Humandata EDA-013-80 User manual

Brand
Humandata
Model
EDA-013-80
Type
User manual

This manual is also suitable for

HuMANDATA LTD.
USB 3.0 with Cyclone 10 LP
USB-FPGA Board
EDA-013 Series
User’s Manual
Ver. 1.1
Table of Contents
Revision History .............................................................................................. 1
Introduction .................................................................................................... 1
Unused Pins [IMPORTANT] ........................................................................... 1
1. Specifications ..................................................................................................... 2
2. Overview ............................................................................................................ 3
2.1. Name of Parts .......................................................................................................3
2.2. Block Diagram ......................................................................................................4
2.3. Power Supply ........................................................................................................4
2.4. Clock ......................................................................................................................4
2.5. I/O ..........................................................................................................................5
2.6. Setting Switch ......................................................................................................6
2.7. USB Controller (FT601) ......................................................................................6
2.8. USB Controller (FT232H) ...................................................................................7
3. FPGA Configuration ........................................................................................... 8
3.1. Using Original Tool ..............................................................................................8
3.2. Using JTAG Download cable ...............................................................................9
3.3. Using Configuration Device ................................................................................9
4. Device Driver ................................................................................................... 10
5. Factory Setting of FT232H EEPROM ............................................................... 11
6. Documentation and User Support .................................................................... 12
Precautions
Do Not
1. This product uses ordinary off-the-shelf electronic components, and is therefore inappropriate for use in
applications that require special quality or reliability and are expected to protect human lives or prevent
accidents, such as safety mechanisms in fields including space, aeronautics, medicine, and nuclear
power.
2. Do not be used underwater or in high-humidity environments.
3. Do not be used in the presence of corrosive gases, combustible gases, or other flammable gases.
4. Do not turn on power when circuit board surface is in contact with other metal.
5. Do not apply voltage higher than rated voltage.
Attention
6. This manual may be revised in the future without notice owing to improvements.
7. All efforts have been made to produce the best manual possible, but if users notice an error or other
problem, we ask that they notify us.
8. Item 7 notwithstanding, HuMANDATA cannot be held liable for the consequences arising from use of
this product.
9. HuMANDATA cannot be held liable for consequences arising from using this product in a way different
from the uses described herein, or from uses not shown herein.
10. This manual, circuit diagrams, sample circuits, and other content may not be copied, reproduced, or
distributed without permission.
11. If the product emits smoke, catches fire, or becomes unusually hot, cut the power immediately.
12. Be careful of static electricity.
13. This product may be subject to the export restrictions of Japan, the United States, or other countries.
Purchasers are responsible for properly observing export restrictions.
14. HuMANDATA firmly refuses to export (including reexporting) products to countries or regions subject to
export restrictions.
Product Warranty and Scope of Support
1. HuMANDATA guarantees that its products can be assembled as shown in published circuit diagrams and other design documents.
There may be differences between actual components or their prescribed quantities and model numbers and those shown in circuit
diagrams.
2. Except for the guarantee in item 1, above, no guarantees whatsoever are made. When assembling the product as shown in a circuit
diagram is impossible, and the problem can be solved by revising the diagram, HuMANDATA will revise the diagram. When a problem
can be solved only by replacing components or modifying the product, HuMANDATA will take back the product to replace it with a
properly functioning product.
3. In case item 2, above, HuMANDATA guarantee its products for a period of 60 days from the date of shipping.
4. If the problem is minor, HuMANDATA will sometimes describe how to make the revision or modification, and ask the customer to
solve the problem.
5. HuMANDATA will determine how to honor the warranty, as through repair, replacement, return, or other action. The customer cannot
specify what action to take.
6. FPGAs and other components used in products sometimes have characteristic defects. Returns and replacements are not possible
even if such defects are discovered, whether before or after purchase.
