Ryobi RLL10RD is a cross line laser that helps you determine and verify horizontal and vertical lines with ±0.5 mm/m accuracy, up to a 10 m working range. Utilizing a self-leveling mechanism with a range of ±3°, it ensures precise alignment within 2 to 5 seconds. The clear and visible laser lines, projected at a fan angle greater than 100°, make leveling and alignment tasks easier.
Ryobi RLL10RD is a cross line laser that helps you determine and verify horizontal and vertical lines with ±0.5 mm/m accuracy, up to a 10 m working range. Utilizing a self-leveling mechanism with a range of ±3°, it ensures precise alignment within 2 to 5 seconds. The clear and visible laser lines, projected at a fan angle greater than 100°, make leveling and alignment tasks easier.
RLL10RD
RLL15GN
FRONT PAGE
2Original Instructions
IMPORTANT!
It is essential that you read the
instructions in this manual before
assembling, operating, and maintaining
the product.
Subject to technical modications.
INTENDED USE
The cross line laser is intended to be
used only by adults who have read and
understood the instructions and warnings
in this manual, and can be considered
responsible for their actions.
The product is intended for determining
and verifying horizontal and vertical lines.
Do not use the product for any other
purpose. Use of the product for operations
different from intended could result in a
hazardous situation.
CROSS LINE LASER SAFETY
WARNINGS
■Laser radiation. Do not stare into
beam. Class 2 laser product.
■Risk of severe eye injury if the laser
beam is directed at persons or
animals. Avoid direct eye exposure.
■Do not direct the laser beam towards
other people.
■Do not operate the product around
children or allow children to operate
the laser.
■Avoid using the product on reflective
surfaces. The laser beam may be
reflected at the operator or other
persons.
■Store the product indoors and avoid
substantial knocks, continuous
vibration or extreme temperatures.
■Always keep the product away from
dust, liquids and high humidity. They
may damage internal components or
affect accuracy.
■If laser beam hits your eye, you must
close your eyes and immediately turn
your head away from the beam.
■Do not position the laser beam so that
it unintentionally blinds you or others.
■Do not look into a laser beam using
magnifying optical devices such as
binoculars or a telescope. This will
increase the level of eye injury.
■If you use laser goggles to enhance
the visibility of the laser beam, note
that they will not protect your eyes
against laser radiation.
■Do not remove or deface warning
labels on the product.
■Do not disassemble the product.
■Avoid heavy impact to or dropping of
the laser. The accuracy of the laser
should be checked before use if it has
been dropped or subjected to other
mechanical stresses.
■Do not operate the product in
explosive areas or in extreme
environments.
SELF-LEVELLING LED INDICATOR
LED indicator Explanation
Green Self-leveling is complete.
Red
Self-leveling is not
successful; laser line blinks.
Place the product in a
horizontal position of +/-3°.
MAINTENANCE
■Avoid using solvents when cleaning
plastic parts. Most plastics are
susceptible to various types of
commercial solvents and may be
3
Original Instructions
damaged by their use. Use clean
cloths to remove dirt, carbon dust,
etc.
■For greater safety and reliability, all
repairs should be performed by an
authorised service centre.
SYMBOLS ON THE PRODUCT
V Volts
Direct current
Regulatory Compliance
Mark (RCM).
Product meets
applicable regulatory
requirements.
Please read the
instructions carefully
before starting the
machine.
Class 2 laser beam.
Do not stare into the
laser beam.
Do not dispose of waste
batteries, waste electrical
and electronic equipment as
unsorted municipal waste.
Waste batteries and waste
electrical and electronic
equipment must be coll ected
separately. Waste batteries,
waste accumulators, and light
sources have to be removed
from the equipment. Check
with your local authority or
retailer for recycling advice
and collection point. According
to local regulations, retailers
may have an obligation to
take back waste batteries and
waste electrical and electronic
equipment free of charge. Your
contribution to the reuse and
recycling of waste batteries and
waste electrical and electronic
equipment helps to reduce
the demand of raw materials.
Waste batteries, in particular
containing lithium, and waste
electrical and electronic
equipment contain valuable
and recyclable materials, which
can adversely impact the
environment and the human
health if not disposed of in an
environmentally compatible
manner. Delete personal data
from waste equipment, if any.
SYMBOLS IN THIS MANUAL
Note
Do not stare into the
laser beam.
4Know your product
Clamp
Operator’s manual
1/4” tripod mount
Battery
On/off switch
Battery door
Exit window for laser beam
Self-levelling LED indicator
5
Getting started
1
3
2
3
6Operation
2
1
2
3
2
2
3
PRODUCT SPECIFICATIONS
Cross Line Laser
Model RLL10RD RLL15GN
Accuracy ±0.5 mm/m ±0.5 mm/m
Laser wavelength 635nm ± 5nm 520nm ± 10nm
Fan angle >100° >100°
Colour Red Green
Working range 10 m 15 m
Laser class 2, <1mW 2, <1mW
Projection Cross Line Cross Line
Self-Leveling Time 2s ~ 5s 2s ~ 5s
Self-Leveling Angle ± 3° ± 3°
Operating Time 24 h 6 h
Battery technology 2 x AA LR6 Alkaline 2 x AA LR6 Alkaline
Supply voltage 2 x 1.5V 2 x 1.5V
Operating temperature range 0°C ~ 40°C 0°C ~ 40°C
Storage temperature range -20°C ~ 70°C -20°C ~ 70°C
Dimensions L69 x W63 x H72 mm L69 x W63 x H72 mm
BACK PAGE
Imported by:
Techtronic Industries Australia Pty Ltd
31 Gilby Road, Mount Waverley, VIC 3149
Melbourne, Australia
Techtronic Industries N.Z. Limited
Unit C, 70 Business Parade South,
Highbrook, Auckland 2013, New Zealand
RYOBI is a trade mark of Ryobi Limited, and is used under license.
20230303v1
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ryobi RLL10RD is a cross line laser that helps you determine and verify horizontal and vertical lines with ±0.5 mm/m accuracy, up to a 10 m working range. Utilizing a self-leveling mechanism with a range of ±3°, it ensures precise alignment within 2 to 5 seconds. The clear and visible laser lines, projected at a fan angle greater than 100°, make leveling and alignment tasks easier.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Bosch Power Tools GPL5 User manual
-
Skil 8201-CL User manual
-
Bosch Appliances GLL2-50 User manual
-
BAUKER NLCO1 Owner's manual
-
Draper Self-Levelling Laser Level Kit Operating instructions
-
Hammerhead HLCL001 Owner's manual
-
Powerplus POWX720 Owner's manual
-
MasterCraft 057-4587-6 User manual
-
-
Bosch GLL 2-20 User guide
