QEP 22900Q User manual

READ AND FOLLOW ALL SAFETY AND

OPERATING INSTRUCTIONS BEFORE USING THIS SAW.

LIRE ET SUIVRE TOUTES LES DIRECTIVES

DE SÉCURITÉ ET D’OPÉRATION AVANT D’UTILISER CETTE SCIE.

LEA Y SIGA TODAS LAS INSTRUCCIONES

DE FUNCIONAMIENTO Y SEGURIDAD ANTES DE USAR ESTA SIERRA.

POWER PRO

1 HP TILE SAW

OWNER’S MANUAL

SCIE COUPE-CARREAUX

DE 1 HP

MANUEL D'UTILISATION

SIERRA ELÉCTRICA DE

1HP PARA CORTAR LOSETAS

MANUAL DE OPERACIÓN

22900Q

7 in.

180 mm

WET TILE SAW

29FG

E234797

English ..................................................................page 1

FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL

BEFORE OPERATING SAW.

1. Always wear safety goggles when cutting.

2. Use blade guard for every operation for which it can be used.

3. Disconnect saw before cleaning or changing blade.

4. Do not use any cutting blade with openings and grooves. Use only continuous rim blades.

5. Replace damaged blade before operating.

6. Do not expose to rain or use in damp locations.

LIMITED WARRANTY — Refer to warranty card.

Français ................................................................page 12

POUR ASSURER VOTRE SECURITE,

LISEZ LE MOIDE D'EMPLOI AVANT D'UTILISER LE COUPEUR.

1. Toujours porter des lunettes protectrices pendant la coupe.

2. Utiliser le pare-éclaboussure pour chaque opération dont il peutêtre utiliser.

3. Débrancher l'outil avant de la nettoyer ou de changer les roues.

4. Ne pas utiliser des roues à couper avec des trous ou creux. Utiliser seulement des roues à

couper lisses.

5. Remplacer les roues à couper endommagés avant de faire fonctionner l'outil.

6. Ne pas exposer à la pluie ou utiliser dans des endroits humides.

GARANTIE LIMITÉE — Faire référence à la carte de guarantie.

Español................................................................página 23

LEE ESTA INSTUCCION MANUAL ANTES

DE USA LA SIERRA PARA TU BIEN.

1. Siempre utilice gafas de protección al cortar.

2. Utilice una capota de protección para cada operación en la cual la puede utilizar.

3. Desconectar la sierra antes de limpiarla o antes de cambiar el disco de corte.

4. No utilice ningún disco de corte que tenga aperturas o ranuras. Solamente utilice discos de

corte lisos.

5. Reemplace el disco de corte cuando esté dañado.

6. No la exponga a la lluvia o no la utilice en áreas húmedas.

GARANTIA LIMITADA — Referirse a la tarjeta de guarantia.

Servicio al cliente de Q.E.P.: 1-866-435-8665

Q.E.P. Customer Service: 1-866-435-8665

Support de la clientèle de Q.E.P.: 1-866-435-8665

– 1 –

TABLE OF CONTENTS

General safety instructions................1

Warning ................................2

Electrical requirements . . . . . . . . . . . . . . . . . . . 3

Extension cords.......................... 3

California Proposition 65 ..................4

Description.............................. 4

Assembly ..............................5-7

Operation ..............................7-8

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Troubleshooting..........................9

Parts list ...............................10

Exploded parts diagram..................11

GENERAL SAFETY

INSTRUCTIONS

READ THIS OWNER'S

MANUAL COMPLETELY AND MAKE

SURE YOU UNDERSTAND ALL OF IT'S

SAFETY GUIDELINES.

1. KEEP GUARDS IN PLACE and in

working order.

2. REMOVE ADJUSTING KEYS AND

WRENCHES. Before turning on the tile saw,

make sure the keys and adjusting wrenches

have been removed.

3. KEEP WORK AREA CLEAN. Cluttered areas

and benches invite accidents.

4. ALWAYS REMAIN ALERT WHEN THE SAW

IS IN USE. Inattention on the part of the

operator may lead to serious injury.

5. DON’T USE IN A DANGEROUS

ENVIRONMENT. Don’t use power tools in

damp or wet locations or expose them to

rain. Keep work area well lit.

6. KEEP CHILDREN AWAY. Anyone in the

cutting vicinity should remain at a safe

distance from work area.

7. MAKE WORKSHOP CHILD-PROOF with

padlocks, master switches or by removing

starter keys.

8. USE THE RIGHT TOOL. Don’t use a tool or

attachment to do a job for which it was

not designed.

9. USE THE PROPER EXTENSION CORD.

Make sure your extension cord is in good

condition. When using an extension cord,

be sure to use one heavy enough to carry

the current your product will draw. An

undersized cord will cause a drop in line

voltage resulting in loss of power and

overheating. TABLE 1 (page 4) shows the

correct size to use depending on cord

length and nameplate ampere rating. If

in doubt, use the next heavier gauge. The

smaller the gauge number, the heavier

the cord.

10. DON’T FORCE THE TOOL. It has been

designed to operate at maximum safety and

performance levels.

11. DO NOT FORCE THE MATERIAL BEING CUT.

Always let the blade cut at its own speed.

12. WEAR PROPER APPAREL. Do not wear

loose clothing, neckties, rings, bracelets

or other jewelry which may get caught

in moving parts. Non-slip foot wear is

recommended. Wear protective hair

covering if you have long hair.

13. ALWAYS USE SAFETY GLASSES. Also use

face or dust mask for commercial cutting

operations. Everyday eyeglasses only have

impact-resistant lenses, they are NOT

safety glasses.

14. DON’T OVERREACH. Keep proper footing

and balance at all times.

15. MAINTAIN TOOLS WITH CARE. Keep tools

clean and in good working condition for

maximum safety performance.

16. DISCONNECT SAW BEFORE SERVICING

– when changing accessories, such as

blades, bits, cutters, etc.

POWER PRO

1 HP TILE SAW

OWNER’S MANUAL

– 2 –

17. REDUCE THE RISK OF UNINTENTIONAL

STARTING. Make sure switch is in OFF

position before plugging in.

18. USE RECOMMENDED ACCESSORIES.

Consult the owner’s manual for

recommended accessories. The use of

improper accessories may increase risk of

injury.

19. DO NOT DRY CUT WITH BLADES

DESIGNED FOR WET CUTS.

20. Make sure you USE THE CORRECT BLADE

for the type of material that is being cut.

21. NEVER STAND ON TOOL. Serious injury

could occur if the wet saw is tipped or if the

cutting tool is unintentionally contacted.

22. CHECK DAMAGED PARTS. Before further

use of the tool, damaged part(s), (i.e.,

guard) should be carefully checked to

determine that it will operate properly

and perform its intended function. Check

for alignment of moving parts, binding of

moving parts, breakage of parts, mounting

and any other condition that may affect the

saw’s operation. A guard or other part that

is damaged should be properly repaired

or replaced.

23. Ensure that BLADE IS TRAVELING

THROUGH WATER RESERVOIR FOR WET

CUTTING.

24. CHECK DIAMOND BLADES carefully for

cracks, nicks, missing diamond matrix

or out-of-alignment condition. Replace

damaged blades immediately. DO NOT

USE DAMAGED BLADES. They may cause

bodily injury.

25. DIRECTION OF FEED. Feed work into the

blade against the direction of rotation of

the blade only.

26. DO NOT ALTER THE PLUG or use a 2-prong

receptacle. This saw is equipped with a

3-prong electrical plug.

27. NEVER LEAVE SAW RUNNING

UNATTENDED. Turn power off. Don’t leave

tool until it comes to a complete stop.

28. POSITIONING OF TILE SAW (see FIGURE 1)

FIGURE 1

• To avoid the possibility of the appliance plug

or receptacle getting wet, position the tile

saw to one side of a wall-mounted receptacle

to prevent water from dripping onto the

receptacle or plug. The user should arrange

a “drip loop” in the cord connecting the saw

to a receptacle. The “drip loop” is that part

of the cord below the level of the receptacle,

or connector if an extension cord is used, to

prevent water traveling along the cord and

coming in contact with the receptacle.

• If the plug or receptacle does get wet, DO

NOT unplug the cord. Disconnect the fuse

or circuit breaker that supplies power to the

tool. Then, unplug and examine for presence

of water in the receptacle.

WARNING

PERSONAL INJURY CAN OCCUR IF OPERATED

IMPROPERLY.

• Keep ﬁngers and loose clothing away from

rotating blade.

• Use extreme caution when cutting tile. Make

sure hands and ﬁngers are clear from the

blade groove in the table. Severe abrasion,

cuts, or pinching of hands or ﬁngers can occur.

• Electrical shock can occur if operating

instructions are not followed.

FOR YOUR OWN SAFETY READ INSTRUCTION

MANUAL BEFORE OPERATING SAW.

• Wear eye protection.

• Use blade guard for every operation for

which it can be used.

• Unplug saw before servicing, when changing

cutting wheels, and cleaning.

– 3 –

• Use tool only with smooth-edge cutting

wheels free of openings and grooves.

• Replace damaged cutting wheel

before operating.

• Do not ﬁll water tray above raised over ﬂow

drain.

ELECTRICAL

REQUIREMENTS

1. THIS TILE SAW MUST BE CONNECTED TO

A GROUNDED POWER SOURCE while in

use to protect the operator from electrical

shock.

2. IN THE EVENT OF A MALFUNCTION OR

BREAKDOWN, grounding provides a path

of least resistance for electrical current

to reduce the risk of electrical shock. This

tile saw is equipped with an electrical

cord with a grounding conductor and

a grounding plug. Insert the 3-prong

electrical plug into a 3-pole receptacle

that is properly installed and grounded

in accordance with all local codes and

ordinances.

3. DO NOT MODIFY THE PLUG provided if it

will not ﬁt the outlet. Have the proper outlet

installed by a qualiﬁed electrician.

4. IMPROPER CONNECTION OF THE

EQUIPMENT-GROUNDING CONDUCTOR

CAN RESULT IN A RISK OF ELECTRIC

SHOCK. The conductor with insulation that

is green on the outside (with or without

yellow stripes) is the equipment-grounding

conductor. If repair or replacement of

the electrical cord or plug is necessary,

do not connect the equipment-grounding

conductor to a live terminal.

5. CHECK WITH A QUALIFIED ELECTRICIAN

or service personnel if the grounding

instructions are not completely understood,

or if in doubt as to whether the tool is

properly grounded.

6. USE ONLY 3-WIRE EXTENSION CORDS that

have 3-prong grounding plugs and 3-pole

receptacles that accept the tile saw’s plug.

7. REPAIR OR REPLACE DAMAGED OR WORN

CORD IMMEDIATELY.

8. IF THE PLUG OR RECEPTACLE DOES

GET WET, DO NOT UNPLUG THE CORD.

Disconnect the fuse or circuit breaker that

supplies power to the tool. Then, unplug

and examine for presence of water in the

receptacle.

9. ONLY UL-LISTED EXTENSION CORDS

SHOULD BE USED WITH THIS PRODUCT.

10. IMPROPER USE OF EXTENSION CORDS

MAY CAUSE INEFFICIENT OPERATION

OF YOUR TOOL, which can result in

overheating. Be sure your extension cord

is rated to allow sufﬁcient current ﬂow to

the motor. For the proper gauge for this tile

saw, please refer to TABLE 1 (page 4).

11. DO NOT LET YOUR FINGERS TOUCH THE

TERMINALS of plug when installing or

removing the plug to or from the outlet.

12. THIS TILE SAW MUST BE PROPERLY

GROUNDED. The risk of electric shock

and bodily injury are greatly increased if

it is not, particularly when used in damp

locations or in proximity to plumbing.

NOTE: This saw is intended for use on

a circuit that has a grounded outlet box

like the one illustrated in FIGURE 2 (B).

This saw has a grounding plug that looks

like the one illustrated in FIGURE 2 (A).

Metal

screw

(B) Grounded

outlet box

(A) Grounding pin

FIGURE 2

EXTENSION CORDS

1. Use only extension cords that are intended

for outdoor use. These extension cords are

identiﬁed by a marking “Acceptable for

use with outdoor appliances: store indoors

while not in use.” Use only extension cords

having an electrical rating not less than the

rating of the product. Do not use damaged

extension cords. Examine extension cord

before using and replace if damaged. Do

not abuse extension cords and do not

yank on any cord to disconnect. Keep cord

away from heat and sharp edges. Always

disconnect the extension cord from the

receptacle before disconnecting the product

from the extension cord.

– 4 –

TO REDUCE THE RISK

OF ELECTROCUTION, KEEP ALL CONNECTIONS

DRY AND OFF THE GROUND. DO NOT TOUCH

PLUG WITH WET HANDS.

2. Ground Fault Circuit Interrupter (GFCI)

protection should be provided on the circuit(s)

or outlet(s) to be used for the tile saw.

Receptacles are available having built-in GFCI

protection and may be used for this measure

of safety.

3. USE PROPER EXTENSION CORD. Make

sure your extension cord is in good condition.

When using an extension cord, be sure to use

a cord heavy enough to carry the current your

product will draw. An undersized cord will

cause a drop in line voltage, resulting in loss

power and overheating. TABLE 1 shows the

correct size to use depending on cord length

and nameplate ampere rating. If in doubt, use

the next heavier gauge. The smaller the gauge

number, the heavier the cord.

NOTE: When using an extension cord, ensure

all cords are no smaller than #12 gauge, rated

at a 20-amp minimum, and equipped with

3-prong plugs. Use of anything smaller may

result in overheating or burn out of the motor. It

is recommended to have an electrician check

the voltage at the saw motor to ensure proper

voltage to run the saw efﬁciently and safely.

CALIFORNIA

PROPOSITION 65

SOME DUST CREATED

BY POWER SANDING, SAWING, GRINDING,

DRILLING AND OTHER CONSTRUCTION

ACTIVITIES CONTAIN CHEMICALS KNOWN

TO THE STATE OF CALIFORNIA TO CAUSE

CANCER, BIRTH DEFECTS OR OTHER

REPRODUCTIVE HARM.

Some examples of these chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks, cement and other

masonry products

• Arsenic and chromium from chemically-treated

lumber

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in well

ventilated area, and work with approved safety

equipment, such as those dust masks that are

speciﬁcally designed to ﬁlter out microscopic

particles.

DESCRIPTION

Before attempting to use any tool, be sure to

familiarize yourself with all the operating features

and safety instructions.

KNOW YOUR SAW

Your tile saw has many built-in features for fast,

efﬁcient cutting of ceramic, porcelain, marble,

slate or limestone wall or ﬂoor tile. The durable 7

inch blade cuts tile up to 1-1/8 in. (29 mm) thick.

The adjustable rip and angle guides allow 90° rip

cuts and 22.5°or 45° angle cuts on both the right

and left sides. The right cutting table is hinged so

it can be adjusted for 15°, 30° and 45° miter cuts.

The right table has a built-in water reservoir for

cooling the blade.

Ampere rating

Volts Total length of cord in feet

120 V 25 ft. 50 ft. 100 ft. 150 ft.

240 V 50 ft. 100 ft. 200 ft. 300 ft.

More than No more than AWG

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not recommended

TABLE 1

– 5 –

PRODUCT SPECIFICATIONS

Input: 6.5 Amps

No-load Speed: 3600 RPM

Output: 1-Peak HP

Blade Diameter: 7 in. (180 mm)

Arbor: 5/8 in.

Rating: 120 Volts~60 Hz AC

Depth of Cut: 1-1/8 in. (29 mm)

ASSEMBLY

FOLLOW ALL OF THE

ASSEMBLY AND OPERATION INSTRUCTIONS

COMPLETELY BEFORE CONNECTING THE

SAW TO A POWER SOURCE OR TURNING THE

MOTOR ON.

