Power Acoustik OVN1-5500D Quick start guide

Brand: Power Acoustik

Model: OVN1-5500D

Category: Touch screen monitors

Type: Quick start guide

This manual is also suitable for

amplifiers

bamF series

2/4 Ch. Features

2 Ohm Stereo, 4 Ohm Bridged Stable Class A/B•

Tri-Mode Capable•

Variable 12dB 30-250Hz LPF•

Variable 12dB 50-500Hz HPF•

Variable 0-12dB 45Hz Bass Boost•

Variable 12 dB 15-50Hz Subsonic Filter •

(ex. 800/2 & 4ch. models)

Frequency Response: 10Hz - 30kHz•

Signal-to-Noise Ratio: 97dB•

Total Harmonic Distortion: .02%•

Dash Mount Remote Gain Control (2 ch. models)•

Sometimes you have to call them

like you see them; these full MOSFET

amplifiers will tear-up your ride

and bring out your inner beast. You

won’t have one seal left in your car

to keep water out! This is a

(B)ad (A)_ _ (M)other (F)letcher

BAMF Common Features

Die-Cast Aluminum Chassis•

Jet Black Texture Coat Finish•

Gloss Black Plexiglas Top•

Front Edge Pre-Amp and Connections•

Top Mounted Protection Indicator•

Chassis Integrated Mounting Feet•

All MOSFET Transistor Amplifier•

Regulated PWM Power Supply•

Three-Way Protection Circuitry •

(short, thermal & overload)

Hi/Low/Subsonic Crossovers•

Pre-Amp Outputs (ex. 1200/4)•

200mV-6V Low Level Inputs•

Direct Input 4 ga. Power & 8 ga. •

Speaker Terminals

Mono Block Features

1 Ohm Stable Class D•

Variable 12dB 40-200Hz LPF•

Variable 12dB 20-50Hz Subsonic Filter•

Variable 0-18dB 45Hz Bass Boost•

Frequency Response: 15-150Hz•

Signal-to-Noise Ratio: 100dB•

Total Harmonic Distortion: .5%•

180•

Phase Switch

Dash Mount Remote Gain Control•

Bridged Synchronization •

(strap amps together for double power!)

       

Model Chs. (watts) (watts) (watts) (watts) (2.125”h x 8.25”w) Included

BAMF2000/1D 1 600 900 1,200 2,000 11.375” Yes

BAMF4000/1D 1 1,200 1,700 2,200 4,000 13.75” Yes

BAMF5500/1D 1 1,700 2,500 3,200 5,500 16.875” Yes

       

Model Chs. (watts) (watts) (watts) (watts) (2.125”h x 8.25”w) Included

BAMF800/2 2 2 x 150 2 x 180 1 x 360 800 10.125” Yes

BAMF1250/2 2 2 x 220 2 x 280 1 x 560 1,250 11.375” Yes

BAMF1800/2 2 2 x 300 2 x 380 1 x 760 1,800 13.75” Yes

BAMF2200/2 2 2 x 370 2 x 450 1 x 900 2,200 15” Yes

BAMF2600/2 2 2 x 450 2 x 540 1 x 1,080 2,600 16.875” Yes

BAMF1200/4 4 4 x 100 4 x 125 2 x 250 1,200 11.875” No

BAMF1600/4 4 4 x 150 4 x 180 2 x 360 1,600 13.75” No

amplifiers

sTaX series

It’s tough to cram every desirable feature into one ampli-

fiers series. The STAX accomplished this. Heat-efficient

vertical cooling fins work better than horizontal fins

on this cast heatsink. All control are conveniently

located on one side making installations ultra clean.

The black acrylic top is reverseable so the wiring

can be in front or in back. To make these amps

even cooler, there are three 4 channels, three

2 channels and three monoblocks. There are

also 3 sizes of chassis, one of each size which

are all stackable! Any way you slice it, the

new STAX amps got it all…

2/4 Ch. Features

2 Ohm Stereo, 4 Ohm Bridged Stable Class A/B•

Tri-Mode Capable•

Variable 12dB 30-250Hz LPF•

Variable 12dB 50-500Hz HPF•

Variable 0-12dB 45Hz Bass Boost•

Variable 12 dB 15-50Hz Subsonic Filter (2 ch. models)•

Frequency Response: 10Hz - 30kHz•

Signal-to-Noise Ratio: 97dB•

Total Harmonic Distortion: .02%•

Dash Mount Remote Gain Control (2 ch. models)•



Stackable Chassis for Multiple Amplifier •

Applications

Die-Cast Aluminum Chassis•

Brilliant Silver Texture Coat Finish•

Gloss Black Plexiglas Top•

Front Edge Pre-Amp and Connections•

Top Mounted Protection Indicator•

Chassis Integrated Mounting Feet•

MOSFET PSU Transistors•

Regulated PWM Power Supply•

Three-Way Protection Circuitry •

(short, thermal & overload)

Hi/Low/Subsonic Crossovers•

Pre-Amp Outputs (ex. 1200/4)•

200mV-6V Low Level Inputs•

Direct Input 4 ga. Power & 8 ga. •

Speaker Terminals

Mono Block Features

1 Ohm Load Stable Class D•

Variable 12dB 40-200Hz LPF•

Variable 12dB 20-50Hz Subsonic Filter•

Variable 0-18dB 45Hz Bass Boost•

Frequency Response: 15-150Hz•

Signal-to-Noise Ratio: 100dB•

Total Harmonic Distortion: .5%•

180•

Phase Switch

Dash Mount Remote Gain Control•

Bridged Synchronization (strap amps •

together for double power!)

Model Chs. (watts) (watts) (watts) (watts) (2.125”h x 8.25”w) Included

BAMF2000/1D 1 600 900 1,200 2,000 11.375” Yes

BAMF4000/1D 1 1,200 1,700 2,200 4,000 13.75” Yes

BAMF5500/1D 1 1,700 2,500 3,200 5,500 16.875” Yes

Model Chs. (watts) (watts) (watts) (watts) (2.125”h x 8.25”w) Included

BAMF800/2 2 2 x 150 2 x 180 1 x 360 800 10.125” Yes

BAMF1250/2 2 2 x 220 2 x 280 1 x 560 1,250 11.375” Yes

BAMF1800/2 2 2 x 300 2 x 380 1 x 760 1,800 13.75” Yes

BAMF2200/2 2 2 x 370 2 x 450 1 x 900 2,200 15” Yes

BAMF2600/2 2 2 x 450 2 x 540 1 x 1,080 2,600 16.875” Yes

BAMF1200/4 4 4 x 100 4 x 125 2 x 250 1,200 11.875” No

BAMF1600/4 4 4 x 150 4 x 180 2 x 360 1,600 13.75” No

Model Chs. (watts) (watts) (watts) (watts) (2.125”h x 8.25”w) Included

       

       

       

Model Chs. (watts) (watts) (watts) (watts) (2”h x 9”w) Included

       

       

       

       

       

       

amplifiers

GOTHiC series

When something works so well, outperforms the com-

petition, and has done this for 10 years, you don’t mess

with it! All ya gotta do is just make it look awesome

again for current times. What else can we say, Gothic

amps are stickin’ and kickin’!

2/4 Ch. Features

2-ohm Stereo, 4-ohm Bridged Stable Class A/B•

Tri-Mode Capable •

Variable 12 dB 50-500Hz HPF (2 ch. models)•

Variable 12 dB 40-250Hz HPF ( 800 & 4 ch. models)•

Variable 12dB 30-500Hz LPF (2 ch. models)•

Variable 12 dB 40-250Hz LPF ( 800 & 4 ch. models)•

Variable 0-24dB 45Hz Bass Boost (2 ch. models)•

Variable 0-18dB 45Hz Bass Boost (800 & 4 ch. models)•

Variable 12 dB 30-175Hz Subsonic Filter (2 ch. models)•

Frequency Response: 10Hz - 30kHz•

Signal-to-Noise Ratio: 98dB•

Total Harmonic Distortion: .02%•

4 ga. Power & 8 ga. Speaker Terminals•

Dash Mount Remote Gain Control (2 ch. models)•

Gothic Common Features

Extruded Aluminum Chassis•

Gunmetal Grey Anodized Finish w/ •

Chrome Accents

MOSFET PSU Transistors•

Regulated PWM Power Supply•

Three-Way Protection Circuitry •

(short, thermal & overload)

Hi/Low/Subsonic Pass Crossovers•

Pre-Amp Outputs•

200mV-8V Low Level Inputs•

Direct 4 ga. Power & 8 ga. Speaker •

Terminals

Mono Block Features

1 Ohm Load Stable Class D•

Variable 12dB 40-200Hz LPF•

Variable 12dB 20-50Hz Subsonic Filter•

Variable 0-18dB 45Hz Bass Boost•

Frequency Response: 15-150Hz•

Signal-to-Noise Ratio: 100dB•

Total Harmonic Distortion: .5%•

180•

Phase Switch

Dash Mount Remote Gain Control•

Bridged Synchronization (strap amps •

together for double power!)

Mono Block       

Model

Chs. (watts) (watts) (watts) (watts) (3”h x 10.625”w) Included

OVN1-2000D 1 600 900 1,200 2,000 10.875” Yes

OVN1-3000D 1 900 1,300 1,700 3,000 12.875” Yes

OVN1-4000D 1 1,200 1,700 2,200 4,000 14.875” Yes

OVN1-5500D 1 1,700 2,500 3,200 5,500 19.125” Yes

2/4 Ch.       

Model Chs. (watts) (watts) (watts) (watts) (3”h x 10.625”w) Included

OVN2-600 2 2 x 95 2 x 120 1 x 240 600 8.125” No

OVN2-800 2 2 x 150 2 x 180 1 x 360 800 10.875” Yes

OVN2-1250 2 2 x 220 2 x 280 1 x 560 1,250 12.875” Yes

OVN2-1800 2 2 x 300 2 x 380 1 x 760 1,800 14.875” Yes

OVN2-2200 2 2 x 370 2 x 450 1 x 900 2,200 20.375” Yes

OVN4-840 4 4 x 80 4 x 95 2 x 190 840 10.875” No

OVN4-1200 4 4 x 100 4 x 125 2 x 250 1,200 12.875” No

OVN4-1600 4 4 x 150 4 x 180 2 x 360 1,600 18” No

You asked for the “Best bang for the buck” we delivered it, in the all new Crypt

line of amplifiers. This new chassis design incorporates new assembly tech-

niques and shear volume production without sacrificing power and sound

quality. We learned some new circuit tricks that will deliver bone shattering

power at even lower prices from our previous versions. The kids will love the

new “Dead Look” with skulls to match! Who doesn’t have tattoo’s these days

that are skull and crossbones. We have included all the most popular fea-

tures in this exciting new line-up including complimentary Class “D” amplifiers

to match. This new series will drive them crazy.

Everyone loves a little skull now and then!

amplifiers

CrypT series

2/4 Ch. Features

2-ohm Stereo, 4-ohm Bridged Stable Class A/B•

Tri-Mode Capable •

Fixed HPF 80Hz (2ch. models )•

Variable 12dB 50-250Hz HPF (4ch. models)•

Variable 12dB 50-250Hz LPF•

Selectable 45Hz, 6/12dB Bass Boost •

Frequency Response: 10Hz - 20kHz•

Signal-to-Noise Ratio: 90dB•

Total Harmonic Distortion: .01%•

4 ga. Power & 8 ga. Speaker Terminals•

Crypt Common Features

Extruded Aluminum Chassis•

Black Texture Finish w/ Silver Trim & •

Cast Metal Badge

MOSFET PSU Transistors•

Regulated PWM Power Supply•

Three-Way Protection Circuitry (short, •

thermal & overload)

High Pass, Low Pass, and Subsonic •

Filters

Pre-Amp Outputs•

200mV-8V Low Level Inputs•

4 ga. Power & 8 ga. Speaker Terminals•

Mono Block Features

1 Ohm Load Stable Class A/B or D•

Variable 12dB 50-250Hz HPF (1400 & 1900)•

Variable 12dB 50-250Hz LPF•

Variable 12dB 20-50Hz Subsonic Filter (Class D)•

Selectable 45Hz, 6/12dB Bass Boost •

Freqency Response: 15-150Hz•

Signal-to-Noise Ratio: 80dB•

Total Harmonic Distortion: .5%•

180•

Phase Switch (Class D)

Direct 2 ga. Power & 8 ga. Speaker Terminals•

Dash Mount Remote Gain Control•

Bridged Synchronization (strap amps together for •

double power!)

2/4 Ch. No. Chs. RMS @ 4Ω RMS @ 2Ω Bridged @ 4Ω MAX Power Length (in): Bass Knob

Model (watts) (watts) (watts) (watts) 2.3” h x 9.8” w Included

CPT2-400 2 2 x 80 2 x 100 1 x 200 400 9” No

CPT2-600 2 2 x 100 2 x 125 1 x 250 600 11” No

CPT2-900 2 2 x 150 2 x 200 1 x 400 900 13” No

CPT2-1500 2 2 x 250 2 x 325 1 x 650 1,500 15” No

CPT4-800 4 4 x 80 4 x 100 2 x 200 800 13” No

CPT4-1200 4 4 x 100 4 x 125 2 x 250 1,200 14” No

CPT4-1400 4 4 x 120 4 x 150 2 x 300 1,400 15” No

CPT4-1700 4 4 x 150 4 x 190 2 x 380 1,700 17” No

Model

Chs. (watts) (watts) (watts) (watts) (3”h x 10.625”w) Included

OVN1-2000D 1 600 900 1,200 2,000 10.875” Yes

OVN1-3000D 1 900 1,300 1,700 3,000 12.875” Yes

OVN1-4000D 1 1,200 1,700 2,200 4,000 14.875” Yes

OVN1-5500D 1 1,700 2,500 3,200 5,500 19.125” Yes

Model Chs. (watts) (watts) (watts) (watts) (3”h x 10.625”w) Included

OVN2-600 2 2 x 95 2 x 120 1 x 240 600 8.125” No

OVN2-800 2 2 x 150 2 x 180 1 x 360 800 10.875” Yes

OVN2-1250 2 2 x 220 2 x 280 1 x 560 1,250 12.875” Yes

OVN2-1800 2 2 x 300 2 x 380 1 x 760 1,800 14.875” Yes

OVN2-2200 2 2 x 370 2 x 450 1 x 900 2,200 20.375” Yes

OVN4-840 4 4 x 80 4 x 95 2 x 190 840 10.875” No

OVN4-1200 4 4 x 100 4 x 125 2 x 250 1,200 12.875” No

OVN4-1600 4 4 x 150 4 x 180 2 x 360 1,600 18” No

Mono Block No. Chs. RMS @ 4Ω RMS @ 2Ω RMS @ 1Ω MAX Power Length (in): Bass Knob

Model (watts) (watts) (watts) (watts) 2.3” h x 9.8” w Included

CPT1-1500 1 500 650 - 1,500 13” Yes

CPT1-2000 1 670 870 - 2,000 15” Yes

CPT1-2200D 1 700 950 1,300 2,200 12” Yes

CPT1-3200D 1 1,000 1,400 1,800 3,200 13” Yes

CPT1-4000D 1 1,200 1,700 2,200 4,000 16” Yes

CPT1-5500D 1 1,700 2,500 3,200 5,500 19” Yes

NEW

When technology advances, products do as well. Does Lamborghini need to refine their cars

every 2 years? NO, they do because they can. After 6 years, it is time for a change. Say “See

Ya!” to the old MOFO, and please welcome the new MOFO-X subwoofers! The new motor is

refined and increases efficiency dramatically! MOFO-X subs use a composite sandwich cone

with a polypropylene surface for durability and Spruce pulp backing for smooth low bass.

Like the original MOFOs, the new models still use an aluminum dustcap that couples to the

voice coil former and extends over the cone. Why? The fins brace the cone and eliminate

cone flex during high excursion. And since they are aluminum and couple to the dust cap

and coil former, they act as a heat sink or heat extractor. Using the latest materials, the new

MOFO subs yield superior performance. Cast aluminum baskets? Of course! Increased bot-

tom octave output? You bet! Louder than the original design? Duh!

subwoofer

mOFO series

COMMON FEATURES

Model

Power Power Motor Fs Qms Vas Xmax Qes Qts Efficiency Mounting Cutout Sealed Ported Port

MAX RMS Weight (Hz) (ft3) (mm) (dB) Depth (in) Dia. (in) (ft3) (ft3) (dia. x L)

MOFO-122X 2,700 1,500 373oz 28.92 5.559 1.367 25 0.429 0.399 85 6.875” 11.25” 1.00 2.00 4” x 12”

MOFO-152X 3,000 1,700 373oz 24.07 6.103 3.761 25 0.48 0.445 87 8.125” 14.125” 2.00 4.00 (2) 4” x 11.75”

2.5” Dual 2-Ohm 4-Layer Voice Coil

•

Royal Blue Finish w/ Diamond Cut Accents •

Die Cast Aluminum Voice Coil Heatsink •

Non-Pressed Pulp Cone •

Polyether Foam Surround •

Nickel Plated 8ga Compression Wire Terminals •

Dual Poly-Cotton Spiders •

Die-Cast Aluminum Frame •

Vented Pole Piece •

NEW

Many vehicles do not have tons of space available for a big, bulky enclosure. Some

vehicle, like some crew-cab trucks, have no space for a subwoofer. Until now… The

THIN-13 is now the shallowest woofer on the market! Coming in at a mere 2” of depth,

they will fit behind rear crew-cab truck seats, under many front seats, or even in a

friggin’ door with some custom fabrication! While other “shallow mount” subwoofers

are available, they typically require traditional airspace. The THIN-13 is 13.25” in diam-

eter and not only does it play well in 1 cubic foot (typical for most 8”-10” woofers),

but it reproduces lower frequency response than most 12” woofers in much larger

enclosures. No more whining about not having a subwoofer available that will fit in

virtually every vehicle! THIN-13 has you covered…

Model

Power Power Motor Fs Qms Vas Xmax Qes Qts Efficiency Mounting Cutout Sealed Ported Port

MAX RMS Weight (Hz) (ft3) (mm) (dB) Depth (in) Dia. (in) (ft3) (ft3) (dia. x L)

MOFO-122X 2,700 1,500 373oz 28.92 5.559 1.367 25 0.429 0.399 85 6.875” 11.25” 1.00 2.00 4” x 12”

MOFO-152X 3,000 1,700 373oz 24.07 6.103 3.761 25 0.48 0.445 87 8.125” 14.125” 2.00 4.00 (2) 4” x 11.75”

FEATURES

 

 

 

 

 

 

 

 

subwoofer

THiN-13

Model Power Magnet Fs Qms Vas Xmax Qes Qts Efficiency Mounting Cutout Sealed

(watts) Weight (Hz) (ft3) (mm) (dB) Depth (in) Dia. (in) (ft3)

THIN-13 700 31 oz. 30.0 4.304 0.870 9.0 0.973 0.794 78.80 2” 11.375” 0.75

CHECK THIS OUT!

We took the gift box and beefed it up to ¼1/8” thick. The sub played flat all

the way down to the subsonic range! There’s NO other woofer that can do

this!! Ya gotta hear it to believe it…

STEALTH-13BX

.6 cubic foot Preloaded Enclosure

•

Carpeted Grey w/ Embroidered Accents

•

30 x 14.5 x 5.25/2.25

•

THIN-13BX Preloaded Enclosure

2”

subwoofer

psQ series

In past years, square, triangular, hexagonal and

pentagonal subwoofers have tried to change &

excite the marketplace. The very simple fact is

that if you have any given area, a square woofer

will yield the most cone area which means higher

SPL. Even so, most square woofers have been

poorly designed and do not meet the expecta-

tions. The PSQ subwoofers are engineered from

the ground up, and do yield higher SPL than any of

our other subwoofers!

28% More Cone Area Than Round Woofer•

Stamped Steel Basket w/ Rolled Edges•

Aluminum Voice Coil Former•

Direct Wire Terminal Design•

Injection Molded Polypropylene Dust Cap•

Silver Polypropylene Cone•

Multi-Roll NBR Rubber Surround•

Vented Back Plate•

Suspension Integrated Tinsel Leads•

DVC4 Ohm•

COMMON FEATURES

Model Power Power Magnet Fs Qms Vas Xmax Qes Qts Efficiency Mounting Cutout Sealed Ported Port

MAX RMS Weight (Hz) (ft3) (mm) (dB) Depth (in) Sq. (ft3) (ft3) (dia. x L)

PSQ-10 1,800 700 82 oz. 34.9 5.000 1.314 15.0 0.800 0.690 85.00 7.125” 9.25” 1.25 1.75 4” x 12.5”

PSQ-12 1,800 700 82 oz. 30.7 5.000 2.917 15.0 0.923 0.779 86.18 7.375” 11.125” 2.00 2.50 4” x 10”

28% More Cone Area Than Round Woofer

Model Power Power Magnet Fs Qms Vas Xmax Qes Qts Efficiency Mounting Cutout Sealed Ported Port

MAX RMS Weight (Hz) (ft3) (mm) (dB) Depth (in) Sq. (ft3) (ft3) (dia. x L)

PSQ-10 1,800 700 82 oz. 34.9 5.000 1.314 15.0 0.800 0.690 85.00 7.125” 9.25” 1.25 1.75 4” x 12.5”

PSQ-12 1,800 700 82 oz. 30.7 5.000 2.917 15.0 0.923 0.779 86.18 7.375” 11.125” 2.00 2.50 4” x 10”

subwoofer

p3 series

Being the biggest brother in the new family

of drivers requires even better parts and the

ability to meet expectations. Adding Conex

spiders and larger Polyester-Imide enam-

eled copper voice coils wrapped on Kapton

formers are the requirements for higher

power handling, better heat dissipation, and

sonic quality. If you are the type of person

who likes their face smacked against the

dash due to insane amounts of bass, step

up to the big boys!

Polypropylene Injection Molded Cone•

Butyl-Rubber Surround•

•

Nickel Plated Compression 8 ga. Wire Terminal•

Poly Cotton Spider•

Texture Coat Finish on Stamped Steel Basket•

Suspension Intergrated Tinsel Leads•

DVC2 Ohm•

COMMON FEATURES

Model Power Power Magnet Fs Qms Vas Xmax Qes Qts Efficiency Mounting Cutout Sealed Ported Port

MAX RMS Weight (Hz) (ft3) (mm) (dB) Depth (in) Dia. (in) (ft3) (ft3) (dia. x L)

P3-10W 2,000 800 120oz. 29.6 7.115 1.100 29.0 0.648 0.594 82.85 6.5” 9.25” 0.75 1.50 3” x 9”

P3-12W 2,600 1000 150oz. 30.6 9.803 1.567 34.5 0.966 0.879 83.06 6.75” 11” 1.25 2.00 4” x 12.5”

P3-15W 2,800 1200 180oz. 24.9 7.707 5.277 34.5 0.772 0.702 86.61 7.75” 14” 2.00 4.00 (2 ) 4” x 11.75”

Polypropylene Injection Molded Cone•

Butyl-Rubber Surround•

•

Nickel Plated Compression 8 ga. Wire Terminal•

Poly Cotton Spider•

Texture Coat Finish on Stamped Steel Basket•

Suspension Intergrated Tinsel Leads•

DVC4 Ohm•

subwoofer

p2 series

Taking performance to the next level, these new subs have some dras-

tic improvements. Being redesigned from the ground up gives us the

opportunity to tailor the final product to what you’ve been asking for.

You asked for more power handling – you got it! You wanted more

bottom-end low bass – you got it! More importantly, these new subs

are more durable and will last longer than previous models. All of this is

due to the Kapton formers with copper wound voice coils, butyl rubber

surrounds, polypropylene cones, and above all, proper design.

COMMON FEATURES

Model Power Power Magnet Fs Qms Vas Xmax Qes Qts Efficiency Mounting Cutout Sealed Ported Port

MAX RMS Weight (Hz) (ft3) (mm) (dB) Depth (in) Dia. (in) (ft3) (ft3) (dia. x L)

P2-10W 1,200 500 110oz. 33.5 5.625 1.235 22.2 0.782 0.691 84.10 6.5” 9.25” 0.75 1.50 3” x 9”

P2-12W 1,400 600 120oz. 24.8 5.176 3.017 28.2 0.837 0.720 83.80 6.75” 11” 1.25 2.00 4” x 12.5”

P2-15W 1,600 700 140oz. 22.2 5.939 8.041 29.0 0.653 0.588 87.68 7.75” 14” 2.00 4.00 (2) 4” x11.75”

PEN-12W

Model Power Power Magnet Fs Qms Vas Xmax Qes Qts Efficiency Mounting Cutout Sealed Ported Port

MAX RMS Weight (Hz) (ft3) (mm) (dB) Depth (in) Dia. (in) (ft3) (ft3) (dia. x L)

P2-10W 1,200 500 110oz. 33.5 5.625 1.235 22.2 0.782 0.691 84.10 6.5” 9.25” 0.75 1.50 3” x 9”

P2-12W 1,400 600 120oz. 24.8 5.176 3.017 28.2 0.837 0.720 83.80 6.75” 11” 1.25 2.00 4” x 12.5”

P2-15W 1,600 700 140oz. 22.2 5.939 8.041 29.0 0.653 0.588 87.68 7.75” 14” 2.00 4.00 (2) 4” x11.75”

subwoofer

p1 series

Subwoofers do not need to have monster

magnets to work properly. These all-new

drivers are great for the modest powered

system and yield great sound quality and

much lower bass than the previous mod-

els. Each model features a molded Polypro-

pylene cone and Butyl Rubber surround for

great performance and durability. Dual 4-ohm

voice coils are wound on Kapton formers for

versatility and better heat dissipation. Check

out the new entry level drivers and see for

yourself that lost cost subs do not have to

sacrifice performance!

Polypropylene Injection Molded Cone•

Butyl-Rubber Surround•

•

Nickel Plated 8 ga. Compression Wire Terminal•

Poly Cotton Spider•

Texture Coat Finish on Stamped Steel Basket•

Suspension Intergrated Tinsel Leads•

DVC4 Ohm•

COMMON FEATURES

Model Power Power Magnet Fs Qms Vas Xmax Qes Qts Efficiency Mounting Cutout Sealed Ported Port

MAX RMS Weight (Hz) (ft3) (mm) (dB) Depth (in) Dia. (in) (ft3) (ft3) (dia. x L)

P1-10W 700 300 70oz. 34.8 6.318 1.368 21.1 1.092 0.931 83.63 4.875” 9.25” 0.75 1.50 3” x 9”

P1-12W 900 400 70oz. 28.3 7.175 2.362 24.0 0.900 0.800 84.11 5.125” 11” 1.25 2.00 4” x 12.5”

P1-15W 1,000 500 80oz. 24.8 6.025 7.329 24.0 0.904 0.786 87.29 6.375” 14” 2.00 4.00 (2) 4” x11.75”

subwoofer

peN series

4 Ohm 12” Subwoofer•

•

Gloss Black Finish on Stamped Steel Basket •

Pressed Paper Cone•

Butyl-Rubber Surround•

2” 4-Ohm 4-Layer ASV Voice Coil•

Quick Disconnect Wire Terminal•

Poly-Cotton Spider•

40oz Magnet w/ Vented Back Plate•

Laser Etched Logo on Poly Dust Cap•

tweeters

NB-1 2-Way Mount Tweeter 200 Watts

 

 

 

 

 

 

 

 

 

NB-2 3-Way Mount Tweeter 200 Watts

 

Transducer Magnet

 

 

 

 

 

 

 

NB-4 4-Way Mount Tweeter 250 Watts

 

 

 

 

 

 

 

NX-5 (PAIR) Bullet Tweeter 200 Watts

 

 

 

 

 

 

 

 

 

NX-6 Horn Tweeter 200 Watts

 

 

 

 

 

 

 

 

XP2K-60C 6.5” Electro-Plated Injection Molded Cone Mid-Bass

component

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

KP-60C 6.5” 200 watts component system

Woofer



Brush Steel Finish



20 oz. High Density Ferrite Ring Magnet W/ Rubber Boot



FEA T-Motor Design for Linear Flux Saturation to Lower Distortion



Injection Poly Cone W/ Electro-plated Brush Black Chrome Surface



NBR Rubber Surround Compliant W/ Black Progressive Roll Spider



Copper Wire Coil on 1” Aluminum Former W/ Reinforced Neck Joint

Tweeter



Custom Tooled Injection ABS Tweeter Multi Function Mounting Set



0.8” High Density N40 Neodymium Disc Magnet



FEA U-Motor Design for Linear Flux Saturation to Lower Distortion



PEN Dome and Silk Surround For Brighter Sound Performance



Copper Wire coil on 1” Aluminum Former W/ Soldered Lead Wire

X-Over



Single Side PCB and High Quality Soldering



Injection ABS Casing W/ Dual Side Placement Terminals



Natural Woofer Slope for Phase Correct Output



12dB Tweeter Slope W/ +3/0/-3dB Efficiency Attenuation

midrange

NB-2 3-Way Mount Tweeter 200 Watts

MID-65 Midrange/Bass Driver 300 Watts

 

 

 

 

 

 

 

XPS-104 4” Midrange

 

 

 

 

 

 

speakers

Xp series

XP2K-465P 4” x 6” 2-Way Component Plate 140 Watts

 

 

 

 

 

 

 

 

 

 

Black Texture Coat Stamped Steel Frame•

Chrome Back Plate•

Poly Propylene Injection Cone•

Butyl Rubber Surround•

3-Ohm Impedance•

•

.75" Silk Tweeter•

•

XP-694K 6”x9” 4-Way 420 Watts

XP-653K 6.5” 3-Way 250 Watts

XP-502K 5.25” 2-Way 200 Watts

XP-402K 4” 2-Way 180 Watts

       

Size & Type 6x9 4-way 6.5" 3-way 5.25" 2-way 5" x 7" 3-way 4" x 6" 2-way 4" 2-way 4" x 10" 3-way

Power Handling (watts) 420 250 200 270 200 180 270

Magnet Weight (oz) 20 10 10 10 5.3 5.3 10

Frequency Response (Hz) 45-20kHz 65-20kHz 80-20kHz 65-20kHz 100-20kHz 100-20kHz 65-20kHz

Efficiency (dB) 90 89 88 88 86 86 88

Top Mount Depth (in) 3.125" 2.125" 2.125" 2.25" 1.75" 1.875" 2.5"

Bottom Mount Depth (in) 3.5" 2.375" 2.375" 2.625" 2" 2.125" 3"

Cutout Dimension (in) 5.875" x 8.625" 4.875" 4.5" 5" x 7" 3.5" x 5.625" 3.625" 3.75" x 9.375"

Overall Dimension (in) 6.5" 6.25" 5.125" 5.5" x 7.5" 3.875" x 6" 4" 4.375" x 9.875"

XP-573K 5” x 7” 3-way 270 Watts

XP-462K 4” x 6” 2-way 200 Watts

XP-4103K 4” x 10” 3-way 270 Watts

KP-52N 5.25” 2 Way Speakers 180 Watts

KP-42N 4” 2 Way Speakers 160 Watts

KP-462N 4”x6” 2 Way Speakers 180 Watts

KP-573N 

KP-69 6”x9” 3 way speakers 360 watts

KP-65 6.5” 2Way Speakers 200 Watts

Polypropylene Injecteion Cone•

Butyl Rubber Surround•

Stamped Steel Frame•

Copper Voice Coil on Aluminum Former•

3-Ohm Impedance•

2” Polymide Midrange (694N)•

1.125” Polymide Tweeter•

.5” Polymide Super Tweeter (653N & 573N)•

NEW

       

Size & Type 6x9 4-way 6.5" 3-way 5.25" 2-way 5" x 7" 3-way 4" x 6" 2-way 4" 2-way 4" x 10" 3-way

Power Handling (watts) 420 250 200 270 200 180 270

Magnet Weight (oz) 20 10 10 10 5.3 5.3 10

Frequency Response (Hz) 45-20kHz 65-20kHz 80-20kHz 65-20kHz 100-20kHz 100-20kHz 65-20kHz

Efficiency (dB) 90 89 88 88 86 86 88

Top Mount Depth (in) 3.125" 2.125" 2.125" 2.25" 1.75" 1.875" 2.5"

Bottom Mount Depth (in) 3.5" 2.375" 2.375" 2.625" 2" 2.125" 3"

Cutout Dimension (in) 5.875" x 8.625" 4.875" 4.5" 5" x 7" 3.5" x 5.625" 3.625" 3.75" x 9.375"

Overall Dimension (in) 6.5" 6.25" 5.125" 5.5" x 7.5" 3.875" x 6" 4" 4.375" x 9.875"

kp series

KP-694N 6”x9” 4 way speakers 380 watts

KP-653N 6.5” 3 Way Speakers 220 Watts

        

Size & Type 6”x9” 4-way 6”x 9” 3-way 6.5” 3-way 6.5” 2-way 5.25” 2-way 4” 2-way 4” x 6” 2-way 5” x 7” 3-way

Power Handling (watts) 380 360 220 200 180 160 180 240

Magnet Weight (oz) 20oz. 25oz. 10oz. 5.4oz. 10oz. 10oz. oz.5.3 5.3oz.

Frequency Response (Hz) 45-20kHz 60-20kHz 65-20kHz 70-20kHz 80-20kHz 100-20kHz 100-20kHz 65-20kHz

Efficiency (dB) 90dB 92dB 89dB 92dB 87dB 87dB 87dB 89dB

Top Mount Depth (in) 3.25” 3” 2.125” 1.75” 2” 1.875” 1.75” 2.125”

Bottom Mount Depth (in) 3.75” 3.5” 2.375” 2” 2.25” 2” 2” 2.5”

Cutout Dimension (in) 6” x 8.75” 6” x 8.75” 4.875” 5.5” 4.5” 3.625” 3.5” x 5.75” 5” x 7”

Overall Dimension (in) 6.5” x 9” 6.5” x 9.25” 6.25” 6.5” 5.125” 4” 3.875” x 6” 5.5” x 7.5”

speakers













4.5 MILLIOHM INT. RESISTANCE

2.5 AMP/HOUR

































































CAPCELL-800 800 Amp CAPCELL

capcell

TO CAP OR TO CELL… THAT IS THE QUESTION!

After years of large capacitors being on the market, they still remain a mystery to many…

Often called a “power cap” or “stiffening cap”, some people prefer caps over adding a second battery and vice versa. So, which product

is a smarter choice? NEITHER!

A second battery is a great option for high power systems, but should be accompanied by an upgraded alternator that can efficiently

charge both batteries. This can get really expensive.

A capacitor is similar to a battery but can charge and discharge in a fraction of a second depending on size. The cap has the ability to

empty itself almost instantly on transient notes in music material. However, it does not have the stamina that a battery has and is not

an equivalent substitute.

Our Cap Cells are a fusion of both products. The Cap Cell offers auxiliary power with the ability to enhance the transient notes, often

suppressed in car audio systems with an OEM battery, while being able to reinforce the battery during long, intense bass notes. A

second alternator is not necessary, making the Cap Cell a perfect addition and an affordable way to supply the necessary power for

a system.

CAPCELL-300 300 Amp CAPCELL

CAPCELL-400 400 Amp CAPCELL

CAPCELL-600 600 Amp CAPCELL

PC1.5F 1.5 Farad Digital Power Capacitor

 

 

 

 

 

 

 

capacitors

PC2.0F 2 Farad Digital Power Capacitor

 

 

 

 

 

 

 

 

PCX-3F 3 Farad Digital Power Capacitor



















PCX-5F 5 Farad Digital Power Capacitor

PCX-10F 10 Farad Hybrid Digital Power Capacitor

PCX-20F 20 Farad Hybrid Digital Power Capacitor























PCX-30F 30 Farad Hybrid Digital Power Capacitor

signal processor

BASS-10

 

 

 

 

 

 

 

 

 

 

 

 

 

BASS-12

 

 

 PFM Subsonic Filter & Bass Level Control

 Illuminated Logo Plate

 Chrome Finish

 

 

 

 

 

 

 

 

 THD: 0.002%

 S/N Ratio: 132dB

 

PWM-20 Four Band Parametric EQ

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PWM-70 7 band parametiric Equalizer

C-1B Active 12 dB Crossover















C-3184 3-Way Electronic Crossover

 

 

 

Low/High Pass Sections

 

  

Frequency Extender (3x, 5x)

 

 

 

 

 

 

C-30XR 

 

 

 

 

 

 

 

 

 

at 40 to 120 Hz (Variable)

 

 

signal processor

PWM-19 Four band Parametric EQ

 

 

 

 

 

 

 

 

 

 

 

 

 

PWM-16 Four band Parametric EQ

 

 

 

 

 

 

 

 

 

 

 

 

amp wire kits

Attaches to Existing Factory Mirror by Spring Loaded Clips or Straps•

4.3” TFT-LCD Swiveling Touch Screen •

Built-in GPS Turn-by-Turn Navigation•

WinCE 5.0 GPS Operating System•

SiRF Star-3 Chip-set•

28 GPS Receiving Channels•

GPS Receiving Antenna Included•

Bluetooth 2.0 for Hands-Free Calling •

A2DP Streaming Mp3 Playback from Enabled Smart Phone•

Built-in Speaker for Mp3 Playback & Navigation Commands•

On-Board Rechargeable Lithium Battery•

•

A/V Inputs for Auxiliary Source•

Audio Outputs for Systems Integration•

Rear View Camera Input w/ Trigger•

Built-in FM Transmitter•

Cigarette Lighter Charger•

480 x 272 Screen Resolution•

400 NIT Brightness•

Universal Clip-on Rear-View Mirror w/ Navigation, Bluetooth & 4.3” Touch Screen

MNAV-43B

AKIT-2

17ft 2ga Matte Blue Power Wire•

3ft 2ga Matte Clear Power Wire•

30ft 12ga Matte Blue & Matte Clear Twisted Pair Speaker Wire•

17ft 18ga Matte Blue & Matte Clear Twisted Pair RCA Interconnects•

17ft Matte Blue Remote Turn-On Wire•

80A ANL Fuse & Holder•

Complete Installation Accessories•

AKIT-4

17ft 4ga Matte Blue Power Wire•

3ft 4ga Matte Clear Power Wire•

25ft 12ga Matte Blue & Matte Clear Twisted Pair Speaker Wire•

17ft Matte Blue & Matte Clear Twisted Pair RCA Interconnects•

17ft Matte Blue Remote Turn-On Wire•

60A Maxi Fuse & Holder•

Complete Installation Accessories•

AKIT-8

17ft 8ga Matte Blue Power Wire•

3ft 8ga Matte Clear Power Wire•

25ft 16ga Matte Blue & Matte Clear Twisted Pair Speaker Wire•

17ft 18ga Matte Blue & Matte Clear Twisted Pair RCA Interconnects•

17ft Matte Blue Remote Turn-On Wire•

40A Maxi Fuse & Holder•

Complete Installation Accessories•

Areyoutiredoflickingyourgpssuctioncupmounttostickittothewindshieldorre-positioningyouraftermarketbeanbagmountthat’sslidingaroundyou

dash-board?Yourotheroptionwastouseanairconditionerclipthatnowblocksyourcoolairow.Nowlet’slookattheoptionofthepushbuttondirections

oeredbyanamericanmanufacturer,whentheyaskyoutopullovertogetdirectionswithamonthlyfeethatwillbreakthebankandstillfrustrateyousince

youhavetowritethedirectionsdown…!Wehavethemostconvenientsolutionwithournewclip-on4.3”Hi-resolutionrearviewmirrormountnavigation

systemwithnavteqmappingandlighteningfastwince5.0Operatingsystem,andthelatestsirfstar-3chipsolution.Don’tforget12millionpointsofinterest.

Thisputsyourmapviewingatamoreconvenientposition.Nowaddotherfeatureslikeback-upcamerainput,mp-3playbackviaa2dpforpda’s,orusethe

onboardsdcardreader(readscardsto16gig.)Foryourpre-recordedmedia.Nowallyouhavetoisdialyourfmreceivertoonboardfmtransmitterfrequencies

(88.3~89.1)Tolistenyourfavoritesourcematerial.

Nowthat’swhatwecallasolutiontomediaintegration!

Page is loading ...