting 5
Reflector replacement 6
Status display 8
Configuration 8
Menu description 8
Page 1: DMX addressing 9
Page 2: Static behaviour 9
Page 3: Soft dim option 9
Page 4: Master control configuration 9
Page 5: Dim curve used 9
Page 6: Output control 10
Page 7: Resolution 10
Page 8-11: Patch 10
Page 12-15: Static value 10
Page 16-19: Current setting configuration 11
Page 20: Record static value 11
Page 21: Firmware vesion 11
Page 22: Testloop 11
Page 23: Store configuration 11
Page 24: Cancel configuration 11
List of Symbols 12
www.cls-led.com www.cls-led.com
3 4
CONTENT
Ambiance
Max. 40º
Block access
below the work
area when
maintaining
the unit
Use a source
of AC power
that complies to
local electrical
codes
Disconnect the
power supply
before installing
or maintaining
Don’t install in
a flammable
or explosive
area
Warning!
Some surfaces
can be hot
Do not stare
into the LED
Don’t modify
or install
genuine parts
on this product
Qualified
technician
Make sure all
connectors are
connected
properly
SAFETY INFORMATION
2021 CLS-LED BV. All rights reserved. Information subject to change without notice, CLS-LED BV and all aliated companies disclaim
liability for injury, damage direct or indirect loss, consequential or economic loss or any other loss occasioned by the use of, inability to
use or reliance on the information contained in this manual. No part of this manual may be reproduced, in any form or by any means,
without permission in writing from CLS-LED BV. Other legal information can be found in our General conditions, found on the back of
your CLS-LED BV invoice, inside the CLS catalogue or on our website www.cls-led.com/General-Terms.pdf
Tools M10
TECHNICAL
SPECIFICATIONS
LED: 1 x Citizen or CLS DCC
Available colours: CRI>80: 2700K, 3000K, 4000K
CRI>92: 2700K, 3000K, 4000K
Colour changing: RGBW (W: 4000K)
Tunable White: 1800K-4000K or 2700K-5700K
Lenses: 19º, 49º, 63º
Power supply: 80 ~ 264 VAC
Power consumption: 9 serie: max. 110 Watt
Connection: Power: Neutrik Powercon TRUE
DMX: XLR3
Housing: Anodised aluminium black or white coated
Weight: 3700 gr
IP value: IP20
Measurements: 417 x 163,7 x 140 mm (hxbxø)
Ambient temperature: -10º C till +40º C
CeilingWallFloor3700 gr 50.000 h19º 49º 63ºIP20 3000K
CRI>80
2700K
CRI>80
2700K
CRI>92
4000K
CRI>80
4000K
CRI>92
RGBW
W: 4000K
1800K
4000K
2700K
5700K
DRIVER
INCLUDED
DRIVER
INTERNAL
80 ~ 264
VAC
Max.
110 Watt
3000K
CRI>92
CLS
DYNAMIC
COLOUR
COB
1 x Neutrik Powercon TRUE cable
417 mm
322 mm
Ø140 mm
158 mm
ø 140 mm
163,70 mm
ø 10 mm
417 mm 322 mm
Ø140 mm
158 mm
ø 140 mm
163,70 mm
ø 10 mm
417 mm 322 mm
Ø140 mm
158 mm
ø 140 mm
163,70 mm
ø 10 mm
Backplate
XLR3Display
Powercon
TRUE
www.cls-led.com www.cls-led.com
65
2
Option 2: Rigging
Max 6 Ruby’s in one line (C-16 fuse)
Option 1: Installation
XLR3
DMX
controller
Neutrik
Powercon TRUE
Position
indicator
INSTALLATION
12
3 4
56
Make sure
the indicated
holes falls over
the clips
78
910
See next page for step 7
REFLECTOR REPLACEMENT
www.cls-led.com www.cls-led.com
7 8
12
3 4
56
Make sure
the indicated
holes falls over
the clips
78
910
See next page for step 7
REFLECTOR REPLACEMENT STATUS DISPLAY
CONFIGURATION
Menu description
When the Ruby is powered the status
display is shown with the DMX address.
To enter the menu press and hold the
menu button for 3 seconds. The Ruby
will enter menu interface on page 1. The
menu interface holds different pages.
Use the up and down button to scroll
through the pages. To select the page
press the menu button. In each page
the settings can be adjusted. To leave a
page press the menu button again.
The Ruby must be configured to fit the application it is used for.
To make configuration easy the Ruby has a user friendly menu interface.
Page 1:
Status display
Page 2:
Page 3:
Page 4:
Page 5:
Page 6:
Page 7:
Page 8:
Page 9:
Page 10:
Page 11:
Page 12:
Page 13:
Page 14:
Page 15:
Page 16:
Page 17:
Page 18:
Page 19:
Page 20:
Page 21:
Page 22:
Page 23:
Page 24:
Hold Menu button for 3
seconds to enter menu
Hold Menu button for 3
seconds to store or cancel
Use Up/Down
button
The Ruby has a display which is used to interface with the user. When the Ruby is powered the DMX
address is showed. When DMX is active the DMX status dot is on. With no DMX signal the dot is flashing.
By pressing the menu button you can scroll through the different status pages.
The status pages dots will indicate which page is displayed. The status pages will show the output value of
the outputs 1-4 from 0 (min) to 255 (max).
DMX status
Up Menu Down
Page 4: output status Chn. 4
Page 1: output status Chn. 1
Page 2: output status Chn. 2
Page 3: output status Chn. 3
www.cls-led.com www.cls-led.com
9 10
Page 1: DMX addressing
In this page you can adjust the DMX address
of the LDC-41. Use the up and down button
to adjust the value. Hold down the up or down
button to scroll fast. When DMX address is
selected press the menu button to return to
the main menu.