7. HuMANDATA shall not be obligated to inform customers about defects in the main components used in products.
8. HuMANDATA shall not be obligated to provide support for products, or to provide support for the software of other companies needed
to use HuMANDATA products.
9. Published documentation shall be limited to that published by HuMANDATA at the time of product purchase, and HuMANDATA shall
not be obligated to provide any other documentation.
10. When repairs or replacements are provided under warranty in Japan, purchaser shall pay shipping charges for shipping to
HuMANDATA, and HuMANDATA shall pay shipping charges for shipping to purchaser.
11. When shipping from outside of Japan, purchaser shall pay all expenses including shipping charges and taxes.
12. Under whatever circumstances, HuMANDATA shall provide support for its products for a maximum of one year after shipping from
factory.
13. The Warranty is not applicable and support ends in the event of fire, storm and flood damage, earthquakes, lightning strikes, and
other natural disasters, as well as conflict or other occurrences.
14. Purchaser is assumed to have read and understood all the above when purchasing a HuMANDATA product.
Limitation of Liability
1. Purchasers assume all liability associated with the use of this product.
2. HuMANDATA assumes no liability whatsoever for any direct, indirect, special, incidental, or consequential damages arising from the
use of this product, even if HuMANDATA has been advised of the possibility of such damage, whether legal or in tort.
3. At the time this product is purchased, items 1 and 2 above shall be deemed to have been confirmed by purchaser.
Trademarks and Other Considerations
1. This manual uses various companies’ trademarks in places.
2. HuMANDATA is this company’s registered trademark.
HuMANDATA’s Philosophy
1. HuMANDATA endeavors to raise product quality. We continually make detailed improvements and adjustments that are not shown
in circuit diagrams.
2. HuMANDATA actively publishes, on the Web and in other ways, information considered useful to customers. Examples would be
how to use FPGAs and how to use development tools.
3. HuMANDATA makes efforts for the long-term provision of products and for continuing their long-term support.
4. Instead of concealing small product problems and documentation errors, HuMANDATA makes them public.
5. HuMANDATA abides by Japanese law and its spirit. We make no transactions with purchasers who commit illegal acts.
1
EDA-013 v1.0
Revision History
Date
Revision
Description
Feb. 16, 2021 v1.0 Initial release
Mar. 28, 2022 v1.1
Add description of Dual-Purpose Pins in Chapter 2.8
Add description of rbf file setting in Chapter 3.1
Introduction
Thank you for purchasing our product EDA-013.
EDA-013 is a USB-FPGA board with USB interface equipped with Intel FPGA
Cyclone 10 LP series and FTDI's USB controller FT601.
By using the original configuration tool “BBC[EDA-013]”, no download cable or
Intel developing environment is needed to configure FPGA and configuration
device on the board.
Unused Pins [IMPORTANT]
For supporting device migration, some I/O pins of this board are configured to
power supply pins. These pins are needed to be set as a dummy input depending
on the device grades, and please do not use them.
To set all unused pins as input pins, please refer to the steps below:
1. Open “Assignments” and click “Device”
2. Click “Device and Pin Options…” button
3. Open “Unused Pins” category
4. Set “Reserve all unused pins” as “As input tri-stated”
2
EDA-013 v1.0
1. Specifications
Model Name
EDA-013-80 EDA-013-120
FPGA
10CL080YF780C8G
10CL120YF780C8G
USB 3.0 Controller
FT601 (FTDI)
USB 2.0 Controller
Config. Device
MT25QL128ABA1ESE-0SIT (Micron, 128Mbit)
SDRAM
SPI-FLASH
MT25QL128ABA1ESE-0SIT (Micron, 128Mbit)
Power Input
(Internal power is generated by on-board regulator)
User I/O
100 (CNA: 50, CNB: 50)
On-Board Clock
User LED
2
User Switch
Status LED
Power (red) x1, Done (blue) x1
Power-On Reset
User I/Os
66-pin through-hole
dia. 0.9 (typ.) [mm], 100[mil]/2.54 [mm] pitch
JTAG Connector
PCB
8 Layer FR-4 t1.6 [mm] Immersion gold
Dimensions
Weight
33 [g] typ.
Accessories
DIL80 pin header x 2
RoHS Compliance
YES
* There may be cases that these parts and specifications are changed.
3
EDA-013 v1.0
2. Overview
2.1. Name of Parts
Component Side
Solder Side
VIO(B)
Setting Jumper
User I/Os
(CNB)
DONE LED
FT601
Setting Jumper
FT232H
USB
Connector
FPGA
JTAG
Oscillator
User I/Os
(CNA)
FT601
User LEDs
User SW
3.3V Output
Setting Jumper
VIO(B)
Setting Jumper
4
EDA-013 v1.0
2.2. Block Diagram
2.3. Power Supply
This board operates from single DC 5.0 V power supply from user I/O pins number
3 and 4 of CNA and CNB connector. The external power supply should be
sufficient and stabilized. USB bus power is not supported.
2.4. Clock
A 50 MHz oscillator (U4) is equipped as an on-board clock.
Some user I/O pins can be used for clock input pins.
For more details, please refer to the circuit schematics.
Cyclone 10 LP
10CL080YF780C8G
10CL120YF780C8G
JTAG
Config. Device
JTAG
Buffer
Config.
User
User I/Os CNB
User I/Os CNA
VIO(B) INPUT
5.0 V INPUT
Power LED (3.3V)
Power Circuit
3.3V, 2.5V, 1.1V
User Switch
2
User LED
Config. Switch
Done LED
USB
3.0
3.3V Output (Option)
5.0 V INPUT
Oscillator
50
MHz
50
EDA-013 Rev.A
.jic
High Speed
USB Bridge
FT232H
Super Speed
USB Bridge
FT601
50
User
2
SPI Flash
SDRAM
5
EDA-013 v1.0
2.5. I/O
FPGA banks are divided into two groups as follows. IOA*, I/Os of CNA, are belongs
to BANK Group A. Power supply for I/Os is fixed to on-board 3.3V.
IOB*, I/Os of CNB, are belongs to BANK Group B. Power supply for I/Os, VIO(B),
is connected to on-board 3.3V, but external input also be available.
FPGA BANK Vccio BANK Group
B1
V33A
A
B2
V33A
A
B3
V33A
A
B4
V33A
A
B7
V33A
A
B8
V33A
A
B5
VIO(B)
B
B6
VIO(B)
B
When you use external VIO(B) from CNB pins 1 and 2,
please short JP1 pins 2 and 3, and remove JR2.
Component Side
Solder Side
You can output on-board 3.3V from CNA pins 1 and 2.
When you use this function, please short JR1.
Factory Setting
3.3 V Output Setting
3 2 1
1 2 3
6
EDA-013 v1.0
2.6. Setting Switch
You can use SW2 to set a configuration mode of the FPGA.
SW2
Configuration Mode
1
2
MSEL
User
PS
ON
X
AS
OFF
X
ON: Low, X: Don’t Care
PS mode: Configured by JTAG or original configuration tool
AS mode: Configured by configuration device.
2.7. USB Controller (FT601)
The FT601 is mounted on this board as a USB controller IC. FT601 is connected to
FPGA with 32 bit bus.
Before FPGA is configured, FT232H is recognized by PC with priority. After
configuration, it is up to user. Please refer to the following table about control
signals.
Net Label FPGA Pin Function
XFT601RESET B3
Reset FT601
- FPGA High/Hi-Z : FT601 is reset
- FPGA Low : FT601 is active
XUSB2SEL B4
Change USB 2.0 signal connection
- FPGA High/Hi-Z : Connect to FT232H
- FPGA Low : Connect to FT601
When you need to make FT601 to be recognized by PC without FPGA
configuration, please short both of two pins of JP2. Normally, please set them to be
opened.
