Power Acoustik P3-15W Owner's manual

Power Acoustik
Brand
Power Acoustik
Model
P3-15W
Category
Speaker sets
Type
Owner's manual

This manual is also suitable for

Power Acoustik P3-15W is a high-performance subwoofer designed to deliver exceptional bass response and sound quality. With its 15-inch polypropylene injection-molded cone, butyl-rubber surround, and KSV Kapton voice coil, the P3-15W can handle up to 1200 watts RMS and produce a maximum power of 2800 watts. It features a dual 2-ohm voice coil configuration, allowing for various wiring options to achieve different impedance loads. The P3-15W is suitable for ported or sealed enclosures, with recommended volumes ranging from 2.00 to 4.00 cubic feet for ported and 1.25 to 2.

Power Acoustik P3-15W is a high-performance subwoofer designed to deliver exceptional bass response and sound quality. With its 15-inch polypropylene injection-molded cone, butyl-rubber surround, and KSV Kapton voice coil, the P3-15W can handle up to 1200 watts RMS and produce a maximum power of 2800 watts. It features a dual 2-ohm voice coil configuration, allowing for various wiring options to achieve different impedance loads. The P3-15W is suitable for ported or sealed enclosures, with recommended volumes ranging from 2.00 to 4.00 cubic feet for ported and 1.25 to 2.

P3 Features
Being the biggest brother in the new family of drivers requires even better parts and the ability to
meet expectations. Adding Conex spiders and larger Polyester-Imide enameled copper voice coils
wrapped on Kapton formers are the requirements for higher power handling, better heat dissipation,
and sonic quality. If you are the type of person who likes their face smacked against the dash due to
insane amounts of bass, step up to the big boys!
WWW.POWERACOUSTIK.COM
Driver Specifications
All enclosures should be made of .75” (3/4”) material only. When
possible, make the baffle 1.5” (1 1/2”) thick and add .75” (3/4”)
to the depth of the enclosure to compensate. All volumes
INCLUDE
vent/port and subwoofer displacements. DO NOT
change the volume unless you plan on adding a substantial amount
of bracing. For added performance, applying a coat of fiberglass
resin to the interior walls will greatly improve sealing the
enclosure. Adding a thin layer of poly-fill will improve response by
smoothing out reflections within the enclosure.
Enclosure Recommendations
Turn over for woofer wiring diagrams...
T/S Spec P3-10W P3-12W P3-15W
Fs (Hz)
29.62 28.42 24.58
Qms
7.115 7.238 7.655
Vas (ft
3
)
1.100 1.718 5.668
Xmax (mm)
11.50 13.25 13.25
Xmech (mm)
17.25 19.875 19.875
Qes
0.648 .741 0.780
Re (Ω)
4 4 4
Voice Coil (Ω) DVC 2Ω DVC 2Ω DVC 2Ω
V.C. Diameter (in.) 2.00” 2.50” 2.50”
BL (Tm) 12.43 14.27 14.23
RMS Power 800 1000 1200
Max Power 2000 2600 2800
Qts
0.594 .672 0.707
1w/1m SPL (dB) 82.85 83.65 86.73
Overall Diameter 10.50” 12.625” 15.75”
Overall Height 7.00” 7.50” 8.50”
Mounting Depth 6.75” 6.75” 7.75”
Cutout Diameter 9.25” 11.00” 14.00”
Flange Width 0.75” 0.875” 0.875”
Flange Height 0.625” 0.75” 0.75”
Weight (lbs.) 9.2 12.6 15.6
P3-10W Sealed P3-12W Sealed P3-15W Sealed
Cubic
Feet
Tuning
(Hz)
Cubic
Feet
Tuning
(Hz)
Cubic
Feet
Tuning
(Hz)
0.75 40.2 1.25 35.6 2.00 36.2
P3-10W Ported P3-12W Ported P3-15W Ported
Cubic
Feet
Port
Diameter
FB/F3
(Hz)
Cubic
Feet
Port
Diameter
FB/F3
(Hz)
Cubic
Feet
Port
Diameter
FB/F3
(Hz)
1.50 3" x 9" 35/29 2.00 4" x 12.5" 35/29 4.00 (2) 4" x 11.75" 35/30
Polypropylene Injection Molded Cone
Butyl-Rubber Surround
KSV Kapton Voice Coil
Nickel Plated 8 ga. Compression Wire Terminal
Suspension Integrated Tinsel Leads
Poly Cotton Spider
Texture Coat Finish on Stamped Steel Basket
2 Ω to Amplifier
1 Ω to Amplifier
1.33 Ω to Amplifier
1 Ω to Amplifier
  • Page 1 1
  • Page 2 2

Power Acoustik P3-15W Owner's manual

Power Acoustik
Brand
Power Acoustik
Model
P3-15W
Category
Speaker sets
Type
Owner's manual
This manual is also suitable for

Power Acoustik P3-15W is a high-performance subwoofer designed to deliver exceptional bass response and sound quality. With its 15-inch polypropylene injection-molded cone, butyl-rubber surround, and KSV Kapton voice coil, the P3-15W can handle up to 1200 watts RMS and produce a maximum power of 2800 watts. It features a dual 2-ohm voice coil configuration, allowing for various wiring options to achieve different impedance loads. The P3-15W is suitable for ported or sealed enclosures, with recommended volumes ranging from 2.00 to 4.00 cubic feet for ported and 1.25 to 2.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents