B-K lighting Square Adjustable Well Star - MR16 Installation guide
- Type
- Installation guide
SQUARE ADJUSTABLE WELL STAR™
Installation Instructions
RELEASE DATE
9-8-15
REFERENCE NUMBER
INS000969
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
15/16"
(321mm)
12 5/8"
(24mm)
6” Dia.
6” Dia.
(152mm)
PVC
Housing
6 7/8"
Square
(176mm)
Stainless Steel
Vertical
Aiming Bracket
with Positive
Locking Screw
(321mm)
12 5/8"
20°
15/16"
(24mm)
(152mm)
PVC
Housing
Cast Brass
(Finished as Specied )
5’
(1524mm)
12 Ga.
2 low voltage
direct burial
cable
TOOLS
NEEDED:
By Others
3/16” Allen Wrench
Waterproof Wire Connectors
Phillips Screwdriver
This set of instructions
works for:
SW - Square Adjustable
Well Star™
SW
Composite Housing
Brass Faceplate and
Concrete Pour Collar
5’ of 18 gauge wire
TECHNOLOGY
with
TECHNOLOGY
Hot Surface
Warning Low Voltage
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping of
this product.
• Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, O-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact only switch/plug when
turning on.
Do not touch hot lens, guard, or enclosure (see diagram/
picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth. Oil
from skin may damage lamp.
Do not operate the luminaire fitting with a missing or
damaged shield.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations · Suitable for recessed in ground locations
IMPORTANT LISTINGS AND CERTIFICATIONS
& Low Voltage
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
A. Determine Soil Type by referencing
DIG-IT Guide. Prep soil according to
DIG-IT Guide.
Soil Prep
B. Excavate a hole to the necessary
dimensions for fixture placement
according to lighting plan.
Conduit
trench
Proper soil preparation is recommended before installation. See the DIG-IT guide at www.bklighting.com/dig-it for more information.
PROJECT:
TYPE:
RELEASE DATE
9-8-15
REFERENCE NUMBER
INS000969
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
Dia.
(56mm)
(32mm)
1 1/4"
(191mm)
7 1/2"
2 1/4"
8 3/4"
(222mm)
(42mm)
1 5/8" Dia.
(56mm)
8 3/4"
(222mm)
(32mm)
1 1/4"
Dia.2 1/4"
7 1/2"
(191mm)
(42mm)
1 5/8" Dia.
6" Dia.
(152mm)
2 1/4" Dia.
(57mm)
1 1/2" O.C.
(38mm)
7/8"
(152mm)
(22mm)
Concrete
Pour Collar
5’
(1524mm)
18 Ga.
2 low voltage
direct burial
cable
Dia.
(56mm)
(32mm)
1 1/4"
(191mm)
7 1/2"
2 1/4"
8 3/4"
(222mm)
(42mm)
1 5/8" Dia.
(56mm)
8 3/4"
(222mm)
(32mm)
1 1/4"
Dia.2 1/4"
7 1/2"
(191mm)
(42mm)
1 5/8" Dia.
6" Dia.
(152mm)
2 1/4" Dia.
(57mm)
1 1/2" O.C.
(38mm)
7/8"
(152mm)
(22mm)
Concrete
Pour Collar
5’
(1524mm)
18 Ga.
2 low voltage
direct burial
cable
Dia.
(56mm)
(32mm)
1 1/4"
(191mm)
7 1/2"
2 1/4"
8 3/4"
(222mm)
(42mm)
1 5/8" Dia.
(56mm)
8 3/4"
(222mm)
(32mm)
1 1/4"
Dia.2 1/4"
7 1/2"
(191mm)
(42mm)
1 5/8" Dia.
6" Dia.
(152mm)
2 1/4" Dia.
(57mm)
1 1/2" O.C.
(38mm)
7/8"
(152mm)
(22mm)
Concrete
Pour Collar
5’
(1524mm)
18 Ga.
2 low voltage
direct burial
cable
Dia.
(56mm)
(32mm)
1 1/4"
(191mm)
7 1/2"
2 1/4"
8 3/4"
(222mm)
(42mm)
1 5/8" Dia.
(56mm)
8 3/4"
(222mm)
(32mm)
1 1/4"
Dia.2 1/4"
7 1/2"
(191mm)
(42mm)
1 5/8" Dia.
6" Dia.
(152mm)
2 1/4" Dia.
(57mm)
1 1/2" O.C.
(38mm)
7/8"
(152mm)
(22mm)
Concrete
Pour Collar
5’
(1524mm)
18 Ga.
2 low voltage
direct burial
cable
Dia.
(56mm)
(32mm)
1 1/4"
(191mm)
7 1/2"
2 1/4"
8 3/4"
(222mm)
(42mm)
1 5/8" Dia.
(56mm)
8 3/4"
(222mm)
(32mm)
1 1/4"
Dia.2 1/4"
7 1/2"
(191mm)
(42mm)
1 5/8" Dia.
6" Dia.
(152mm)
2 1/4" Dia.
(57mm)
1 1/2" O.C.
(38mm)
7/8"
(152mm)
(22mm)
Concrete
Pour Collar
5’
(1524mm)
18 Ga.
2 low voltage
direct burial
cable
15/16"
(321mm)
12 5/8"
(24mm)
6” Dia.
6” Dia.
(152mm)
PVC
Housing
6 7/8"
Square
(176mm)
Stainless Steel
Vertical
Aiming Bracket
with Positive
Locking Screw
(321mm)
12 5/8"
20°
15/16"
(24mm)
(152mm)
PVC
Housing
Cast Brass
(Finished as Specied )
5’
(1524mm)
12 Ga.
2 low voltage
direct burial
cable
SQUARE ADJUSTABLE WELL STAR™
Installation Instructions
5. Align and orientate Concrete Pour Collar on
housing to illuminated object. Back fill with pea
gravel or sand to allow sufficient drainage. Install
housing flush at grade. See wiring diagram.
6. Make watertight connections from remote
transformer to fixture leads using waterproof
wire connectors (By Others).
7. Loosen stainless steel Phillips head cap screw
on adjustable bracket, aim to desired location.
Tighten to maintain aiming position.
Finished grade
Finished grade
12”
2 window
faceplate
shown
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
COM
2 window
faceplate
shown
Optical opening on
faceplate will align with
alignment arrows on
temporary cover
Optical opening on
faceplate will align with
alignment arrows on
temporary cover
Pea gravel or sand
Finished grade
Dirt or soil
Stability flange
Rebar or stake (by others)
Pea gravel or sand
Finished grade
Concrete
Finished grade
Finished grade
Pea gravel or sand
Finished grade
Dirt or soil
Finished grade
8 3/4”
2 window
faceplate
shown
Finished grade
8 3/4”
LINE 12V
FIXTURE
COM
Remote
Transformer
COM
Optical opening on
faceplate will align with
alignment arrows on
temporary cover
Optical opening on
faceplate will align with
alignment arrows on
temporary cover
Stability flange
Rebar or stake (by others)
Pea gravel or sand
Finished grade
Concrete
Stability flange
Rebar or stake (by others)
Pea gravel or sand
Finished grade
Concrete
Finished grade Concrete
Wire nuts must
clear opening
6”
min.
8. Attach faceplate to Concrete Pour Collar with (4)
1/4-20 screws using a 3/16” Allen wrench.
Finished grade
Finished grade
12”
2 window
faceplate
shown
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
COM
2 window
faceplate
shown
Optical opening on
faceplate will align with
alignment arrows on
temporary cover
Optical opening on
faceplate will align with
alignment arrows on
temporary cover
Pea gravel or sand
Finished grade
Dirt or soil
Stability flange
Rebar or stake (by others)
Pea gravel or sand
Finished grade
Concrete
Finished grade
Finished grade
Pea gravel or sand
Finished grade
Dirt or soil
TECHNOLOGY
with
TECHNOLOGY
& Low Voltage
2. Supply low voltage wiring necessary for
installation (By Others)
NOTE: Leave sufficient wire length in the
fixture housing for future service.
Finished grade
Finished grade
12”
2 window
faceplate
shown
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
COM
2 window
faceplate
shown
Optical opening on
faceplate will align with
alignment arrows on
temporary cover
Optical opening on
faceplate will align with
alignment arrows on
temporary cover
Pea gravel or sand
Finished grade
Dirt or soil
Stability flange
Rebar or stake (by others)
Pea gravel or sand
Finished grade
Concrete
Finished grade
Finished grade
Pea gravel or sand
Finished grade
Dirt or soil
Finished grade
Finished grade
12”
2 window
faceplate
shown
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
COM
2 window
faceplate
shown
Optical opening on
faceplate will align with
alignment arrows on
temporary cover
Optical opening on
faceplate will align with
alignment arrows on
temporary cover
Pea gravel or sand
Finished grade
Dirt or soil
Stability flange
Rebar or stake (by others)
Pea gravel or sand
Finished grade
Concrete
Finished grade
Finished grade
Pea gravel or sand
Finished grade
Dirt or soil
1. Excavate trench according to designed lighting
plan 20” deep and 10” wide suitable for the 13”
fixture housing.
3. Remove faceplate from housing by loosening (4)
1/4-20 screws using 3/16” Allen wrench.
4. Place housing in excavated trench and pull wire
through housing.
Finished grade
Finished grade
12”
2 window
faceplate
shown
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
COM
2 window
faceplate
shown
Optical opening on
faceplate will align with
alignment arrows on
temporary cover
Optical opening on
faceplate will align with
alignment arrows on
temporary cover
Pea gravel or sand
Finished grade
Dirt or soil
Stability flange
Rebar or stake (by others)
Pea gravel or sand
Finished grade
Concrete
Finished grade
Finished grade
Pea gravel or sand
Finished grade
Dirt or soil
PROJECT:
TYPE:
Dia.
(56mm)
(32mm)
1 1/4"
(191mm)
7 1/2"
2 1/4"
8 3/4"
(222mm)
(42mm)
1 5/8" Dia.
(56mm)
8 3/4"
(222mm)
(32mm)
1 1/4"
Dia.2 1/4"
7 1/2"
(191mm)
(42mm)
1 5/8" Dia.
6" Dia.
(152mm)
2 1/4" Dia.
(57mm)
1 1/2" O.C.
(38mm)
7/8"
(152mm)
(22mm)
Concrete
Pour Collar
5’
(1524mm)
18 Ga.
2 low voltage
direct burial
cable
Dia.
(56mm)
(32mm)
1 1/4"
(191mm)
7 1/2"
2 1/4"
8 3/4"
(222mm)
(42mm)
1 5/8" Dia.
(56mm)
8 3/4"
(222mm)
(32mm)
1 1/4"
Dia.2 1/4"
7 1/2"
(191mm)
(42mm)
1 5/8" Dia.
6" Dia.
(152mm)
2 1/4" Dia.
(57mm)
1 1/2" O.C.
(38mm)
7/8"
(152mm)
(22mm)
Concrete
Pour Collar
5’
(1524mm)
18 Ga.
2 low voltage
direct burial
cable
Dia.
(56mm)
(32mm)
1 1/4"
(191mm)
7 1/2"
2 1/4"
8 3/4"
(222mm)
(42mm)
1 5/8" Dia.
(56mm)
8 3/4"
(222mm)
(32mm)
1 1/4"
Dia.2 1/4"
7 1/2"
(191mm)
(42mm)
1 5/8" Dia.
6" Dia.
(152mm)
2 1/4" Dia.
(57mm)
1 1/2" O.C.
(38mm)
7/8"
(152mm)
(22mm)
Concrete
Pour Collar
5’
(1524mm)
18 Ga.
2 low voltage
direct burial
cable
Dia.
(56mm)
(32mm)
1 1/4"
(191mm)
7 1/2"
2 1/4"
8 3/4"
(222mm)
(42mm)
1 5/8" Dia.
(56mm)
8 3/4"
(222mm)
(32mm)
1 1/4"
Dia.2 1/4"
7 1/2"
(191mm)
(42mm)
1 5/8" Dia.
6" Dia.
(152mm)
2 1/4" Dia.
(57mm)
1 1/2" O.C.
(38mm)
7/8"
(152mm)
(22mm)
Concrete
Pour Collar
5’
(1524mm)
18 Ga.
2 low voltage
direct burial
cable
Dia.
(56mm)
(32mm)
1 1/4"
(191mm)
7 1/2"
2 1/4"
8 3/4"
(222mm)
(42mm)
1 5/8" Dia.
(56mm)
8 3/4"
(222mm)
(32mm)
1 1/4"
Dia.2 1/4"
7 1/2"
(191mm)
(42mm)
1 5/8" Dia.
6" Dia.
(152mm)
2 1/4" Dia.
(57mm)
1 1/2" O.C.
(38mm)
7/8"
(152mm)
(22mm)
Concrete
Pour Collar
5’
(1524mm)
18 Ga.
2 low voltage
direct burial
cable
15/16"
(321mm)
12 5/8"
(24mm)
6” Dia.
6” Dia.
(152mm)
PVC
Housing
6 7/8"
Square
(176mm)
Stainless Steel
Vertical
Aiming Bracket
with Positive
Locking Screw
(321mm)
12 5/8"
20°
15/16"
(24mm)
(152mm)
PVC
Housing
Cast Brass
(Finished as Specied )
5’
(1524mm)
12 Ga.
2 low voltage
direct burial
cable
SQUARE ADJUSTABLE WELL STAR™
Installation Instructions
TECHNOLOGY
with TECHNOLOGY
& Low Voltage
1. Remove mounting screws. 2. Rotate large bracket 45º.
3. Secure mounting screw.
To Change Lamp Tilt Orientation
RELEASE DATE
9-8-15
REFERENCE NUMBER
INS000969
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
-
1
-
2
-
3
B-K lighting Square Adjustable Well Star - MR16 Installation guide
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
B-K lighting LED Lamp - MR16 Installation guide
-
B-K lighting Mini-Micro Flush Mount Installation guide
-
B-K lighting Mini-Micro Recessed Downlight Installation guide
-
B-K lighting Hume Flush/Surface Mount Installation guide
-
B-K lighting Mini-Micro Surface Mount Installation guide
-
B-K lighting ArtiStar Surface Mount Installation guide
-
B-K lighting Denali Integral Flush Mount Installation guide
-
B-K lighting ArtiStar Flush Mount Installation guide
-
B-K lighting Denali Flush Mount Installation guide
-
B-K lighting Denali Integral Surface Mount Installation guide
