Radiant P1220 Configuration manual

Brand: Radiant

Model: P1220

Category: POS terminals

Type: Configuration manual

This manual is also suitable for

Configuring Radiant POS terminals 1

Configuring Radiant POS terminals

Each Radiant Point-of-Sale terminal includes an Intel Pentium M or Celeron M processor,

a 15” or 12” touchscreen monitor, and an integrated magnetic stripe reader (MSR).

Radiant POS terminals can be configured with an electronic cash drawer, a thermal

receipt printer, a 2-line x 20-character external pole display or built-in line display, and a

barcode scanner.

After you unpack and connect your Radiant hardware, follow the appropriate instructions

in the current CounterPoint Installation Guide

to install CounterPoint and configure each

Radiant POS terminal as a CounterPoint workstation.

NOTE: If you are running CounterPoint over Windows Terminal Services, you will

configure your terminal server as a CounterPoint workstation, instead of your

POS terminals.

When you finish installing CounterPoint, complete the appropriate steps—depending on

which POS terminal(s) you are using and whether you are running CounterPoint over

Terminals Services—to configure your Radiant hardware for use with CounterPoint, as

outlined in the following tasks:

y Configuring Radiant hardware for Terminal Services

y Configuring the P1550 POS terminal

y Configuring the P1515/P1520 POS terminal

y Configuring the P1220 POS terminal

Configuring Radiant POS terminals 2

Configuring Radiant hardware for Terminal Services

Skip this section if you are not running CounterPoint over Terminal Services.

If you are running CounterPoint over Windows Terminal Services, you must perform

some preliminary steps to configure your Radiant POS terminals and peripherals to work

with Terminal Services.

When you finish installing CounterPoint, you must perform each of the tasks listed

below—as detailed on the following pages—to configure your Radiant POS terminals for

use with Terminal Services:

y Configure Remote Desktop Connection settings

y Configure MSR settings

y Configure 2x20 display settings

Configure Remote Desktop Connection settings

Follow these steps to configure the Remote Desktop Connection settings on each of your

Radiant POS terminals:

1. From one of your POS terminals, select Start > Programs > Accessories >

Communications > Remote Desktop Connection.

2. Click the Options button, and then click the Local

Resources tab.

3. Select the On the local computer option from the

Apply Windows key combinations list.

4. Under Local devices, select the Printers check box if

you are using a Windows printer with the POS

terminal.

5. Select the Serial ports check box.

6. Configure the settings on the remaining tabs to

allow your POS terminal to connect to your terminal

server and start a Terminal Services session.

7. Click Connect to connect to your terminal server.

NOTE: Repeat these steps for each of your Radiant POS terminals.

Configuring Radiant POS terminals 3

Configure MSR settings

Follow these steps to allow your POS terminals’ built-in MSRs to function over Windows

Terminal Services:

1. Copy the OPOSim.exe file from your top-level directory of your CounterPoint server to

the Windows Startup directory for all users (i.e., C:\Documents and Settings\All Users\Start

Menu\Programs\Startup) on your terminal server.

2. On your terminal server, double-click OPOSim.exe in the Startup directory to start the

OPOS Input Manager.

3. From a command prompt window, browse to the C:\Program Files\OPOS\CommonCO

directory on your terminal server, and then enter the following command to register

the necessary .dll files:

regansi

Configure 2x20 display settings

Follow these steps to allow the 2x20 displays connected to your POS terminals to

function over Terminal Services:

1. On your CounterPoint server, browse to your top-level directory (e.g., C:\SYN) and

double-click the SYNRUN.SYN file to open it in Notepad or another text editor.

2. If you are using any P1220 or P1550 terminals with external (i.e., pole mount) 2x20

displays, add the following lines to SYNRUN.SYN:

CPSIO2=WN

SYNCOM2=F8n1

3. If you are using any P1220 terminals with built-in (POS mount) 2x20 displays, add

the following lines to SYNRUN.SYN:

CPSIO5=WN

SYNCOM5=T8n1

4. If you are using P1520 terminals with external (pole mount) or built-in (POS mount)

2x20 display, add the following lines to SYNRUN.SYN:

CPSIO4=WN

SYNCOM4=F8n1

5. Save the modified SYNRUN.SYN file, and then close your text editor.

Configuring Radiant POS terminals 4

Configuring the P1550 POS terminal

Follow these steps to configure a P1550 POS terminal for use with CounterPoint:

1. If you are using any of the following external devices with your P1550 POS terminal,

connect them to the following ports:

Device Radiant Part # Port

Printer-driven cash drawer

(16” or 18.8”)

P000F024 or

P000F031

DK (on Epson TM-T88)

Epson TM-T88 series receipt printer

(RS232 interface)

P201F019 or

P201F039

Serial 1

2x20 display (POS mount or

pole mount)

P703F000 or

P703F001

Serial 2

Serial modem N/A

USB (with USB to serial adapter)

NOTE: If you are using a serial modem with your P1550, follow the instructions included

with your USB to serial adapter to connect the modem to an available USB port.

2. Browse to the top-level directory on your CounterPoint server (e.g., C:\SYN) and

double-click the SYNRUN.SYN file to open it in Notepad or another text editor.

3. Add the following lines to SYNRUN.SYN:

CPSIO1=C

SYNCOM1=98n1

4. If you are not running CounterPoint over Terminal Services, add the following line to

SYNRUN.SYN:

CPSIO2=W

5. Save the modified SYNRUN.SYN file, and then close your text editor.

6. Copy the CP1550Mode.bat and OPOSim.exe files from your top-level directory to the

Windows Startup directory for all users (i.e., C:\Documents and Settings\All Users\Start

Menu\Programs\Startup) on your POS terminal.

7. Double-click OPOSim.exe in the Startup directory to start the OPOS Input Manager.

8. Right-click the OPOS Input Manager icon (

) in the Windows

system tray and select Options to display the OPOS Input

Manager window.

9. Select RSMsr from the MSR list, and then select the Track

you want to read.

NOTE: If you are processing debit cards, select track 2.

10. Select the Auto-enable on start-up check box, and then click

the Enable button.

11. Close the OPOS Input Manager window.

12. Select Start / Settings / Printers and Faxes, right-click the Epson TM-T88 - Serial printer, and

then click Properties.

Configuring Radiant POS terminals 5

13. Click the Ports tab, select an unused Serial Port (e.g., COM4), and then click OK.

NOTE: Alternatively, you can delete the Epson TM-T88 - Serial printer, instead of assigning

it to an unused port.

14. Start CounterPoint and log in to your company database.

15. Select File Utilities / Special / System / Update pre-defined data.

16. Select Yes from the Are you sure you want to do this ? prompt, and then press Enter to

load the pre-defined device codes for Radiant POS terminals.

17. When the pre-defined data is updated, press ESC to return to the main menu.

18. Select Setup / Point of Sale / Registers, specify a Register number for your POS terminal,

and then complete the remaining fields on the first Registers screen.

19. On the next Registers screen, enter 1550 in the Device code field for the Printer 1 device,

select the Print method you want to use, and then enter COM1 in the corresponding

Device ID field.

20. Enter or look up one or more Form ID options to specify the forms you want to print

with your receipt printer.

Configuring Radiant POS terminals 6

21. On the next Registers screen, enter 1550 in the Device code field for the Card reader

device.

NOTE: Do not specify a Device ID for the Card reader device.

22. Enter 1550 in the Device code field for the Display device, and then enter COM2 in the

corresponding Device ID field.

23. Press Enter at the Field number to change ? prompt to save your changes, and then

press ESC to close the Registers screen and return to the main menu.

24. Select Setup / Point of Sale / Drawers, specify a Drawer number and Register number for the

POS terminal’s cash drawer, and then enter a Description for the drawer.

25. Enter 1550 in the Drawer device code field, and then enter COM1 in the Drawer device ID

field.

26. Press Enter at the Field number to change ? prompt to save your changes, and then

press ESC to close the Drawers screen and return to the main menu.

Your P1550 POS terminal is ready to use! Start Ticket Entry or Touchscreen Ticket Entry and

enter some sample tickets to try out each device. If you encounter any problems with

your devices, test each device in Setup / Point of Sale / Device codes.

Configuring Radiant POS terminals 7

Configuring the P1515/P1520 POS terminal

Follow these steps to configure a P1515 or P1520 POS terminal for use with

CounterPoint:

1. If you are using any of the following external devices with your P1515 or P1520,

connect them to the following ports:

Device Radiant Part # Port

Printer-driven cash drawer

(16” or 18.8”)

P000F024 or

P000F031

DK (on Epson TM-T88)

Epson TM-T88 series receipt printer

(RS232 interface)

P201F019 or

P201F039

Serial 3

2x20 display (POS mount or

pole mount)

P703F000 or

P703F001

Serial 4

Serial modem N/A

USB (with USB to serial adapter)

NOTE: If you are using a serial modem with your P1515 or P1520, follow the instructions

included with your USB to serial adapter to connect the modem to an available

USB port.

2. Browse to your top-level directory (e.g., C:\SYN) and double-click the SYNRUN.SYN file

to open it in Notepad or another text editor.

3. Add the following lines to SYNRUN.SYN:

CPSIO3=C

SYNCOM3=98n1

4. If you are not running CounterPoint over Terminal Services, add the following line to

SYNRUN.SYN:

CPSIO4=W

5. Save the modified SYNRUN.SYN file, and then close your text editor.

6. Copy the CP1550Mode.bat and OPOSim.exe files from your top-level directory to the

Windows Startup directory for all users (i.e., C:\Documents and Settings\All Users\Start

Menu\Programs\Startup).

7. Select Start / Settings / Printers and Faxes, right-click the Epson TM-T88 - Serial printer, and

then click Properties.

8. Click the Ports tab, select an unused Serial Port (e.g., COM6), and then click OK.

NOTE: Alternatively, you can delete the Epson TM-T88 - Serial printer, instead of assigning

it to an unused port.

9. Start CounterPoint and log in to your company database.

10. Select File Utilities / Special / System / Update pre-defined data.

11. Select Yes from the Are you sure you want to do this ? prompt, and then press Enter to

load the pre-defined device codes for Radiant POS terminals.

12. When the pre-defined data is updated, press ESC to return to the main menu.

13. Select Setup / Point of Sale / Registers, specify a Register number for your POS terminal,

and then complete the remaining fields on the first Registers screen.

Configuring Radiant POS terminals 8

14. On the next Registers screen, enter 1520 in the Device code field for the Printer 1 device,

select the Print method you want to use, and then enter COM3 in the corresponding

Device ID field.

15. Enter or look up one or more Form ID options to specify the forms you want to print

with your receipt printer.

16. On the next Registers screen, enter 1520 in the Device code field for the Display device,

and then enter COM4 in the corresponding Device ID field.

17. Press Enter at the Field number to change ? prompt to save your changes, and then

press ESC to close the Registers screen and return to the main menu.

18. Select Setup / Point of Sale / Drawers, specify a Drawer number and Register number for the

POS terminal’s cash drawer, and then enter a Description for the drawer.

19. Enter 1520 in the Drawer device code field, and then enter COM3 in the Drawer device ID

field.

20. Press Enter at the Field number to change ? prompt to save your changes, and then

press ESC to close the Drawers screen and return to the main menu.

Configuring Radiant POS terminals 9

Configuring the P1515/P1520 Payment Guard MSR

If you are setting up a P1515 or a P1520 POS terminal with a Payment Guard MSR

(available as of July 1, 2010), follow these steps to configure the MSR:

1. Download the RadUSerialMSR1-0-0-1.zip file from the Support area of the CounterPoint

Web site (www.counterpointpos.com/support/softwa

re_cpv7.htm) and extract the

archive to a temporary directory.

2. Browse to the directory to which you extracted the RadUSerialMSR1-0-0-1.zip archive

and double-click Setup.exe to install the Payment Guard MSR driver.

3. In the directory to which you extracted the RadUSerialMSR1-0-0-1.zip archive, double-

click the MSRtracks_2only.reg file, and then click Yes on the Registry Editor dialog to

update the Windows registry with the track settings for the Payment Guard MSR.

4. Click OK to close the Registry Editor dialog.

5. In CounterPoint, select Setup > Point of Sale > Registers, specify the Register number for

your POS terminal, and then proceed to the third Registers screen.

6. Enter 1520 in the Device code field for the Card reader device and enter COM5 in the

corresponding Device ID field.

Configuring the P1520 keyboard-transparent MSR

If you are setting up a P1520 POS terminal with a keyboard-transparent MSR (available

before July 1, 2010), follow these steps to configure the MSR:

1. Double-click OPOSim.exe in the Startup directory to start the OPOS Input Manager.

2. Right-click the OPOS Input Manager icon (

) in the Windows

system tray and select Options to display the OPOS Input

Manager window.

3. Select RSMsr from the MSR list, and then select the Track

you want to read.

NOTE: If you are processing debit cards, select track 2.

4. Select the Auto-enable on start-up check box, and then click

the Enable button.

5. Close the OPOS Input Manager window.

6. In CounterPoint, select Setup > Point of Sale > Registers, specify the Register number for

your POS terminal, and then proceed to the third Registers screen.

7. Enter 1520 in the Device code field for the Card reader device.

NOTE: Do not specify a Device ID for the Card reader device.

Your POS terminal is ready to use! Start Ticket Entry or Touchscreen Ticket Entry and enter

some sample tickets to try out each device. If you encounter any problems with your

devices, test each device in Setup / Point of Sale / Device codes.

Configuring Radiant POS terminals 10

Configuring the P1220 POS terminal

Follow these steps to configure a P1220 POS terminal for use with CounterPoint:

1. If you are using any of the following external devices with your P1220, connect them

to the following ports:

Device Radiant Part # Port

Printer-driven cash drawer

(16” or 18.8”)

P000F024 or

P000F031

DK (on Epson TM-T88)

Epson TM-T88 series receipt printer

(RS232 interface)

P201F019 or

P201F039

Serial 1

2x20 display (pole mount) P703F001

Serial 2

Serial modem N/A

USB (with USB to serial adapter)

NOTE: If you are using a serial modem with your P1220, follow the instructions included

with your USB to serial adapter to connect the modem to an available USB port.

2. Browse to your top-level directory (e.g., C:\SYN) and double-click the SYNRUN.SYN file

to open it in Notepad or another text editor.

3. Add the following lines to SYNRUN.SYN:

CPSIO1=C

SYNCOM1=98n1

4. If you are not running CounterPoint over Terminal Services and you are using an

external (i.e., pole mount) 2x20 display, add the following line to SYNRUN.SYN:

CPSIO2=W

5. If you are not running CounterPoint over Terminal Services and you are using the

P1220’s built-in (i.e., POS mount) 2x20 display, add the following line to SYNRUN.SYN:

CPSIO5=W

6. Save the modified SYNRUN.SYN file, and then close your text editor.

7. Copy the CP1220Mode.bat and OPOSim.exe files from your top-level directory to the

Windows Startup directory for all users (i.e., C:\Documents and Settings\All Users\Start

Menu\Programs\Startup).

8. Double-click OPOSim.exe in the Startup directory to start the OPOS Input Manager.

9. Right-click the OPOS Input Manager icon (

) in the Windows

system tray and select Options to display the OPOS Input

Manager window.

10. Select RSMsr from the MSR list, and then select the Track

you want to read.

NOTE: If you are processing debit cards, select track 2.

11. Select the Auto-enable on start-up check box, and then click

the Enable button.

12. Close the OPOS Input Manager window.

13. Select Settings / Printers and Faxes from the Start menu, right-click the Epson TM-T88 -

Serial printer, and then click Properties.

Configuring Radiant POS terminals 11

14. Click the Ports tab, select an unused Serial Port (e.g., COM4), and then click OK.

NOTE: Alternatively, you can delete the Epson TM-T88 – Serial printer, instead of assigning

it to an unused port.

15. Start CounterPoint and log in to your company database.

16. Select File Utilities / Special / System / Update pre-defined data.

17. Select Yes from the Are you sure you want to do this ? prompt, and then press Enter to

load the pre-defined device codes for Radiant POS terminals.

18. When the pre-defined data is updated, press ESC to return to the main menu.

19. Select Setup / Point of Sale / Registers, specify a Register number for your POS terminal,

and then complete the remaining fields on the first Registers screen.

20. On the next Registers screen, enter 1220 in the Device code field for the Printer 1 device,

select the Print method you want to use, and then enter COM1 in the corresponding

Device ID field.

21. Enter or look up one or more Form ID options to specify the forms you want to print

with your receipt printer.

22. On the next Registers screen, enter 1220 in the Device code field for the Card reader

device.

Configuring Radiant POS terminals 12

NOTE: Do not specify a Device ID for the Card reader device.

23. If you are using an external pole display, enter 1220 in the Device code field for the

Display device, and then enter COM2 in the corresponding Device ID field.

If your P1220 includes a built-in line display, enter 1220 in the Device code field for the

Display device, and then enter COM5 in the corresponding Device ID field.

24. Press Enter at the Field number to change ? prompt to save your changes, and then

press ESC to close the Registers screen and return to the main menu.

25. Select Setup / Point of Sale / Drawers, specify a Drawer number and Register number for the

POS terminal’s cash drawer, and then enter a Description for the drawer.

26. Enter 1220 in the Drawer device code field, and then enter COM1 in the Drawer device ID

field.

27. Press Enter at the Field number to change ? prompt to save your changes, and then

press ESC to close the Drawers screen and return to the main menu.

Your P1220 POS terminal is ready to use! Start Ticket Entry or Touchscreen Ticket Entry and

enter some sample tickets to try out each device. If you encounter any problems with

your devices, test each device in Setup / Point of Sale / Device codes.

Radiant P1220 Configuration manual

Brand: Radiant

Model: P1220

Category: POS terminals

Type: Configuration manual

This manual is also suitable for

Download PDF

report

Radiant P1220 Configuration manual

This manual is also suitable for

Radiant P1220 Configuration manual

Related papers

Other documents