Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Installation should be done only by qualified personnel and conform to all local codes.
6. Only use installation methods and materials capable of supporting four times the maximum specified load.
7. Only use replacement parts recommended by Pelco.
8. This unit is designed for indoor use only, and it must not be installed where exposed to rain or moisture.
Description
The PMCL-WM1A is a single swing-arm wall mount that used to mount any of Pelco’s 200, 300, or 400 Series flat panel LCD monitors. This mount supports
Pelco 500 Series PMCL524BL and PMCL532BLLCD monitors, although a PMCL-V200 adapter plate is required. The PMCL-WM1A mount can be swiveled 360
degrees to allow you to use your monitor in either landscape or portrait view. The mount also allows you to tilt the monitor 35 degrees for the best viewing
angle. The PMCL-WM1A is capable of supporting a maximum load of 40.8 kg (90 lbs).
MONITORS SUPPORTED
The following monitors are supported by the PMCL-WM1A Monitor Mount:
NOTE: Use the PMCL-V200 adapter plate for installing the mount on monitors larger than 31-inches.
PARTS LIST
The following parts are supplied:
USER-SUPPLIED PARTS LIST
Parts for attaching the wall bracket to the wall are required but not supplied. Lag bolts or anchor bolts are required as specified on the following page for
attaching the wall bracket to the wall. The type of parts the user is required to supply is dependent on the type of wall to which the bracket is installed.
PMCL300 Series
PMCL317BL 432 mm (17 in.) Flat Panel monitor
PMCL319BL 483 mm (19 in.) Flat Panel monitor
PMCL400 Series
PMCL417HB 432 mm (17 in.) High-Bright Flat Panel monitor
PMCL419HB 483 mm (19 in.) High-Bright Flat Panel monitor
PMCL500BL Series
PMCL524BL 610 mm (24 in.) LED Flat Panel monitor
PMCL532BL 813 mm (32 in.) LED Flat Panel monitor
Qty Description
1 PMCL-WM1A Monitor mount
4 M4 x 10 mm pan head Phillips screws, stainless steel
4 Split lock washers
4 M6 x 12 mm pan head Phillips screws, stainless steel
4 Flat washers
1 Allen wrench, 3/16 in.
4 Cable ties, 2 in.
INSTALLATION
PMCL-WM1A Monitor Mount
C2225M-C (10/14)
2 C2225M-C (10/14)
Installation
NOTE: It is recommended that two people install the mount to the wall followed by installation of the monitor onto the mount.
INSTALLING THE MOUNT TO A WOOD STUD WALL
User Supplied Parts: Three lag bolts (5/16-inch diameter x 2-inch), to attach the mounting bracket to the wall.
1. Use a stud finder to locate and mark the edges of the wood stud in which the mount attaches.
2. Center the mounting bracket between the edges of the stud, and use the mounting bracket as a template to mark the mounting holes.
3. At the three marked mounting hole locations, drill 7/32-inch diameter holes 2-inch deep from the wall surface into the wood stud.
4. Attach the wall bracket to the wall securing it to the wood stud using 5/16-inch diameter x 2-inch lag bolts as shown in Figure 1.
INSTALLING THE MOUNT TO A SOLID CONCRETE OR CINDER BLOCK WALL
User Supplied Parts: Three sleeve anchors (ITW Red Head Dynabolt Sleeve Anchor HN-1624), to attach the mounting bracket to the wall.
1. Level and use the mounting bracket as a template to mark the mounting holes on the wall.
2. At the marked hole locations, drill 5/16” diameter holes 2.25-inches deep and clean dust and debris from the holes.
3. Attach the wall bracket to the wall using 5/16-inch diameter x 2.5-inch sleeve anchors as shown in Figure 2.
a. The recommended sleeve anchor for the mounting hole diameter is ITW Red Head Dynabolt Sleeve Anchor HN-1624.
b. Insert a Dynabolt sleeve anchor through each bracket hole. Then insert the anchors into the pre-drilled holes until the sleeve washer and head is
flush with the surface of the wall bracket and the bracket is tight against the wall.
c. Use a wrench to turn the sleeve head clockwise two to three turns to anchor the sleeve in the wall.
WARNING:
• The wood stud must be at least 2-inch x 4-inch.
• The studs must be covered with a maximum 0.5-inch thick layer of wallboard or plywood.
• Always attach the mounting bracket to the wall in a vertical position. This mount is not designed to be
mounted horizontally.
WARNING:
• Do not install hardware into mortar joints in filled or non-filled cinder block walls.
• Concrete must be a minimum of 3600 psi or 25 Mpa density.
• Concrete must be minimum 3-inch thickness or concrete filled cinder block.
Figure 1. Attaching the Mount to Wood Stud Wall Figure 2. Attaching the Mount to Solid Concrete or Cinder Block Wall
WOOD STUD
LAG BOLT
WALL
SLEEVE
ANCHOR
SOLID
CONCRETE
WALL
CINDER BLOCK
WALL
C2225M-C (10/14) 3
INSTALLING THE MONITOR TO THE MOUNT
1. Hold the monitor level with the mount. Attach the monitor mount to the monitor. Refer to Figure 3 and do one of the following:
a. 31-inch Monitor or Smaller: Align the monitor to the correct hole pattern on the mounting plate. Use the M4 x 10 mm screws and split lock
washers (supplied) to secure the monitor to the mounting plate.
or
b. Monitors Larger than 31-inches:
NOTE: Use the PMCL-V200 adapter plate for installing the mount on monitors larger than 31-inches.
Align the monitor to the outside hole pattern of the monitor plate. Use the M6 x 12 mm screws and flat washers (supplied) to secure the monitor
to the mounting plate.
Figure 3. Attaching the Monitor to the Mount
2. Secure the power and video wires to the mount using the cable ties (supplied).
NOTE: Leave service loops in the cabling to allow the mount arm to freely swing left and right and for the monitor to swivel through its range.
3. Using the 3/16-inch Allen wrench (supplied), loosen the button head bolts on the side of the mounting head. Tilt the monitor to the desired angle.
To secure the monitor in place, re-tighten the button head bolts. Refer to Figure 4.
Figure 4. Securing the Tilt Angle of the Monitor
4. To rotate the monitor between portrait and landscape views, loosen the nut on the back side of the mounting head using a 9/16-inch wrench (not
supplied). Re-tighten the nut to secure the monitor in place.
NOTE: Constant repositioning of the monitor may cause some of the bolts to loosen. Easily re-tighten the bolts using the 3/16-inch Allen wrench
(supplied).
Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates. © Copyright 2014, Pelco, Inc.
ONVIF and the ONVIF logo are trademarks of ONVIF Inc. All other product names and services are the property of their respective companies. All rights reserved.
Product specifications and availability are subject to change without notice.
Pelco, Inc. 625 W. Alluvial Ave., Fresno, CA 93711 United States
USA & Canada Tel (800) 289-9100 Fax (800) 289-9150
International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120
www.pelco.com
Warranty
For information about Pelco’s product warranty and thereto related information, refer to www.pelco.com/warranty.
REVISION HISTORY
Manual # Date Comments
C2225M 8/06 Original version.
C2225M-A 11/06 Inserted statement per UL about minimum2x4wood stud.
C2225M-B 12/06 Added hardware information for large monitors per ECO 06-17078.
C2225M-C 10/14 Added mounting details for UL compliance and updated the template.
/