Parts for Cloud Raptor
Centre box. Side woods for centre box. Wood parts for motor. Wood for F3 ight control. Stickers for ESC & battery. Control horns for aileron.
Wings x 2 Small wings of the wing side. Wood for center box. Wood for FPV. Extension wire for motor. Heat shrinkable tube.
Aileron x 2 The magnet locates the piece of wood. Wood for center box bottom. Center box Carbon and push plug carbon
rod.
Sticker for ight contrail. Z bend.
Magnets.
Foam Glue.
1. Install the center side board of the
engine room, evenly spread glue on
side board and side of engine room
box.
In the following picture the part is glued
together.
2. Connect he carbon rod and wing.
Apply glue to the three surfaces
indicated by the arrow below and stick
together.
3. The assembly of wing precautions is
shown in the picture.
Pay special attention to the front edge
of the wing. It must be directed toward
the hole in the side panel of the center
box, because the wings need to be
assembled at correct angle.
4. Assemble the wing and the carbon
rod from left wing hole to the center
box slot and to the right wing hole for
carbon. Glue them!
5. After bonding, the picture is shown
below.
6. Assemble the motor seat and apply
glue to the edge of the board.
Assemble the motor seat as shown.
7. Assembly of motor seat precautions. 8. Assemble the camera to x the board. After assembly, the following head is
shown.
Installation and operating instructions
Unbreakable foam FPV wing cloud raptor kit
Item no. 1590611
Intended use
This product is a model aircraft. It is suitable for outdoor use and designed for model aircraft
beginners.
You can install compatible electrical drive and control components in the model. These are not
included with the product. A sample conguration of optional components is provided in the
instructions. However, the actual conguration may vary depending on the components used.
Please refer to the technical data when purchasing optional components.
Read the assembly and operating instructions carefully and store them in a safe place.
Make this product available to third parties only together with its operating instructions. This
product complies with statutory national and European regulations. All company and product
names are trademarks of their respective owners. All rights reserved.
Download the latest instructions at www.conrad.com/downloads or scan the
QR code on this page. Follow the instructions on the website.
Symbols
The symbol with the exclamation mark in the triangle is used to highlight important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on how to use the
product.
Safety instructions
The product is not suitable for children under 14 years of age.
Read the instructions and safety information carefully. If you do not follow the
safety instructions and information on proper handling in this manual, we will
assume no liability for any resulting personal injury or damage to property. Such
cases will invalidate the warranty/guarantee.
You are solely responsible for the safe operation of this model!
• This product is not a toy. Keep it out of the reach of children and pets.
• Do not leave the packaging lying around carelessly, as it may become dangerous playing
material for children. Keep small parts out of the reach of children!
• When assembling the model, take care not to injure yourself on sharp edges or pointed ends.
• This model has the potential to cause damage to property and/or individuals. Make sure that
you are sufciently insured, e.g. by taking out private liability insurance. If you already have
such a policy, check with your insurance company that the use of this model is covered by the
policy. In some EU countries, you are required to have insurance when using a model aircraft.
• The product must not become damp or wet.
• Improper use can cause serious damage to people and property! Ensure that you maintain a
sufcient distance from peoples, animals and objects.
• Select a suitable location to y the model aircraft.
• Only y the model when you are fully alert and able to respond. Fatigue, alcohol and medication
can can affect your ability to respond.
• Do not direct the model towards spectators or towards yourself.
• Please refer to the manufacturer‘s safety and installation instructions when installing electrical
components.
If you have questions which remain unanswered by these instructions, contact our
technical support service or other technical personnel.
Disposal
Always dispose of the product according to the relevant statutory regulations.
You thus fulll your statutory obligations and contribute to the protection of the environment.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopy, microlming, or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication represents the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE. *1590611_v1_0817_02_DS_m_gb_(1)
9. Assemble the magnetic patch in the
step of the engine room. The rst
choice is to use the magnet limit wood
bar to draw a circle in the engine
room, and the small iron sheet will be
installed with glue.
Then apply the magnet board and the top
edge of the cabin to glue the magnet and
the magnet, as shown below.
10. Assembly gaps in the cabin cover.
Assembly the slit wood bar as shown
below.
11. Assemble the servos. Before the
servos assembly, it will need to give
power and reset the position then
assemble the ctrl arm. This step can
also be carried out before attaching
the wings, and the servo line will be
worn out through the perforated hole.
After the assembly, the following diagram
is shown, the left and right servo are
assembled in the same way.
12. Install aileron and the small wing,
install aileron at the edge of the ap
and then glue to the wing.
Install as shown in the picture.
13. After the motor is soldered to
the extension cord, the motor is
assembled in the motor seat. Note
that the welding motor extension cord
should be staggered and welded. After
the wrong welding, no heat shrinkable
sleeve is used, so as to facilitate the
installation of wood strip in the back of
the engine room.
14. Install the ctrl horn and ctrl push rod,
and then glue the motor seat to the
center of the center box.
15. Assemble the push rod for ailerons,
then install it to the fuselage.
Heat shrink to connect the carbon
ber rod and Z bend. You must glue
them to be safer.
Assemble as shown below.
16. Put the wire into the trunking. And
glue the wood.
17. If you went to y FPV, please do after
step. Solder ESC to the power supply
board.
18. Solder the ight control and receiver,
and soldering Row needles.
Do not short-circuit!
19. Connect the Flight control and Power
supply board by Nylon screw.
20. Glue them on the wood.
21. Glue them in the center box.
22. Installation of the camera
23. Install and x the receiver, battery,
image transmission and other
equipment.
Recommended electronics (optional):
• Motor: 2205 2300kv
• Servo: 9 g * 2
• Esc: 30 A and 2 A BEC
• Prop: 0545
• Battery: 4S 500 mAh
• Motor: 2815 (2207) 1450kv
• Servo: 9 g * 2
• Esc: 12 A and 2 A bec
• Prop: 0843
• Battery: 3S 850-1300 mAh
Technical Data
Weight .......................................... 212 g
Wing span ..................................... 100 cm
Material ......................................... PP
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
ROBBE Arcus II 2649 Instruction And User's Manual
-
REPTILE HARRIER S1100 User manual
-
-
Black Horse Model BH63 Instruction Manual Book
-
E-flite Super Cub 25e ARF Assembly Manual
-
APC EP Zero ARF User manual
-
-
Tower Hobbies Ultimate Bipe GP/EP ARF User manual
-
Premier Ventique 60e Assembly Manual
-
SIG SIGRC107EPARF User manual
