Reely 1590611 Operating instructions

Brand: Reely

Model: 1590611

Type: Operating instructions

Parts for Cloud Raptor

Centre box. Side woods for centre box. Wood parts for motor. Wood for F3 ight control. Stickers for ESC & battery. Control horns for aileron.

Wings x 2 Small wings of the wing side. Wood for center box. Wood for FPV. Extension wire for motor. Heat shrinkable tube.

Aileron x 2 The magnet locates the piece of wood. Wood for center box bottom. Center box Carbon and push plug carbon

rod.

Sticker for ight contrail. Z bend.

Magnets.

Foam Glue.

1. Install the center side board of the

engine room, evenly spread glue on

side board and side of engine room

box.

In the following picture the part is glued

together.

2. Connect he carbon rod and wing.

Apply glue to the three surfaces

indicated by the arrow below and stick

together.

3. The assembly of wing precautions is

shown in the picture.

Pay special attention to the front edge

of the wing. It must be directed toward

the hole in the side panel of the center

box, because the wings need to be

assembled at correct angle.

4. Assemble the wing and the carbon

rod from left wing hole to the center

box slot and to the right wing hole for

carbon. Glue them!

5. After bonding, the picture is shown

below.

6. Assemble the motor seat and apply

glue to the edge of the board.

Assemble the motor seat as shown.

7. Assembly of motor seat precautions. 8. Assemble the camera to x the board. After assembly, the following head is

shown.

Installation and operating instructions

Unbreakable foam FPV wing cloud raptor kit

Item no. 1590611

Intended use

This product is a model aircraft. It is suitable for outdoor use and designed for model aircraft

beginners.

You can install compatible electrical drive and control components in the model. These are not

included with the product. A sample conguration of optional components is provided in the

instructions. However, the actual conguration may vary depending on the components used.

Please refer to the technical data when purchasing optional components.

Read the assembly and operating instructions carefully and store them in a safe place.

Make this product available to third parties only together with its operating instructions. This

product complies with statutory national and European regulations. All company and product

Download the latest instructions at www.conrad.com/downloads or scan the

QR code on this page. Follow the instructions on the website.

Symbols

The symbol with the exclamation mark in the triangle is used to highlight important

information in these operating instructions. Always read this information carefully.

The arrow symbol indicates special information and advice on how to use the

product.

Safety instructions

The product is not suitable for children under 14 years of age.

Read the instructions and safety information carefully. If you do not follow the

safety instructions and information on proper handling in this manual, we will

assume no liability for any resulting personal injury or damage to property. Such

cases will invalidate the warranty/guarantee.

You are solely responsible for the safe operation of this model!

• This product is not a toy. Keep it out of the reach of children and pets.

• Do not leave the packaging lying around carelessly, as it may become dangerous playing

material for children. Keep small parts out of the reach of children!

• When assembling the model, take care not to injure yourself on sharp edges or pointed ends.

• This model has the potential to cause damage to property and/or individuals. Make sure that

you are sufciently insured, e.g. by taking out private liability insurance. If you already have

such a policy, check with your insurance company that the use of this model is covered by the

policy. In some EU countries, you are required to have insurance when using a model aircraft.

• The product must not become damp or wet.

• Improper use can cause serious damage to people and property! Ensure that you maintain a

sufcient distance from peoples, animals and objects.

• Select a suitable location to y the model aircraft.

• Only y the model when you are fully alert and able to respond. Fatigue, alcohol and medication

can can affect your ability to respond.

• Do not direct the model towards spectators or towards yourself.

• Please refer to the manufacturer‘s safety and installation instructions when installing electrical

components.

If you have questions which remain unanswered by these instructions, contact our

technical support service or other technical personnel.

Disposal

Always dispose of the product according to the relevant statutory regulations.

You thus fulll your statutory obligations and contribute to the protection of the environment.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method (e.g. photocopy, microlming, or the capture in

electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.

This publication represents the technical status at the time of printing.

9. Assemble the magnetic patch in the

step of the engine room. The rst

choice is to use the magnet limit wood

bar to draw a circle in the engine

room, and the small iron sheet will be

installed with glue.

Then apply the magnet board and the top

edge of the cabin to glue the magnet and

the magnet, as shown below.

10. Assembly gaps in the cabin cover.

Assembly the slit wood bar as shown

below.

11. Assemble the servos. Before the

servos assembly, it will need to give

power and reset the position then

assemble the ctrl arm. This step can

also be carried out before attaching

the wings, and the servo line will be

worn out through the perforated hole.

After the assembly, the following diagram

is shown, the left and right servo are

assembled in the same way.

12. Install aileron and the small wing,

install aileron at the edge of the ap

and then glue to the wing.

Install as shown in the picture.

13. After the motor is soldered to

the extension cord, the motor is

assembled in the motor seat. Note

that the welding motor extension cord

should be staggered and welded. After

the wrong welding, no heat shrinkable

sleeve is used, so as to facilitate the

installation of wood strip in the back of

the engine room.

14. Install the ctrl horn and ctrl push rod,

and then glue the motor seat to the

center of the center box.

15. Assemble the push rod for ailerons,

then install it to the fuselage.

Heat shrink to connect the carbon

ber rod and Z bend. You must glue

them to be safer.

Assemble as shown below.

16. Put the wire into the trunking. And

glue the wood.

17. If you went to y FPV, please do after

step. Solder ESC to the power supply

board.

18. Solder the ight control and receiver,

and soldering Row needles.

Do not short-circuit!

19. Connect the Flight control and Power

supply board by Nylon screw.

20. Glue them on the wood.

21. Glue them in the center box.

22. Installation of the camera

23. Install and x the receiver, battery,

image transmission and other

equipment.

Recommended electronics (optional):

• Motor: 2205 2300kv

• Servo: 9 g * 2

• Esc: 30 A and 2 A BEC

• Prop: 0545

• Battery: 4S 500 mAh

• Motor: 2815 (2207) 1450kv

• Servo: 9 g * 2

• Esc: 12 A and 2 A bec

• Prop: 0843

• Battery: 3S 850-1300 mAh

Technical Data

Weight .......................................... 212 g

Wing span ..................................... 100 cm

Material ......................................... PP

Reely 1590611 Operating instructions

Brand: Reely

Model: 1590611

Type: Operating instructions

Download PDF

report

Reely 1590611 Operating instructions

Reely 1590611 Operating instructions

Related papers

Other documents