1. Skyline parts.
2. Glue the body. Apply glue evenly to the
fuselage and the body for 3 minutes.
3. Assemble the carbon for main wing.
Cut the main wing following the line on
the wing’s back. Use a lighter to heat
the blade. So the cut will have a x
carbon thickness seam.
Glue the carbon in that seam.
4. Glue the main wing with glue or hot
melt glue. Apply glue on the bonding
surface. If you use foam glue, let it
cure for more than 5 minutes before
you put the pieces together. If you use
hot melt glue, glue instantly. The angle
on the one side wing must not be
greater than 3 degrees.
After bonding, your model should look
like this.
5. Glue the carbon of the fuselage. Apply
glue to the adhesive surface of the
square carbon pipe. Glue the surface
of the body under the fuselage. Wait
for 3 minutes. The carbon bar front end
should be in the middle of the white
area of the nose.
Side
Bottom
6. Assemble the at tail reinforcing
carbon sheet. Reinforce the carbon
sheet to be bonded to the opening side
of the slot. Apply glue to the carbon
lm and the end glue joint, and put it in
place for 3 minutes.
7. Stick the carbon rod to the horizontal
tail, take the middle position in the
horizontal tail. Apply the glue to the
corresponding bonding position and
press together.
8. Assemble the vertical tail n. Apply
glue to the face of the vertical n and
apply evenly on the area of the carbon
rod. Wait for 3 min and x the 2 sides
together.
After bonding, pay attention to the position
of the hinge cutting position of the vertical
tail and the alignment of the edge of the
carbon tube and that they do not affect
horizontal tail movement.
9. To make the landing gear cut the
landing gear white from the middle with
scissors The two white crescent teeth
are the landing gear. The carbon rod
and landing gear are reinforced with
glue and shing line.
Make a landing gear as shown below.
10. The wing is attached to the fuselage
and the landing gear is assembled.
The landing gear is supported and
the wings are supported. Glue on the
wing and fuselage and leave for more
than 5 minutes.
11. Assemble the landing gear
reinforcement. First x the landing
gear carbon bar intersections with
a bit of glue, or hot melt glue in the
landing gear wood chip. Then apply
glue to the fuselage for adhesion.
The landing gear reinforcement plate is
attached as shown in the gure below.
Installation and operating instructions
Unbreakable foam model aircraft (Skyline)
Item no. 1590613
Intended use
This product is a model aircraft. It is suitable for outdoor use and designed for model aircraft
beginners.
You can install compatible electrical drive and control components in the model. These are not
included with the product. A sample conguration of optional components is provided in the
instructions. However, the actual conguration may vary depending on the components used.
Please refer to the technical data when purchasing optional components.
Read the assembly and operating instructions carefully and store them in a safe place.
Make this product available to third parties only together with its operating instructions. This
product complies with statutory national and European regulations. All company and product
names are trademarks of their respective owners. All rights reserved.
Download the latest instructions at www.conrad.com/downloads or scan the
QR code on this page. Follow the instructions on the website.
Symbols
The symbol with the exclamation mark in the triangle is used to highlight important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on how to use the
product.
Safety instructions
The product is not suitable for children under 14 years of age.
Read the instructions and safety information carefully. If you do not follow the
safety instructions and information on proper handling in this manual, we will
assume no liability for any resulting personal injury or damage to property. Such
cases will invalidate the warranty/guarantee.
You are solely responsible for the safe operation of this model!
• This product is not a toy. Keep it out of the reach of children and pets.
• Do not leave the packaging lying around carelessly, as it may become dangerous playing
material for children. Keep small parts out of the reach of children!
• When assembling the model, take care not to injure yourself on sharp edges or pointed ends.
• This model has the potential to cause damage to property and/or individuals. Make sure that
you are sufciently insured, e.g. by taking out private liability insurance. If you already have
such a policy, check with your insurance company that the use of this model is covered by the
policy. In some EU countries, you are required to have insurance when using a model aircraft.
• The product must not become damp or wet.
• Improper use can cause serious damage to people and property! Ensure that you maintain a
sufcient distance from peoples, animals and objects.
• Select a suitable location to y the model aircraft.
• Only y the model when you are fully alert and able to respond. Fatigue, alcohol and medication
can can affect your ability to respond.
• Do not direct the model towards spectators or towards yourself.
• Please refer to the manufacturer‘s safety and installation instructions when installing electrical
components.
If you have questions which remain unanswered by these instructions, contact our
technical support service or other technical personnel.
Disposal
Always dispose of the product according to the relevant statutory regulations.
You thus fulll your statutory obligations and contribute to the protection of the environment.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopy, microlming, or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication represents the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE. *1590613_v1_0817_02_DS_m_gb_(1)
12. To make the tail slip, nd the small
triangle and 5 mm end carbon slice.
Glue as shown below.
Apply the glue on the fuselage carbon
stick to the surface. Then put the glue
on the surface of the sliding surface and
then x it after 3 minutes. The assembly
looks like shown following picture.
13. Fix the motor to the motor wood with
screws
14. Solder the motor ESC and JST
After soldering the completed assembly
is shown in the following picture.
15. Glue the motor to the fuselage. Glue
the motor wood and to the fuselage
waiting for more than 5 minutes for
the glue to dry.
After bonding, the model should look like
shown in the below picture.
16. Assemble the rudder ctrl horn. Apply
the right amount of glue to the rudder
horn and insert the corresponding
rudder horn to tighten the tiller.
Install vertical rudder horn and quick
adjust screw. The small nut needs to be a
thread xing agent or a small amount of
glue to prevent the small nut from falling
off. Fix the carbon rod of the screw to
wait for the rod to insert after assembly.
Assemble the horn for horizontal tail in
the same manner.
Assemble the horn for aileron in the
same manner.
17. If you assemble the servos, you must
add the power to these servo to reset
the servo’s position to center.
Assemble the aileron servo. Insert
the servo of the aileron into the aps
following the picture.
The upper hole is for the aileron servo.
The aileron servo needs servo’s arm at
upside rudder and lifter steering gear and
head down to install.
18. Assemble the push ctrl rod for aileron.
First add some glue to the carbon tip
and use the heat-shrinkable tubing
cover the z bend and carbon. Use
light heat to shrink.
19. Assemble the aileron push rod.
Connect the z-bend to the servo arm,
other end in to the fast adjust screw
hole and add a small screw on it. Be
careful not to push too hard. Avoid
damaging the carbon rods.
20. Assemble the rudder and elevator
servo. Glue two servos.
21. Glue them into the body’s hole the
servo’s head down.
23. Add glue to the carbon tip, and use
the heat-shrinkable tubing cover the z
bend and carbon. Use light heat. Note
that using a lighter to heat up the heat
shrinkable tube should be insulated with
white paper to prevent the aircraft from
damage.
24. The elevator and rudder are done as
shown below.
25. Fix the esc and receiver, collate wiring
harness.
You can x battery with a magic stick. The
center of gravity is in the rst third of the
wing‘s total width.
22. Assemble the rudder and elevator ctrl
push rod. First, nd the 1.5mm long
pull rod and pull the rod through the
hole in the side of the motor wood.
The end cross the fast adjust screw hole.
Recommended electronics (optional):
• Motor: 1806 2300 kv
• Servo: 9 g * 3
• Esc: 12 A and 2 A bec
• Prop: 0545
• Battery: 2s 500-800 mah, 3s 400-550 mah
Technical Data
Weight .......................................... 118 g
Wing span ..................................... 78 cm
Material ......................................... PP
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
MinimumRC Minimum RC J3-Cub Owner's manual
-
Kyosho EPP Yak-54 ARF User manual
-
Stevens AeroModel XS480 Product Support
-
Vigorkiy rc hobby SUPER EXTRA330SC User manual
-
E-flite 4-Site Assembly Manual
-
Carf-Models CL-41 Tutor User manual
-
-
-
AeroWorks YAK 54 ARF-QB Assembly Manual
-