Open (Factory Setting)
Short
7
EDA-013 v1.0
2.8. USB Controller (FT232H)
The FT232H is mounted on this board for FPGA configuration. You can also use it
as a user communication IC. FT232H cannot be simultaneously used with FT601.
Before FPGA is configured, FT232H is recognized by PC with priority. After
configuration, it is up to user. Please refer to the following table about control
signals.
Net Label FPGA Pin Function
XFT232RESET F21
Reset FT232H
- FPGA High/Hi-Z : FT232H is active
- FPGA Low : FT232H is reset
XUSB2SEL B4
Change USB 2.0 signal connection
- FPGA High/Hi-Z : Connect to FT232H
- FPGA Low : Connect to FT601
ADBUS0/ADBUS1 of FT232H and B22/A23 of FPGA are connected to P3/N7 via
resistors. In the case of using FT232H as user communication IC, please refer to
setting of Dual-Purpose Pins. For more details, please refer to the circuit
schematics and datasheet of FPGA.
8
EDA-013 v1.0
3. FPGA Configuration
3.1. Using Original Tool
By using the original configuration tool “BBC[EDA-013]”, following function is
available without download cable.
● FPGA configuration
● Write and Erase configuration device
BBC[EDA-013] is available for free from a support page. Please set configuration
mode to PS when using this tool.
The tool supports rbf file. The file can be generated by the setting in “Device
and Pin Options – Programming Files”.
9
EDA-013 v1.0
To write the data into the configuration device, please set up the following items in
“Device and Pin Options – Configuration”.
Configuration scheme: Active Serial
Configuration device: MT25QL128
3.2. Using JTAG Download cable
Download cable is needed to use Intel tool (SignalTap II etc.). Pin assignment is as
follows.
CN2
3.3. Using Configuration Device
Configuration data written in the configuration device will be configured to the
FPGA automatically when power is applied. To use this function, set configuration
mode to “Active Serial” mode.
Do not download inaccurate configuration data. It would damage the FPGA and
peripheral circuit.
Signal
Name
JTAG Pin
Signal
Name
TCK 1 2 GND
TDO 3 4 VCC
TMS
5
6
-
-
7
8
-
TDI 9 10 GND
10
EDA-013 v1.0
4. Device Driver
To recognize USB controller, installing device driver is needed. The first time
EDA-013 is connected to a PC, installing it is required by Operation System.
The device driver and installation instruction are available from a support page.
FT601: displays as a "FTDI FT601 USB 3.0 Bridge Device” in universal serial bus
controller
FT232H: displays as an "EDA-013 VCP” in universal serial bus controller, and as a
"EDA-013 (COM *)” in Port (COM and LPT)
Device driver for FT601 is available from the following FTDI web page.
https://www.ftdichip.com/Drivers/D3XX.htm
11
EDA-013 v1.0
5. Factory Setting of FT232H EEPROM
Factory presetting is as follows. The other items are not changed from the default.
12
EDA-013 v1.0
6. Documentation and User Support
The following documents and other supports are available at
https://www.hdl.co.jp/en/spc/EDA/eda-013/
Circuit Schematic
Pin List
Outline Drawing
Net List
Original Configuration Tool “BBC[EDA-013]”
Device Driver
Device Driver Installation Instruction
… and more.
USB 3.0 with Cyclone 10 LP USB-FPGA board
EDA-013 Series
User’s Manual
Ver. 1.1 ........................................ March 25, 2022
HuMANDATA LTD.
Address: 1-2-10-2 F, Nakahozumi, Ibaraki
Osaka, Japan
ZIP 567-0034
Tel: 81-72-620-2002 (Japanese)
Fax: 81-72-620-2003 (Japanese/English)
URL: https://www2.hdl.co.jp/en/ (Global)
https://www.hdl.co.jp/ (Japan)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Humandata EDA-013-80 User manual

Brand
Humandata
Model
EDA-013-80
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents