INSTRUCTION SHEET NO
INSTRUCTIONS PROCEDURE FOR LOW VOLTAGE
FRAME=fN KIT WITH REM~E TRANSFORMER
IS:2000LVNT
0191
Page 1 of 2
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.
This fixture is intended for installation in accordance with the National Electrical Code or local regulations. To
asaure full compliance with local codes and regulations,
check with your local electrical inspector before
installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference
N~E FRAME-fN KIT IS PROVIDED WITHOUT TRANSFORMER. TRANSFORMER MUST BE PROVIDED SY
OTNERB. LIGHlOLIER CAT #B60S AND 8609 TRANSFORMERS MAy BE USED.
CAUTION: THIS FRAME-IN KIT IS RATED AT 42VA. USE ONLY 12V. AC. INPUT.
FIG. A
FIG. B FIG. C
FIG. D
1. FRAME-IN
2. CLOSE-IN
3. SNAPON
4. PUSH-UP
WARNING—(RISK OF FIRE) DO NOT INSTALL INSULATION WITHIN 3 INCHES OF FiXTURE SIDES OR
WIRING COMPARTMENT, NOR ABOVE FIKTURE IN SUCH A MANNER TO ENTRAP HEAT.
1.
2.
3.
4.
FRAME.IN (Fig. A)
Faaten MOUNTING FRAME to wood joist. Line
N~E For wat plaster ceiling, uae Plaster
Ring Accessory No. 1959 (order aaparately).
4&=---- ‘OTO”cL’p
SNAPIN (Fig. C).
I
SEE SEPARATE
REFLECTOR TRIM
PUSH-UP (Fig. D).
INSTRUCTION
SHEETS.
FIG G
SEE BACK PAGE FOR LAMPING INSTRUCTIONS.
LK59-ITC>949
[=@sEcAucus> NEw JERSEY,07096
* MO NT REAL, QUEBEC, C AN ADA
L
~&OOOLVNT
LAMPING
Page 2 of 2
NOTE Socket manufacturers have suggested that
socket may fail after 3 to 6 relampings. If this
occurs socket can be replaced by disconnecting
male connectors (attached to socket leads) from
female connectors (attached to fixture leads) and
1. Make sure that power is OFF when Iamping
or relamping. Remove LAMP RING from
SOCKET CUP by pulling etraight down.
2. Ineeft LAMP @fR-16) between LAMP
SPR NGS until face of lamp sits firmly on
GLASS LAMP GUARD (Fig. l).
3, Attach SOCKET to hi-pin prongs on LAMP
replacing it with a naw socket procured thtiugh
Lightolier (Fig H.).
INSULATINGSLEEVING
MALECONNECTORS
(Altaohedto socketWires)
--
+Q
~ FEMALE CONNECTORS
(Attached to
Fixture V4res)
MR16 SOCKET
L
FIG. H
4. Insert LAMP RING with LAMP and GLASS
LAMP GUARD back into SOCKET CUF!
cf5-’-s0cKET
LAMP
&
-#
- LAMP SPRING
GLASS LAMP
GUARD
LAMP RING
t
FIG. I
AIMING ANGLE ADJU=MENT (Fig. J)
1. For vertical adjustment, insert blade of
screwdriver into the open slot of YOKE.
2. Using the screwdriver as a lever, tilt the entire
LAMP HOLDER to the desired angle.
3. ~~L~#mtal adjustment, rotate tie LAMP
OCKET CUP
LAMP HOLDER
NOTE 1. LOW VOLTAGE FIXTURES should be APERTURE TRIM
dimmed only wNh speciel dimmers intended
ASSEMSLY
specifically for that purpose. Use Llghtoller
Lytemode Scenlst,
Crescendo VA, Neptune VA,
Yo
Preclslon VA,Esayset VA,Sunriee VA,Redlsnt VA or
equivalent products by others ,or verieblo
~,
sutotranaformera or
electronicdlmmeraintendedfor
~.
~.,
usewith lowvoltageflstuma.2. QWvoltsgefixtures
~.y::,?
mey produoe eudible sound when ueed with
dimme~
which may be objectional in acoustically
critical sreaa.
FIG. J
NOTE Followthe mex. wire length recommended
below to minimize voltsge drop. Voltage drop will
affect the brlghtneaa and color of the light.
~
e
/