PT PT600R Isolated RS232 Module Owner's manual

Type
Owner's manual

PT PT600R Isolated RS232 Module

The PT PT600R Isolated RS232 Module is a device that allows you to connect your PT600R indicator to other devices using an RS-232 serial connection. This can be useful for a variety of purposes, such as sending data from the indicator to a computer or printer, or controlling the indicator from a remote location.

The module has two RS-232 ports, one of which is isolated from the indicator and the other which is not. This allows you to connect to both isolated and non-isolated devices. The module also supports a variety of baud rates, parity bits, data bits, and stop bits, so you can configure it to work with most RS-232 devices.

PT PT600R Isolated RS232 Module

The PT PT600R Isolated RS232 Module is a device that allows you to connect your PT600R indicator to other devices using an RS-232 serial connection. This can be useful for a variety of purposes, such as sending data from the indicator to a computer or printer, or controlling the indicator from a remote location.

The module has two RS-232 ports, one of which is isolated from the indicator and the other which is not. This allows you to connect to both isolated and non-isolated devices. The module also supports a variety of baud rates, parity bits, data bits, and stop bits, so you can configure it to work with most RS-232 devices.

Manual M4201 RS232/RS232 Communications Module for PT600R
Product Support.
Module Description:
General 1 x isolated duplex RS-232 with DTR
1 x isolated TX-only RS-232
Isolation >500V from indicator to module
Power Supply Internal
Baud rate12400, 4800, 9600, 19200, 38400, 57600
Parity bit1None, Even, Odd
Data bits17, 8
Stop Bits11, 2
DTR1OFF, ON
Note 1: Instrument may not support all options.
Module Connections: Interface Diagram: Example Use:
PT Limited www.pt-global.com Page 1 of 2. Rev.1 2005-10-03 sme.
Manual M4201 RS232/RS232 Communications Module for PT600R
Product Support.
M4201 SETUP
The indicator should be switched OFF before installing or removing this device.
Modules are configured using the indicator setup. Setup can be done via the indicator keypad or the viewer
program. See the indicator Quick Start (P28) or Reference manuals for detailed setup information. An
overview of setup for the PT600R is given below.
The indicator provides configuration checking capabilities for the M4201. This is found in the H.WARE setup
menu. See the indicator Quick Start or Reference manuals.
PT600R SOFTWARE SETUP
This module is configured as serial port 2 on the PT600R indicator.
Network
(i) Setup. . . . SER.NET. . . . (Refer to quick start manual for settings)
Automatic Output
(i) Setup. . . . SER.AUT . . . . (Refer to quick start manual for settings)
Print
(i) Setup. . . . PRINT. . . . . . . (Refer to quick start manual for settings)
Port Configuration (i.e. Baud, etc)
(i) Setup. . . . H.WARE. . . . . SER2.HW. . . . (Refer to quick start manual for settings)
M4201 TROUBLESHOOTING
The M4201 has 4 annunciators which help with troubleshooting. These annunciators are shown as yellow on
the Module Connections figure above.
Problem Possible solutions
Receive not working.
M4201 receive annunciator not lit.
Check wiring.
Receive not working.
M4201 receive annunciator lit.
Check indicator setup (H.WARE:ALLOC).
Transmit not working.
M4201 transmit annunciator not lit.
Check indicator setup (H.WARE:ALLOC).
When printing: Check DTR annunciator and indicator
setup.
Transmit not working.
M4201 transmit annunciator lit.
Check wiring.
PT Limited www.pt-global.com Page 2 of 2. Rev.1 2005-10-03 sme.
  • Page 1 1
  • Page 2 2

PT PT600R Isolated RS232 Module Owner's manual

Type
Owner's manual

PT PT600R Isolated RS232 Module

The PT PT600R Isolated RS232 Module is a device that allows you to connect your PT600R indicator to other devices using an RS-232 serial connection. This can be useful for a variety of purposes, such as sending data from the indicator to a computer or printer, or controlling the indicator from a remote location.

The module has two RS-232 ports, one of which is isolated from the indicator and the other which is not. This allows you to connect to both isolated and non-isolated devices. The module also supports a variety of baud rates, parity bits, data bits, and stop bits, so you can configure it to work with most RS-232 devices.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI