MasterCraft 057-4587-6 User manual

Brand: MasterCraft

Model: 057-4587-6

Category: Laser levels

Type: User manual

INSTRUCTION MANUAL

SELF-LEVELLING CROSS-LINE

LASER LEVEL

057-4587-6

SELF-LEVELLING CROSS-LINE LASER LEVEL - 057-4587-6

TABLE OF CONTENTS

If any parts are missing

or damaged, or if you have any

questions, please call

our toll-free helpline at

1-800-689-9928.

Read and understand this instruction manual

thoroughly before using the product. It contains

important information for your safety as well

as operating and maintenance advice.

Keep this instruction manual for future use.

Should this product be passed on to a third

party, then this instruction manual must be

included.

TECHNICAL SPECIFICATIONS 3

SAFETY GUIDELINES 4–6

DESCRIPTION 7

OPERATING INSTRUCTIONS 8–14

MAINTENANCE 15

TROUBLESHOOTING 16

PARTS LIST 17–19

WARRANTY 20–21

SELF-LEVELLING CROSS-LINE LASER LEVEL - 057-4587-6

SAFETY GUIDELINES

TECHNICAL SPECIFICATIONS

POWER SUPPLY 3V (2 x 1.5V AA

alkaline batteries)

OPERATING RANGE 10 m

ACCURACY ±1 mm/m

LASER DIODE TYPE 650 nm, maximum power

output ≤1 mW

LASER CLASS Class II

LEVELLING RANGE ±4°

SELF-LEVELLING TIME Approx. 6 sec.

BATTERY LIFE 15 hours (with new

alkaline batteries)

OPTIMUM OPERATION

TEMPERATURE 0°C–40°C (32°F–104°F)

WEIGHT

(WITHOUT BATTERIES) 7.4 oz (210 g)

Know your self-levelling cross-line laser level

Before using this self-levelling cross-line laser level, read this Instruction Manual carefully.

Keep this Manual in a safe place for future reference.

Important

This device should only be serviced by a qualiﬁed service technician. For more information, call

the toll-free helpline at 1-800-689-9928.

Read all instructions thoroughly

Save these instructions

DANGER!

People with electronic devices, such as pacemakers, should consult their

physician(s) before using this product. Operation of electrical equipment in close

proximity to a heart pacemaker could cause interference or failure of the pacemaker.

WARNING!

Be sure to read and understand all instructions in this manual before using this

product. Failure to follow all instructions may result in hazardous radiation exposure,

electric shock, and/or bodily injury.

WARNING!

To reduce the risk of injury, the user must read and understand the Instruction

Manual before using this product.

WARNING!

Use of controls, adjustments, or the performance of procedures other than those

speciﬁed in this manual may result in hazardous radiation exposure.

WARNING!

The use of optical instruments such as, but not limited to, telescopes or transits to

view the laser beam will increase eye hazard.

CAUTION!

Do not attempt to modify the performance of the laser device in any way. This may

result in a dangerous exposure to laser radiation.

SELF-LEVELLING CROSS-LINE LASER LEVEL - 057-4587-6

SAFETY GUIDELINES

This self-levelling cross-line laser level has a built-in laser light. The laser is Class II and emits

output power of a maximum 1 mW and 650 wavelengths. These lasers do not normally present

an optical hazard. However, do not stare at the beam, as this can cause ﬂash blindness.

The following labels are on your tool. They indicate the

location from which the laser level emits the laser light.

Always be aware of the laser light location when using the

tool. Always make sure that any bystanders in the vicinity

of use are made aware of the dangers of looking directly

into the laser.

WARNING!

LASER RADIATION. DO NOT STARE INTO

BEAM. Class II laser product. Turn the laser

beam on only when using this tool.

• Do not remove or deface any product labels.

• Avoid direct eye exposure. The laser beam can cause

ﬂash blindness.

• The laser level is not a toy. Always keep it out of the

reach of children. The laser light emitted from this tool should never be directed toward

any person for any reason.

• Do not operate the tool around children or allow children to operate the tool.

• Do not place the tool in a position that may cause anyone to stare at the laser

beam, whether intentionally or unintentionally.

• Do not use on surfaces such as sheet steel that have shiny, reﬂective surfaces. The

reﬂective surface could reﬂect the beam back at the operator.

• Always turn the laser tool off when not in use. Leaving the tool on increases the risk of

someone inadvertently staring into the laser beam.

• Do not attempt to repair or disassemble the self-levelling cross-line laser level.

If unqualiﬁed persons attempt to repair this product, serious injury may occur. Any repair

required on this laser product should be performed only by authorized service personnel.

• Do not operate the tool in combustible areas, such as in the presence of ﬂammable

liquids, gases, or dust.

• Use of other accessories that have been designed for use with other laser tools

could result in serious injury.

• Keep batteries out of reach of children.

• Save these instructions. Refer to them frequently and use them to instruct others who

may use this tool. If you loan this tool to someone else, also loan these instructions to them to

prevent misuse of the product and possible injury.

SAFETY GUIDELINES

MADE IN CH INA/FABRIQUÉ EN CHINE IMPORTED BY/IMPORTÉ PAR

MASTERCRAFT CANADA TORONTO, CANADA M4S 2B8

057-4587-6

SELF-LEVELLING CROSS-LINE

LASER LEVEL

NIVEAU AU LASER À FAISCEAUX

CROISÉS AUTONIVELANT

3V 2×1.5 V AA Battery

3V 2 piles AA de 1,5V

CAUTION

ATTENTION

650nm, P≤1mW, Class II laser product

Complies with 21 CFR parts

1040.10 and 1040.11

650nm, Puissance≤1mW, Produit laser de

classe II, Conforme au règlement 21 CFR

sections 1040.10 et 1040.11

LASER RADIATION

DO NOT STARE INTO BEAM

RAYONNEMENT LASER : NE REGARDEZ

PAS DIRECTEMENT LE FAISCEAU.

DATE CO DE: CODE DE DATE :

SELF-LEVELLING CROSS-LINE LASER LEVEL - 057-4587-6

Know your self-levelling cross-line laser level

3 5

No. Description No. Description

1 Mode button 5 1/4" threaded mounting hole

2 LED indicator 6 Battery compartment

3 Power switch 7 Stand

4 Laser aperture

The safe use of this product requires an understanding of the information on the tool and in this

Instruction manual, as well as knowledge of the project you are attempting. Before use of this

product, familiarize yourself with all operating features and safety rules.

Power switch

Push the power switch to the left position to

turn the self-levelling cross-line laser level

on, and slide the power switch to the right

position to turn the tool off (ﬁg 1).

To install batteries (ﬁg 2)

The battery compartment holds two “AA”

batteries.

1. Push the latch to open the battery cover.

2. Insert two new “AA” alkaline batteries,

following the polarity (+/-) as indicated on

the pole plate.

3. Securely close the cover.

NOTE:

• Always turn off the tool before installing

or replacing the batteries.

• Remove the batteries from the tool when

not using it for extended periods.

• The 2 AA batteries should match each

other in brand and type.

• Do not mix old and new batteries.

• Remove depleted batteries immediately, and dispose of them according to the laws and

regulations governing your community.

DESCRIPTION

OPERATING INSTRUCTIONS

g 2

Latch

g 1

OFF

SELF-LEVELLING CROSS-LINE LASER LEVEL - 057-4587-6

Laser line projection modes (ﬁg 3)

Your self-levelling cross-line laser level has

three laser-projection modes. To select a

speciﬁc laser-projection mode, press the

mode button until you reach the desired

projection mode. This laser tool defaults

to the cross-hair pattern mode when it is

turned on.

To choose a projection mode, press the

mode button:

1. Press the button once to select the

horizontal laser line.

2. Press the button twice to select the vertical laser line.

3. Press the button three times to return to the cross-hair pattern (horizontal and vertical).

Using your self-levelling cross-line laser level

Your self-levelling cross-line laser level has two working modes: Self-levelling mode and Lock

(manual) mode.

Self-levelling mode

In this mode, the tool will level itself if it is within ±4° of horizontal.

1. Place the self-levelling cross-line laser level on a ﬂat, smooth surface that is within ±4° of

horizontal.

2. Turn the tool on by sliding the power switch to the left position. The self-levelling cross-line

laser level will automatically level within 6 seconds. The LED indicator will shine green.

3. Press the mode button until the desired laser-projection mode is achieved and the laser line

is projected from the laser aperture.

4. If the surface on which the self-levelling

cross-line laser level is placed exceeds

±4° from horizontal, the laser line will

blink as an alarm and the LED indicator

will shine red. In this event, adjust the

angle of the surface slightly (ﬁg 4).

5. To turn off the laser lines, slide the switch

to the right position.

WARNING!

When turning the laser on, always be aware of protecting your eyes and the eyes of

those around you. Never point the laser light at anyone’s face, including your own.

Lock mode

This mode cannot be used to perform horizontal or vertical levelling, because the laser lines are

no longer self-balancing. In this mode, the LED indicator will always shine red.

1. Keep the power switch to the right position, press the mode button to turn on the laser. The

laser lines are now locked, and are no longer self-levelling.

2. Press the mode button repeatedly to change the laser-projection mode.

3. Slope your self-levelling cross-line laser level to project a straight line for reference. In this

mode, the laser lines are projected continuously and will not blink, even if the slope angle

exceeds 4°.

4. To turn the laser off, press the mode button repeatedly until the laser shuts off.

OPERATING INSTRUCTIONS

g 4

g 3

SELF-LEVELLING CROSS-LINE LASER LEVEL - 057-4587-6

Applications

Your self-levelling cross-line laser level can be hand-held for point marking and simple

alignment by sight, or it can be used to make a “chalk line” using the lock mode. It is ideal for

the following applications:

• Hanging pictures, photos, or artwork on walls

• Wallpapering and stencil work

• Framing doors and windows

• Installing electrical wiring and pipes

• Mounting wall ﬁxtures, electrical outlets, switches and lighting

• Installing a drop ceiling

• Painting

• Installing closets

• Laying tile and ﬂooring

Using with the stand

The highly versatile stand allows your self-levelling cross-line laser level to work in more

applications, such as mounted on a water pipe, banister, etc.

No. Description No. Description

1 Knob 1 4 1/4" screw platform

2 Knob 2 5 Rod

3 Handle

OPERATING INSTRUCTIONS

SELF-LEVELLING CROSS-LINE LASER LEVEL - 057-4587-6

To operate the stand

1. Securely clamp the stand to a pole, pipe

or other suitable item.

2. Loosen Knob 1 and adjust the 1/4"

screw platform to the desired

position. After adjustment tighten

Knob 1 (ﬁg 5 and ﬁg 6).

3. Mount the self-levelling cross-line laser

level to the 1/4" screw platform (ﬁg 7).

4. Loosen Knob 2 and adjust the orientation

of the rod such that the laser beam

projects to your target (ﬁg 8 and ﬁg 9).

5. Tighten Knob 2 again to lock the position.

57 mm

g 5

1/4"

g 7

360°

g 8

OPERATING INSTRUCTIONS

g 6

g 9

SELF-LEVELLING CROSS-LINE LASER LEVEL - 057-4587-6

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from

various types of commercial solvents and may be damaged by their use. Use clean cloths to

remove dirt, dust, oil, grease, etc.

Do not, at any time, allow brake ﬂuids, gasoline, petroleum-based products, penetrating oils,

etc. to come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic

which may result in serious personal injury.

When servicing, use only identical replacement parts. Use of any other parts may create

a hazard or cause product damage. To ensure safety and reliability, all repairs should be

performed by a qualiﬁed service technician.

Remove the batteries when cleaning the laser tool.

Storing the self-levelling cross-line laser level

The following steps should be taken in order to prepare the self-levelling cross-line laser level

for storage.

• Remove the batteries from the tool and store it in a cool dry location.

• Always store the tool indoors. When not in use, always store the tool in its protective case.

• After you have ﬁnished using the tool, always make sure that the switch is in the off position.

PROBLEM POSSIBLE CAUSES SOLUTIONS

The laser line

projection is weak

Batteries are weak Replace with new batteries

The laser line is

hard to see

The tool is too far from the target

Move the tool closer to

the target

Laser line is not

projected

No batteries installed or batteries are

depleted

Install new batteries

Laser line ﬂickers

for alert

The surface where the tool has been

placed is uneven or the tool is out of

its automatic self-levelling range

1. Place the tool on a more

level surface

2. Set the tool to its lock

mode

If the problem remains unsolved after performing the checks described above, call

the toll-free helpline, at 1-800-689-9928.

MAINTENANCE

TROUBLESHOOTING

SELF-LEVELLING CROSS-LINE LASER LEVEL - 057-4587-6

Exploded view

No. Part No. Description No. Part No. Description

1 3126974000 Slide Button 24 5610013000 Tapping Screw

2 3126976000 Left Housing 25 5610005000 Tapping Screw

3 4870343000 Micro Switch 26 3704889000 Magnetic Holder

4 5610004000 Tapping Screw 27 4890718000 PCB Assembly

5 3126972000 Handspike 28 3126971000 Support

6 5650033000 Plain Washer 29 3660316000 Spring

7 4580001000 PCB Board 30 3680138000 Magnet Ring

8 5620100000 Hexagon Socket Screw 31 5670153000 Pin

9 5700002000 Ball Bearing 32 2820009000 Contactor

10 3123982000 Rubber Gasket 33 5620202000 Screw

11 3420741000 Top Support 34 3700042000 Sheet copper

12 4890969000 PCB Assembly 35 2780015000 Laser Module

13 5620058000 Screw 36 3421447000 Main Support

14 3126977000 Top Cover 37 3552004000 Pendulum

15 3705466000 Control Panel 38 3704986000 Paster

16 3124822000 Rubber Protector 39 3550488000 Guiding Roller

17 3520368000 Shaft 40 5670017000 Parallel Pin

18 5620394000 Screw With Washer 41 3321123000 Brake Assembly

19 3660304000 Spring 42 5630228000 Collar Nut

20 3660305000 Spring 43 3126978000 Decorate Cover

21 3126980000

Contact Receptacle Assembly

44 3690137000 Transparent Guard

22 3126975000 Battery Cover 45 3126979000 Rubber Protector

23 3126973000 Right Housing

If any parts are missing or damaged, or if you have any questions,

please call the Toll-free Helpline, at 1-800-689-9928.

PARTS LIST

SELF-LEVELLING CROSS-LINE LASER LEVEL - 057-4587-6

Exploded view of the stand

No. Part No. Description No. Part No. Description

1 057458701 Short screw arbor knob 7 057458707 Screw swinging arm

2 057458702 The clip body 1 8 057458708 Swing arm

3 057458703 Torsional spring 9 057458709 Long screw arbor knob

4 057458704 The clip body 2 10 057458710 The universal ball assembly

5 057458705 Axle sleeve 11 057458711 End sheet

6 057458706 The knob shaft

If any parts are missing or damaged, or if you have any questions,

please call the Toll-free Helpline, at 1-800-689-9928.

This Mastercraft product is guaranteed for a period of 3 years from the date of original retail

purchase against defects in workmanship and materials, except for the following components:

Accessories, which are guaranteed for a period of 1 year from the date of original retail

purchase against defects in workmanship and materials. Subject to the conditions and

limitations described below, this product, if returned to us with proof of purchase within the

stated warranty period, and if covered under this warranty, will be repaired or replaced (with

the same model, or one of equal value or speciﬁcation), at our option. We will bear the cost of

any repair or replacement and any costs of labour relating thereto.

These warranties are subject to the following conditions and limitations:

a) a bill of sale verifying the purchase and purchase date must be provided;

b) this warranty will not apply to any product or part thereof that is worn or broken or that has

become inoperative due to abuse, misuse, accidental damage, neglect or lack of proper

installation, operation or maintenance (as outlined in the applicable owner’s manual or

operating instructions) or that is being used for industrial, professional, commercial or rental

purposes;

c) this warranty will not apply to normal wear and tear or to expendable parts or accessories

that may be supplied with the product that are expected to become inoperative or unusable

after a seasonable period of use;

d) this warranty will not apply to routine maintenance and consumable items, including but not

limited to fuel, lubricants, vacuum bags, blades, belts, sandpaper, bits, ﬂuids, tune-ups or

adjustments;

e) this warranty will not apply where damage is caused by repairs made or attempted by others

(i.e.: persons not authorized by the manufacturer);

f) this warranty will not apply to any product that was sold to the original purchaser as a

reconditioned or refurbished product (unless otherwise speciﬁed in writing);

WARRANTY

PARTS LIST

SELF-LEVELLING CROSS-LINE LASER LEVEL - 057-4587-6

g) this warranty will not apply to any product or part thereof if any part from another

manufacturer is installed therein or any repairs or alterations have been made or attempted

by unauthorized persons;

h) this warranty will not apply to normal deterioration of the exterior ﬁnish, including but not

limited to scratches, dents, paint chips, or to any corrosion or discolouring by heat, abrasive

and chemical cleaners; and

i) this warranty will not apply to component parts sold by and identiﬁed as the product of

another company, which shall be covered under the product manufacturer’s warranty, if any.

Additional Limitations

This warranty applies only to the original purchaser and may not be transferred. Neither the

retailer nor the manufacturer shall be liable for any other expense, loss or damage, including

but not limited to any indirect, incidental, consequential or exemplary damages arising in

connection with the sale, use or inability to use this product.

Notice to Consumer

This warranty gives you speciﬁc legal rights, and you may have other rights, which may vary

from province to province. The provisions contained in this warranty are not intended to limit,

modify, take away from, disclaim or exclude any statutory warranties set forth in any applicable

provincial or federal legislation.

IMPORTED BY MASTERCRAFT CANADA TORONTO, CANADA M4S 2B8

WARRANTY

MasterCraft 057-4587-6 User manual

Brand: MasterCraft

Model: 057-4587-6

Category: Laser levels

Type: User manual

Download PDF

report

MasterCraft 057-4587-6 User manual

MasterCraft 057-4587-6 User manual

Related papers

Other documents