WELL STAR™
Installation Instructions
RELEASE DATE
9-8-15
REFERENCE NUMBER
INS000968
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
Dia.
(56mm)
(32mm)
1 1/4"
(191mm)
7 1/2"
2 1/4"
8 3/4"
(222mm)
(42mm)
1 5/8" Dia.
(56mm)
8 3/4"
(222mm)
(32mm)
1 1/4"
Dia.2 1/4"
7 1/2"
(191mm)
(42mm)
1 5/8" Dia.
6" Dia.
(152mm)
2 1/4" Dia.
(57mm)
1 1/2" O.C.
(38mm)
7/8"
(152mm)
(22mm)
Concrete
Pour Collar
5’
(1524mm)
18 Ga.
2 low voltage
direct burial
cable
TOOLS
NEEDED:
By Others
3/32” & 3/16” Allen Wrench
Waterproof Wire Connectors
Dia.
(56mm)
(32mm)
1 1/4"
(191mm)
7 1/2"
2 1/4"
8 3/4"
(222mm)
(42mm)
1 5/8" Dia.
(56mm)
8 3/4"
(222mm)
(32mm)
1 1/4"
Dia.2 1/4"
7 1/2"
(191mm)
(42mm)
1 5/8" Dia.
6" Dia.
(152mm)
2 1/4" Dia.
(57mm)
1 1/2" O.C.
(38mm)
7/8"
(152mm)
(22mm)
Concrete
Pour Collar
5’
(1524mm)
18 Ga.
2 low voltage
direct burial
cable
Dia.
(56mm)
(32mm)
1 1/4"
(191mm)
7 1/2"
2 1/4"
8 3/4"
(222mm)
(42mm)
1 5/8" Dia.
(56mm)
8 3/4"
(222mm)
(32mm)
1 1/4"
Dia.2 1/4"
7 1/2"
(191mm)
(42mm)
1 5/8" Dia.
6" Dia.
(152mm)
2 1/4" Dia.
(57mm)
1 1/2" O.C.
(38mm)
7/8"
(152mm)
(22mm)
Concrete
Pour Collar
5’
(1524mm)
18 Ga.
2 low voltage
direct burial
cable
Dia.
(56mm)
(32mm)
1 1/4"
(191mm)
7 1/2"
2 1/4"
8 3/4"
(222mm)
(42mm)
1 5/8" Dia.
(56mm)
8 3/4"
(222mm)
(32mm)
1 1/4"
Dia.2 1/4"
7 1/2"
(191mm)
(42mm)
1 5/8" Dia.
6" Dia.
(152mm)
2 1/4" Dia.
(57mm)
1 1/2" O.C.
(38mm)
7/8"
(152mm)
(22mm)
Concrete
Pour Collar
5’
(1524mm)
18 Ga.
2 low voltage
direct burial
cable
Dia.
(56mm)
(32mm)
1 1/4"
(191mm)
7 1/2"
2 1/4"
8 3/4"
(222mm)
(42mm)
1 5/8" Dia.
(56mm)
8 3/4"
(222mm)
(32mm)
1 1/4"
Dia.2 1/4"
7 1/2"
(191mm)
(42mm)
1 5/8" Dia.
6" Dia.
(152mm)
2 1/4" Dia.
(57mm)
1 1/2" O.C.
(38mm)
7/8"
(152mm)
(22mm)
Concrete
Pour Collar
5’
(1524mm)
18 Ga.
2 low voltage
direct burial
cable
12"
(305mm)
(2) Stainless Steel at Head
Hex Head Screws Block Oxide
6" Dia.
(152mm)
.120" Wall,
Steel Housing
(152mm)
6" Dia
12"
(305mm)
(152mm)
6" Dia
For Remote Transformer
See Sheets TRSS Series, TR Series,
Power Pipe, Power II or Power
Canopy in Accessory Section.
Tempered Glass Lens
Cast Iron Well Cover
(Cast 35, Gray Iron-ASTM A43)
4 3/8" O.C.
(111mm)
5’
(1524mm)
12 Ga.
2 low voltage
direct burial
cable
This set of instructions
works for:
WS - Well Star™
WS Cast Iron Faceplate
Steel Housing
5’ of 18 Gauge Wire
TECHNOLOGY
with
TECHNOLOGY
Hot Surface
Warning Low Voltage
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping of
this product.
• Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, O-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact only switch/plug when
turning on.
Do not touch hot lens, guard, or enclosure (see diagram/
picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth. Oil
from skin may damage lamp.
Do not operate the luminaire fitting with a missing or
damaged shield.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations · Suitable for recessed in ground locations
IMPORTANT LISTINGS AND CERTIFICATIONS
& Low Voltage
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
A. Determine Soil Type by referencing
DIG-IT Guide. Prep soil according to
DIG-IT Guide.
Soil Prep
B. Excavate a hole to the necessary
dimensions for fixture placement
according to lighting plan.
Conduit
trench
Proper soil preparation is recommended before installation. See the DIG-IT guide at www.bklighting.com/dig-it for more information.
RELEASE DATE
9-8-15
REFERENCE NUMBER
INS000968
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
PROJECT:
TYPE:
Finished grade
Finished grade
12”
2 window
faceplate
shown
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
COM
2 window
faceplate
shown
Optical opening on
faceplate will align with
alignment arrows on
temporary cover
Optical opening on
faceplate will align with
alignment arrows on
temporary cover
Pea gravel or sand
Finished grade
Dirt or soil
Stability flange
Rebar or stake (by others)
Pea gravel or sand
Finished grade
Concrete
Finished grade
Finished grade
Pea gravel or sand
Finished grade
Dirt or soil
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
Finished grade
Finished grade
12”
2 window
faceplate
shown
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
COM
2 window
faceplate
shown
Optical opening on
faceplate will align with
alignment arrows on
temporary cover
Optical opening on
faceplate will align with
alignment arrows on
temporary cover
Pea gravel or sand
Finished grade
Dirt or soil
Stability flange
Rebar or stake (by others)
Pea gravel or sand
Finished grade
Concrete
Finished grade
Finished grade
Pea gravel or sand
Finished grade
Dirt or soil
12"
(305mm)
(2) Stainless Steel at Head
Hex Head Screws Block Oxide
6" Dia.
(152mm)
.120" Wall,
Steel Housing
(152mm)
6" Dia
12"
(305mm)
(152mm)
6" Dia
For Remote Transformer
See Sheets TRSS Series, TR Series,
Power Pipe, Power II or Power
Canopy in Accessory Section.
Tempered Glass Lens
Cast Iron Well Cover
(Cast 35, Gray Iron-ASTM A43)
4 3/8" O.C.
(111mm)
5’
(1524mm)
12 Ga.
2 low voltage
direct burial
cable
WELL STAR™
Installation Instructions
TECHNOLOGY
with
TECHNOLOGY
4. Insert fixture housing and low voltage wire into
trench.
5. Back fill with pea gravel or sand to allow
sufficient drainage. Install housing flush at
grade. Install faceplate with (2) 1/4-20 screws
using a 3/16” Allen wrench.
2. Supply low voltage wiring necessary for
installation (By Others). See wiring diagram.
NOTE: Leave sufficient wire length in the
fixture housing for future service.
Finished grade
Finished grade
12”
2 window
faceplate
shown
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
COM
2 window
faceplate
shown
Optical opening on
faceplate will align with
alignment arrows on
temporary cover
Optical opening on
faceplate will align with
alignment arrows on
temporary cover
Pea gravel or sand
Finished grade
Dirt or soil
Stability flange
Rebar or stake (by others)
Pea gravel or sand
Finished grade
Concrete
Finished grade
Finished grade
Pea gravel or sand
Finished grade
Dirt or soil
Finished grade
8 3/4”
2 window
faceplate
shown
Finished grade
8 3/4”
LINE 12V
FIXTURE
COM
Remote
Transformer
COM
Optical opening on
faceplate will align with
alignment arrows on
temporary cover
Optical opening on
faceplate will align with
alignment arrows on
temporary cover
Stability flange
Rebar or stake (by others)
Pea gravel or sand
Finished grade
Concrete
Stability flange
Rebar or stake (by others)
Pea gravel or sand
Finished grade
Concrete
Finished grade Concrete
Wire nuts must
clear opening
6”
min.
1. Excavate trench according to designed lighting
plan, 20” deep and 10” wide suitable for the 13”
fixture housing. 3. Make watertight connections using proper
waterproof connectors (By Others) from remote
transformer to fixture leads.
Finished grade
Finished grade
12”
2 window
faceplate
shown
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
COM
2 window
faceplate
shown
Optical opening on
faceplate will align with
alignment arrows on
temporary cover
Optical opening on
faceplate will align with
alignment arrows on
temporary cover
Pea gravel or sand
Finished grade
Dirt or soil
Stability flange
Rebar or stake (by others)
Pea gravel or sand
Finished grade
Concrete
Finished grade
Finished grade
Pea gravel or sand
Finished grade
Dirt or soil
& Low Voltage
WIRING DIAGRAM
-
1
-
2
B-K lighting LED Lamp - MR16 Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
B-K lighting Square Adjustable Well Star - MR16 Installation guide
-
B-K lighting Mini-Micro Flush Mount Installation guide
-
B-K lighting Hume Flush/Surface Mount Installation guide
-
B-K lighting Mini-Micro Surface Mount Installation guide
-
B-K lighting ArtiStar Surface Mount Installation guide
-
B-K lighting Denali Integral Flush Mount Installation guide
-
B-K lighting ArtiStar Flush Mount Installation guide
-
B-K lighting Denali Integral Surface Mount Installation guide
-
B-K lighting Denali Flush Mount Installation guide
-
B-K lighting Denali Surface Mount Installation guide