Default DMX address: 1
-Page 1:
Use Up/Down
button
Press the Menu button
to return
Page 2: Static behavior
Static behavior when no DMX is connected.
“HLd” = Hold last data
“oFF” = Output off
“LSv” = Load static values
Page 3: Soft dim option
“oFF” = softdim off
“on” = softdim on
Page 4: Master control configuration
Master used for dim channel;
“oFF” = Master function off
“Frt” = Master is first channel
“LSt” = Master is last channel
Page 5: Dim curve used
“Lin” = lineair
“LoG” = logarithmic
Page 2:
Use Up/Down
button
Press the Menu button
to return
-Page 3:
Use Up/Down
button
Press the Menu button
to return
Page 4:
Use Up/Down
button
Press the Menu button
to return
- Page 5:
Use Up/Down
button
Press the Menu button
to return
Page 6: Output control
“hYb” = Hybrid
“aNa” = Analog (Constant Current Reduction)
“DiG” = Digital (Stochastic Signal Density Modulation)
Output control dimming charts
Page 7: Resolution
Control resolution 8 Bit.
1 DMX channel per output.
0% 100%
SSDM
0% 100%
Hybrid 0% 5% 100%
CCR
Page 8-11: Patch
To adjust the Patch Value of an output channel
enter the corresponding page and change the
value. The Patch value can be adjusted from 0
– 4. To return to the main menu press the menu
button.
- Page X: X
Use Up/Down
button
Press the Menu button
to return
Page 7:
Press the Menu button
to enter or return
Page 6:
Use Up/Down
button
Press the Menu button
to return
Page 12-15: Static Value
To adjust the Static Value of an output channel
enter the corresponding page and change the
value. The Static value can be adjusted from 0 –
255. To return to the main menu press the menu
button.
-Page X: X
Use Up/Down
button
Press the Menu button
to return
www.cls-led.com www.cls-led.com
11 12
Page 16-19: Current Setting configuration
To adjust the current of an output channel enter
the corresponding page and change the value. The
current can be adjusted from 350 – 1000mA in
steps of 50mA. To return to the main menu press
the menu button.
-
Page X: X
Use Up/Down
button
Press the Menu button
to return
..
Page 22: Test loop
Entering this page will result in a test loop on the
outputs of the LDC-41. This enables the user to
test the connections without the need of an DMX
controller. To end the test sequence and return to
the main menu press the menu button.
Page 20: Record Static value
"YES" = Will copy the DMX values
"No" = Return without recording
Page 21: Firmware version
Current firmware version on the LDC-41.
Test sequencePage 22:
Press the Menu button
to enter or return
X
Page 21:
Press the Menu button
to enter or return
-
Page 20:
Use Up/Down
button
Press the Menu button
to return
Page 23: Store configuration
After all changes are made the setting need to be
stored before they become active. To store the
settings go to the store page and press and hold
the menu button for 3 seconds. The settings are
stored and you will return to the status display.
Status display
Page 23:
Hold the Menu button
for 3 seconds to store
Page 24: Cancel configuration
When you have made changes but you don’t want
to store them you can cancel the settings. Go to
the cancel page and press and hold the menu
button for 3 seconds. The settings are not stored
and you will return to the status display.
Default Current configuration: 700mA for each channel
Status displayPage 24:
Hold the Menu button
for 3 seconds to cancel
LIST OF SYMBOLS
Multiple connection
Daisychain connectivity
Installation depth
In centimeters
Swivel
Fixture is horizontally rotatable,
indicated in degrees
Swivel
Fixture is vertically rotatable,
indicated in degrees
Installation size
In centimeters
Application area
Indoor or outdoor
Application area
Floor, wall or ceiling
Protection class
One, two or three
Cable length
Maximum cable attached
to the fixture in centimeters
Lifespan
Of the light source in hours
Driver
Inclusive or exclusive
Internal or external
Pressure
Maximum pressure on the
fixture in kg/cm2
Weight
In grams/kilograms
Curve
Minimal bending curve
in centimeters
LED pitch
Pitch between the LEDs
in millimeters
Power supply
In VDC, VAC or milliAmpere
Power consumption
In VA or Watt
IP value
Ingress Protection classifies the
degrees of protection provided against
the intrusion of the product
Cutting length
Indicated by the cutting
marks
LEDs
Kind of LED used in the
fixture
Lenses
Availble lenses,
indicated in degrees
Performance Zoom
Adjustable beam angle
Plug & play
Easy connection using the
SmartConnect system
White colour temperature
In dierent Kelvin values;
Cold white, neutral white, warm
white or extra warm white
Colour
Available colours;
Amber, blue, red or green
Colour changing
RGB, RGB-W, RGB-A,
AWB or Tunable White
DMX input
Fixture works on DMX512
protocol or Wireless DMX
Magno dimming
Accurate dimming from
100 - 1% by using a magnet
Dynamic Control
Dynamic Power Control or
Dynamic Temperature Control
Combined product
Compose your own fixture
Warranty
3 or 5 years warranty on
the product
Energy label
Conformité Européenne
CE marking for free marketability
of industrial goods within the EU
r
h
ø w d
Dimmable
1-10 Volt, Phase, individual,
DMX dimmable or DALI
DRIVER
INCLUDED
DRIVER
EXTERNAL
Retail & Food LED modules
Clothing, furniture, kitchens, jewellery,
shoes, bread, meat, fish and
vegetables & fruit.
Lightsource
Equipped with a CLS, Citizen or a Xicato
LED module
Bluetooth controlled
By Casambi
PWM dimming
Traditional PWM dimming, DMX analog
or DMX Hybrid dim
CLS
DYNAMIC
COLOUR
COB
/