Kichler Lighting 49860BKT User manual

Brand
Kichler Lighting
Model
49860BKT
Type
User manual
Date Issued: 07/26/17 IS-49860-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
1) Slip fixture over post and mark position of mounting holes in
post.
2) Remove fixture from post.
3) Drill 3/16” dia holes in post at positions marked .
4) If fixture is provided with ground wire, connect fixture ground
wire to outlet box ground wire with wire connector. (Not
provided). Never connect ground wire to black or white power
supply wires.
5) Grounding instructions: (See Illus. A or B)
A) On fixtures where mounting strap is provided with a
hole and two raise dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On fixtures where a cupped washer is provided. Put
ground wire from outlet box under cupped washer and
green ground screw and thread screw into hole in
mounting strap.
If fixture is provided with ground wire. Connect fixture ground
wire to outlet box ground wire with wire connector, after fol-
lowing the above steps. Never connect ground wire to black or
white power supply wires.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
A
B
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
FINIAL
CAPUCHÓN
WASHER
ARANDELAS
LOWER TRIM
ADORNO INFERIOR
GLASS
VIDRIO
FIXTURE ROOF
TECHNO DE LUMINARIA
UPPER TRIM
ADORNO SUPERIOR
STUD
SOCKET
PORTALÁMPARAS
SCREWS
EMPULGUERAS
POST CUP
TAZA DE POST
WIRE CONNECTORS
CONECTORES DE ALAMBRE
/CLAVO
6) Make wire connections. Reference chart below for correct
connections and wire accordingly.
7) Slip fixture over post and secure in place using provided
screws. Screws should slip into holes drilled in post.
8) Carefully, lower the glass down into the trim with the twist
thread upward. Pass over the socket and rest the bottom of
the glass onto the flat surface.
9) Insert recommended bulb. (Not supplied)
10) Lower the fixture roof down to the cage. Twist the glass into
the fixture roof to secure the glass. DO NOT OVER TIGHTEN.
11) Align the (2) studs on the upper trim with the (2) holes in the
lower trim.
12) Pass the studs through the holes in the lower trim. Slip a
washer onto the stud followed by threading on a finial. Repeat
for remaining studs. Tighten all finials to secure the trim.
CAUTION – RISK OF SHOCK – DISCONNECT POWER
AT THE MAIN CIRCUIT BREAKER PANEL OR MAIN FUSE
BOX BEFORE STARTING AND DURING THE INSTALLATION.
Page is loading ...
Date Issued: 07/26/17 IS-49860-CB
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
1) Slip fixture over post and mark position of mounting holes in
post.
2) Remove fixture from post.
3) Drill 3/16” dia holes in post at positions marked .
4) If fixture is provided with ground wire, connect fixture ground
wire to outlet box ground wire with wire connector. (Not
provided). Never connect ground wire to black or white power
supply wires.
5) Grounding instructions: (See Illus. A or B)
A) On fixtures where mounting strap is provided with a
hole and two raise dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On fixtures where a cupped washer is provided. Put
ground wire from outlet box under cupped washer and
green ground screw and thread screw into hole in
mounting strap.
If fixture is provided with ground wire. Connect fixture ground
wire to outlet box ground wire with wire connector, after fol-
lowing the above steps. Never connect ground wire to black or
white power supply wires.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
A
B
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
FINIAL
ORNEMENT
WASHER
RONDELLE
LOWER TRIM
MOULURE INFÉRIEUR
GLASS
VERRE
FIXTURE ROOF
TOIT DE LUMINAIRE
UPPER TRIM
MOULURE SUPÉRIEURE
STUD
SOCKET
DOUILLE
SCREWS
DES VIS
POST CUP
POST CUP
WIRE CONNECTORS
CONNECTEURS DE FIL
/CLOU
6) Make wire connections. Reference chart below for correct
connections and wire accordingly.
7) Slip fixture over post and secure in place using provided
screws. Screws should slip into holes drilled in post.
8) Carefully, lower the glass down into the trim with the twist
thread upward. Pass over the socket and rest the bottom of
the glass onto the flat surface.
9) Insert recommended bulb. (Not supplied)
10) Lower the fixture roof down to the cage. Twist the glass into
the fixture roof to secure the glass. DO NOT OVER TIGHTEN.
11) Align the (2) studs on the upper trim with the (2) holes in the
lower trim.
12) Pass the studs through the holes in the lower trim. Slip a
washer onto the stud followed by threading on a finial. Repeat
for remaining studs. Tighten all finials to secure the trim.
CAUTION – RISK OF SHOCK – DISCONNECT POWER
AT THE MAIN CIRCUIT BREAKER PANEL OR MAIN FUSE
BOX BEFORE STARTING AND DURING THE INSTALLATION.
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Kichler Lighting 49860BKT User manual

Brand
Kichler Lighting
Model
49860BKT
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents