Lefroy Brooks RL 1236 Installation & Servicing Guide

Brand: Lefroy Brooks

Model: RL 1236

Type: Installation & Servicing Guide

This manual is also suitable for

Sorry, I do not have information about Lefroy Brooks RL 1236 in the context. Therefore, I am unable to generate a response to your request.

1327 / 1328 / 1329 / 1370 / 1377 / 1381 / 1382

1383 / 1384 / 2140 / 8610

WASTES AND OVERFLOWS

INSTALLATION GUIDE

IMPORTANT INFORMATION

Professional installation

We recommend that our products are ﬁtted by

a fully qualiﬁed professional plumber. They should

be installed correctly and in accordance with all

local water regulations. All products should be

accessible for routine servicing.

Water quality

In hard water areas, a suitable water treatment

system should be provided to prevent limescale

deposits (calcium deposits) which may eect the

long term exterior ﬁnish. Exterior surfaces should

be gently wiped with a dry soft cloth after use to

minimise water stains and limescale deposits.

General installation details

Basin wastes have G 1¼" threaded tails and Bath

wastes have G 1½" threaded tails.

Mounting holes

Pre-formed holes in chinaware basins and baths

are usually made to a standard size to enable the

ﬁtting of wastes.

For custom made basins and baths the waste hole

sizes should be:

Basin – 44mm to 46mm

Bath – 50mm to 52mm

(For material thickness please refer to the

dimensional drawings).

28mm

max. 35mm

310mm

Ø60mm

Ø38mm

LB 1327 – Basin waste kit with brass plug & oval chain

33mm min.

63mm max.

88mm

Ø65mm

48mm

A/F hex

G 1¼

Ø42mm

DIMENSIONS

Not to scale

Ø60mm

G 1¼

Ø42mm

LB 1328 – Slotted click-up basin waste

27mm

Ø38mm

11mm open

88mm

34mm min.

63mm max.

12mm

19mm

Ø60mm

G 1¼

Ø42mm

LB 1329 – Un-slotted click-up basin waste

Ø38mm

11mm open

88mm

34mm min.

63mm max.

DIMENSIONS

Not to scale

G 1¼

Ø42mm

Ø45mm

40mm max.

326mm

58mm x 13mm

Ø60mm

Ø38mm

LB 2140 – Basin waste kit with centre hole cover plate

33mm min.

63mm max.

88mm

Ø65mm

48mm

A/F hex

DIMENSIONS

Not to scale

Ø50mm

1383 – Pop-up waste kit & assembly

320mm max.

36mm max.

190mm max.

50mm max.

G 1¼

Ø42mm

DIMENSIONS

Not to scale

500mm long

ﬂexible hose

600mm

Ø44mm

Ø60mm

19mm

6mm max

Ø70mm

12mm max

76mm

G 1½

(Ø48mm)

LB 1370 – Waste kit with brass overflow, plug & oval chain

DIMENSIONS

Not to scale

Ø70mm

G 1½

Ø48mm

46mm max.

51mm

454mm max.

(EXT models -

680mm max.)

Ø26mm

660mm

Ø44mm

Ø66mm

7mm

45mm

max.

39mm

LB 1382 & EXT-LB 1382 – Exposed bath waste with brass overflow pipe for free standing bath

222mm max. (EXT models - 313mm max.)

DIMENSIONS

Not to scale

LB 1377 – Waste kit with stowaway brass plug & oval chain

550mm long

ﬂexible hose

660mm

Ø44mm

Ø70mm

58mm

36mm max.

G 1½

(Ø48mm)

Ø66mm

30mm

max.

DIMENSIONS

Not to scale

LB 1384 – Belfast sink slotted waste with long chain

G 1½

(Ø48mm)

88mm

26mm min

60mm max

Ø86mm

Ø42mm

640mm

18mm

Ø4mm pilot

10 11

DIMENSIONS

Not to scale

LB 1381 – Easy clean shower waste with removable top

Ø72mm

Ø44mm

42mm

19mm max

52mm

A/F Hex

G 1½

(Ø48mm)

DIMENSIONS

Not to scale

Control rod link

Control rod

Ball joint retainer

Ball joint washer

Body

Rubber seal

Basin

Foam seal

Plug housing

Plug

Adjustment screw

Pop-up rod

Deck flange

O ring

Basin

Washer

Nut

Flange tail pipe

POP-UP WASTE INSTALLATION

1383 – Shown with classic rod. The same procedure applies to all rods

1 Locate the deck ﬂange ensuring that the O ring

is in place on the underside.

2 Pass the ﬂange tail pipe through the deck

ﬂange and secure using the washer and nut.

3 Insert the pop-up waste lever into the deck

ﬂange.

4 Assemble the pop-up waste to the basin with

the foam seal on top of the mounting surface

and the rubber seal below. The wide diameter

of the rubber seal sits on top of the waste

body. Tighten by hand.

5 Place the control rod link onto the rod of the

pop-up waste lever, then feed the control rod

through. Locate the short end of the control

rod, the one with the ball, into the waste and

secure by screwing the ball joint retainer in

place. Do not over tighten.

6 Gently clamp the control rod link to the

pop-up waste lever rod. Test the operation

of the pop-up waste and if satisfactory fully

tighten the control rod link to the pop-up

waste lever rod. If not satisfactory then

make adjustments to the control rod link as

required. If the operation is sti simply loosen

the ball joint retainer as required.

7 Connect the ﬂexible hoses to the basin mixer.

8 Connect the hot and cold water supplies to

the bottom of the appropriate ﬂexible hoses.

Turn on the water supplies and check for

leaks. Check the operation of the basin mixer.

Foam washer

Rubber seal

LB 1327 / LB 1328 / LB 1329

LB 1381 / LB 1384 / LB 2140

LB 1370 LB 1377 / LB 1382

Rubber seal

Sealing

compound Securing screw

(Tail secured) (Tail secured) (Screw secured)

Tail secured design

1 Ensure that the sealing face under basin/bath

is ﬂat and clean before ﬁtting the waste.

2 Locate the waste into the hole in the basin/

bath. To ensure a water tight seal when

ﬁtting the waste a foam washer or sealing

compound must be used between the waste

and the basin/bath.

3 On the underside of the basin/bath locate

the rubber seal onto the waste.

4 On the underside of the basin/bath locate

the large nut onto the threaded tail of the

waste. Tighten to secure the waste, but do

not over tighten.

5 Remove any excess sealant or foam washer

from inside the basin/bath.

WASTE INSTALLATION

Lefroy Brooks have three waste designs. These are:

• Tail secured wastes that are secured with a nut.

• Tail secured wastes that are secured with a nut and incorporate an overﬂow connection.

• Screw secured wastes that have a strainer plate secured to the waste by a central slotted screw.

These incorporate an overﬂow connection.

Installation is slightly dierent for each design.

Screw secured design

1 Ensure that the sealing face under basin/bath

is ﬂat and clean before ﬁtting the waste.

2 Locate the strainer plate into the hole in the

basin/bath. To ensure a water tight seal when

ﬁtting the strainer plate a foam washer or

sealing compound must be used between the

waste and the basin/bath.

3 Locate the rubber seal on top of the waste.

4 On the underside of the basin/bath locate the

the waste.

5 Place the screw through the centre hole in

the strainer plate and screw into the waste.

Tighten the screw to secure.

6 Remove any excess sealant or foam washer

from inside the basin/bath.

Rubber seal

(Tail secured) (Screw secured)

LB 1370 LB 1377 / LB 1382

Rubber seal

Clear silicon sealant Clear silicon sealant

Bath Bath

OVERFLOW INSTALLATION

Lefroy Brooks have two designs of overﬂow. These are:

• Tail secured overﬂows that are secured with a threaded cover.

• Screw secured overﬂows that have a cover plate secured to the overﬂow by a central slotted screw.

Installation is slightly dierent for each design.

Tail secured design

1 Ensure that the sealing face at the front and

rear of the bath is ﬂat and clean before ﬁtting

the overﬂow.

2 Ensure that the rubber seal is in place then

locate the overﬂow through the hole in the

bath. To ensure a water tight seal when

ﬁtting the overﬂow run a bead of clear silicon

sealant around the hole in the bath.

3 Locate and screw the cover onto the

threaded tail of the overﬂow. Tighten the

cover ensuring that the chain retainer is level

and the chain hangs vertically.

4 Remove any excess sealant from inside the

bath.

Screw secured design

1 Ensure that the sealing face at the front and

rear of the bath is ﬂat and clean before ﬁtting

the overﬂow.

2 Ensure that the rubber seal is in place then

locate the overﬂow to the rear of the hole in

the bath.

3 To ensure a water tight seal when ﬁtting the

cover plate run a bead of clear silicon sealant

around the hole in the bath.

4 Locate the cover plate and screw.

5 Tighten the screw to secure the cover plate

ensuring that the chain retainer is level and the

chain hangs vertically.

6 Remove any excess sealant from inside the

bath.

FLEXIBLE OVERFLOW HOSE INSTALLATION

Under normal circumstances there is no requirement for sealant to be used on the joints of the overﬂow

ﬂexible hose. Water only ﬂows through the ﬂexible hose when the basin/bath overﬂows. When water does

ﬂow through the hose it is free ﬂowing and not pressurised. Sealant can however be used if you prefer.

The overﬂow hose is designed to be pushed onto the overﬂow connections and be self supporting.

Ø80mm 33mm

52mm

Ø47mm

LB 8610 GRATED OVERFLOW COVER INSTALLATION

The grated overﬂow cover is designed for use with LB 1377 & LB 1382 bath wastes only.

Replacing an existing overﬂow

1 Remove the centre screw from the existing

overﬂow.

2 Remove the overﬂow cover plate from the

existing overﬂow.

3 Carefully remove any silicon sealant.

4 To ensure a water tight seal when ﬁtting the

grated overﬂow run a bead of clear silicon

sealant around the hole in the bath.

5 Locate the grated overﬂow and screw.

6 Place a 2.5mm diameter rod or small

screwdriver through the hole in the end of

the screw to tighten and secure the grated

overﬂow.

7 Remove any excess sealant from inside the

bath.

Whilst every effort is made to ensure the accuracy of these, they are subject to change without

notice as part of the company’s product development process. The use of trademarks, product design

and artwork is subject to licence or agreement with LBIP Ltd. The design registrations, trademark registrations

and copyrights are protected by law and the use or reproduction outside the terms of an agreement is prohibited.

The right to modify designs and dimensions is reserved. LBIP Ltd is a member of ACID (Anti Copying in Design). E&OE

CONTRACT ENQUIRIES

+44 (0)1992 708 316

info@lefroybrooks.co.uk

CUSTOMER SERVICE, SPARES & TECHNICAL ENQUIRIES

+44 (0)1902 390 894

technical@lefroybrooks.co.uk

LEFROYBROOKS.CO.UK

20.065.124C / MARCH 2021

Lefroy Brooks RL 1236 Installation & Servicing Guide

Brand: Lefroy Brooks

Model: RL 1236

Type: Installation & Servicing Guide

This manual is also suitable for

Sorry, I do not have information about Lefroy Brooks RL 1236 in the context. Therefore, I am unable to generate a response to your request.

Download PDF

report

Lefroy Brooks RL 1236 Installation & Servicing Guide

This manual is also suitable for

Lefroy Brooks RL 1236 Installation & Servicing Guide

Related papers

Other documents