UNPACKING

1. Remove all packing materials from around

your saw.

2. Carefully lift the saw from carton and place

it on a level work surface.

3. Do not discard the packing materials until

you have carefully inspected the saw for

loose or damaged parts.

The following items are included in box with

your tile saw:

• Tile Wet Saw

• 7 in. Diamond Blade

• Blade guard

• Rip Guide

• Angle Cutting Guide

• Owner’s Manual

4. Inspect the saw carefully to make sure

that no breakage or damage has occurred

during shipping. If any parts are damaged or

missing, please call QEP Customer Service

at 866-435-8665

IF ANY PARTS ARE

DAMAGED OR MISSING, DO NOT ATTEMPT

TO OPERATE THIS SAW. OPERATING THIS

SAW WITH DAMAGED OR MISSING PARTS

COULD RESULT IN POSSIBLE SERIOUS

PERSONAL INJURY.

INSTALLING THE BLADE

1. Remove right cutting table.

2. Remove bafﬂe (see FIGURE 4)

FIGURE 3

– 6 –

FIGURE 4

3. Remove blade shaft nut and outer ﬂange.

4. Carefully place the blade onto the shaft and

push it against the inner ﬂange.

5. Be sure the side of the blade with the

directional arrow is facing towards you.

6. Place the outer ﬂange and the blade shaft

nut onto blade.

7. Hold blade and ﬁrmly tighten the blade shaft

nut with the included wrench, but do not

over tighten (see FIGURE 5).

FIGURE 5

8. Replace bafﬂe and right cutting table.

USE ONLY

CONTINUOUS RIM BLADES WITH THIS SAW.

DO NOT USE SEGMENTED, “TURBO” BLADES,

WOOD SAWING BLADES, BLADES WITH

OPENINGS, OR ANY OTHER CUTTING DEVICES

WITH THIS TILE SAW. USING THESE BLADES

COULD RESULT IN SERIOUS PERSONAL

INJURY AND DAMAGE TO THE SAW.

INSTALLING THE BLADE GUARD

1. Remove the 2 screws on top of the table,

behind the blade slot.

2. Insert blade guard support to align with the

holes where the screws were removed. Adjust

the blade guard support so that the support

aligns with the blade.

3. Insert the 2 screws and tighten (see

FIGURE 6).

FIGURE 6

3. Slip the back end of the blade guard down

over the blade guard support (see FIGURE 7).

4. Replace the knob into the blade guard, while

being careful to hold bolt on the right side in

place, then tighten (see FIGURE 7).

FIGURE 7

5. It is suggested that the front of the blade

guard be pointed slightly down to minimize

the front splash during cutting.

INSTALLING THE RIP GUIDE

1. Slip the back of the rip guide on the back

edge of the table (see FIGURE 8)

2. Place front of rip guide down on the front

edge of the saw.

3. Adjust position to the size of the cut needed,

and ﬂip down lever to lock rip guide in place.

(see FIGURE 9)

4. The round knob over the lever is also used

to further tighten the rip guide.

PINCH POINT.

KEEP HANDS CLEAR OF HINGED LEVER WHEN

LOCKING AND UNLOCKING RIP GUIDE.

– 7 –

FIGURE 8

FIGURE 9

INSTALLING THE ANGLE GUIDE

1. The angle guide is designed to ﬁt on top of the

rip guide. Simply place angle guide onto the

top of the rip guide. (see FIGURE 10)

NOTE: The angle and rip guides can be placed on

either the left or right side.

FIGURE 10

OPERATION

IMPORTANT: ALWAYS turn off the saw and

remove the plug from the outlet BEFORE adding

or removing accessories and making adjust-

ments.

FAILURE TO UNPLUG

THE SAW COULD RESULT IN ACCIDENTAL

STARTING CAUSING POSSIBLE SERIOUS

PERSONAL INJURY.

BEFORE STARTING THE SAW

1. Make sure saw is unplugged.

2. Remove the right cutting table, secure the

waterplug and ﬁll the water reservoir to the

ﬁll line (see FIGURE 11). Do not ﬁll above this

level.

NOTE: ALWAYS keep enough water in the

reservoir when operating the saw. DO NOT let

the saw run dry.

3. Re-attach and close right cutting table.

IMPORTANT: ALWAYS completely drain the

water reservoir and clean thoroughly after

each use.

FIGURE 11

TO START THE SAW

1. Remove cord from side compartment and

connect it to a GFCI (Ground Fault Circuit

Interrupter) protected outlet

(See FIGURE 12)

3.Push On/Off switch to the “On” position.

FIGURE 12

– 8 –

2. Create “drip loop” in the cord (see FIGURE 13)

FIGURE 13

MAKING CUTS

The edge of the cutting table has easy-to-see

dimensions (in both inches and centimeters)

for cutting accuracy.

IMPORTANT: ALWAYS LET THE BLADE CUT AT

ITS OWN SPEED. DO NOT FORCE THE MATERIAL

BEING CUT. ALWAYS CHECK THE BLADE FOR

CRACKS OR DAMAGE BEFORE EACH USE.

MAKING 90° RIP CUTS

1. Install the rip guide by placing it at the

desired position according to the width of

the cut you are making.

2. Place the material to be cut against the

rip guide.

3. Carefully and slowly feed the material into

the blade (see FIGURE 14).

4. If necessary, the rip guide can be removed

when cutting large format tile.

FIGURE 14

MAKING 22.5° & 45° ANGLE CUTS

1. Place the angle guide on the top of the

rip guide.

2. Loosen knob. Position guide to desired

angle (22.5° & 45°) and place tile in guide.

3. Carefully push the angle guide and material

towards the blade (see FIGURE 15).

FIGURE 15

MAKING 15°, 30° & 45° MITER CUTS

(see FIGURE 16)

1. The right cutting table can be angled at 15° or

30° or 45°.

2. Two braces under the table unfold to support

the table at the desired angle.

3. Place the material to be cut onto the right

cutting table.

4. Carefully and slowly feed material into the

blade.

FIGURE 16

FOLDING BENCH STOP

(see FIGURE 17)

1. Convenient Bench Stop keeps saw in place

while making cuts.

FIGURE 17

– 9 –

MAINTENANCE

TO AVOID ACCIDENTS,

ALWAYS DISCONNECT THE TOOL FROM

THE POWER SOURCE BEFORE CLEANING OR

PERFORMING ANY MAINTENANCE

Please do not try to service this machine on

your own.

Avoid using solvents when cleaning plastic

parts. Most plastics are susceptible to damage

from various types of commercial solvents

and may be damaged by their use. Use clean

cloths to remove dirt, carbon dust, etc.

DO NOT AT ANY TIME

LET BRAKE FLUIDS, GASOLINE, PETROLEUM-

BASED PRODUCTS, PENETRATING OILS, ETC.

COME IN CONTACT WITH PLASTIC PARTS.

THEY CONTAIN CHEMICALS THAT CAN

DAMAGE, WEAKEN OR DESTROY PLASTIC.

1. ALWAYS clean the tile saw after each use

and store it in a dry location.

2. ALWAYS wipe off all exterior surfaces and

keep the cutting table clean and free of

all debris.

3. ALWAYS check the blade for cracks or

damage BEFORE each use.

4. ALWAYS store the cord in the compartment

underneath the saw after each use.

DIAMOND BLADES

• Use only 7 in. (180 mm) continuous rim

diamond blades with a 5/8" arbor opening in

this saw. Failure to do so may result in severe

bodily injury and damage to the saw.

DIAMOND BLADE DO’S & DON’TS

1. DO inspect blades daily for cracks or uneven

wear. Discard cracked, chipped or bent

blades!

2. DO use manufacturer’s recommendation

for matching the right blade with the right

material being cut.

3. DO inspect the arbor shaft for uneven wear

before mounting the blade.

4. DO use blades with the correct arbor size on

a compatible arbor shaft.

5. DO ensure the blade is mounted with the

rotation arrow in the proper direction and is

securely tightened with a wrench.

6. DO wear proper safety equipment at all

times when operating the saw. Wear

goggles and dust mask at all times when

operating saw.

7. DO periodically check the blade for cracks

or bond fatigue.

8. DO ensure that blade is traveling through

water reservoir for wet cutting.

9. DO NOT operate the saw without all safety

guards in position.

10. DO NOT operate the saw with blades larger

or smaller than recommended.

11. DO NOT use blades not recommended for

wet cuts.

12. DO NOT exceed maximum RPMs

recommended by the blade manufacturer.

13. DO NOT force the material into the blade.

Let the blade cut at its own speed.

14. DO NOT cut material not recommended by

the blade manufacturer.

TROUBLESHOOTING

OVERHEATING OF SAW:

1. Turn saw off and let it rest until motor is cool

to the touch.

2. Check and clean the ventilation slots,

removing blockage and dirt.

THE SAW DOES NOT START:

1. Check that power cord is properly

plugged in.

2. Check outlet power source and circuit

breaker.

3. Check that UL -Listed extension cord is in

working order if used.

Q.E.P. CUSTOMER SERVICE:

1-866-435-8665

– 10 –

PARTS LIST

See exploded parts (p. 11)

PART # DESCRIPTION Qty

1

Knob of Angle Guide 1

2

Angle Guide 1

3

Base of Angle Guide 1

4

Nut (M6) 2

5

Shank w/ Square Neck 1

6

Shank Sleeve 1

7

Cam 1

8

Spanner of Rip Guide 1

9

Elastic Pin (3x25) 1

10

Holddown Block 1

11

Round Pin 2

12

Rip Guide 1

13

Compression Spring 1

14

Anti-Slip Pad 1

15

Block of Rip Guide 1

16

Measure Guide (A) 1

17

Handle Grip (Upper) 1

18

Master Table 1

19

Measure Guide (B) 1

20

Knob of Blade Guard 1

21

Blade Guard 1

22

Bracket of Blade Guard 1

23 Cross Recessed Pan Head Screw

(M5X10)

4

24

Right Table 1

25

Positioning Spring of Right Table 1

26

Elastic Washer 5 1

27 Cross Recessed Countersunk Head

Screw (M5X10)

1

28

Miter Table Support 1

29

Side Spray Bafﬂe 1

30 Cross Recessed Pan Head Tapping

Screw (ST4.2x15)

13

31

Spray Bafﬂe 1

32

Capacitor 1

33

Capacitor Clamp 1

34 Cross Recessed Countersunk Tapping

Head Screw (ST4.2X15)

4

35 Cross Recessed Countersunk Tapping

Head Screw (ST2.9x15)

2

PART # DESCRIPTION Qty

36

Handle Grip (Lower) 1

37

Cover of Motor 1

38

Wind Guard Board 1

39

Fixing Clip of Cord 1

40

Base 1

41

Nut 1

42

Outer Flange 1

6-7003Q

7" Continuous Rim Diamond Blade 1

44

Inner Flange 1

45

Sealing Pad 1

46

Outer Hexagon Screw (M5 x 15) 2

47

Flat Washer 5 2

48

Water Proof Washer 2

49 Cross Recessed Tapping Screw

(ST4.2x30)

4

50 Cross Recessed Pan Head Screw

(M4x8)

1

51

Elastic Washer 5 1

52

Lock washers internal Teeth 1

53

Motor 1

54

Power Cord 1

55

Power Cord Storage Rack 1

56

Plate of Switch Protection 1

57

Overload Protector 1

58 Water-Proof Cap of Overload

Protector

1

59

Switch Protector 1

60

Switch 1

61

Rubber Washer 4

62

Flat Washer 8 4

63

Inner Hexagonal Bolt M8x18 4

64

Feet 4

65

Bast of Feet 4

66

Anti-Bending Sleeve 1

67

Block of Bench Stop 1

68

Bench Stop 1

69

Fix Cap of Plug 1

70

Plug 1

71

O-Shaped Seal Loop 1

Page is loading ...

QEP 22900Q User manual

QEP 22900Q User manual

in other languages

Related papers

Other documents