Pelco DX8100 PTZ Patterns System User manual

Pelco
Brand
Pelco
Model
DX8100 PTZ Patterns System
Type
User manual

Pelco DX8100 PTZ Patterns System

Pelco DX8100 PTZ Patterns System allows you to define, store, and activate camera paths with specific movements and zoom levels. These patterns can be assigned to PTZ-enabled cameras, providing automated surveillance and monitoring capabilities. The system supports up to four unique patterns, which can be easily programmed using the on-screen controls. Patterns can be activated on-demand or set to run continuously, providing flexibility in surveillance operations.

Pelco DX8100 PTZ Patterns System

Pelco DX8100 PTZ Patterns System allows you to define, store, and activate camera paths with specific movements and zoom levels. These patterns can be assigned to PTZ-enabled cameras, providing automated surveillance and monitoring capabilities. The system supports up to four unique patterns, which can be easily programmed using the on-screen controls. Patterns can be activated on-demand or set to run continuously, providing flexibility in surveillance operations.

DX8100 PTZ PATTERNS
DX8100_PTZ_PATTERNS_PAGE_1_0F_2
Pelco and the Pelco logo are registered trademarks of Pelco.
Information subject to change without notification.
Copyright 2006, Pelco. All rights reserved.
©
World Headquart ers
3500 Pelco W ay, Clovis, Calif ornia 93612 USA
USA & Canada Tel: 866/587-2503 Fax: 800/289-9150
International Tel: 1-559/348-5504 Fax: 1-559/348-1120
www.pelco.com
DX8100 PTZ PATTERNS
A pattern is a user-defined, viewable camera path with a definite beginning and end. Patterns are made up of a sequence of standard pan,
tilt
and lens commands. Patterns are stored in the internal memory of the PTZ device, such as a Spectra
®
dome, that is connected to the DX8100
.
Depending on the type and configuration of the PTZ device, the DX8100 can address up to four unique PTZ patterns. Once defined, a pattern can
be activated with a series of on-screen commands. A pattern will run con
tinuously until it is deactivated.
Only PTZ-enabled cameras that support pattern programming through D,
P, Coaxitron, or supported third-party protocols can use this featur
e.
The PTZ controls are hidden in the extended view mode. In this case, select the standard view mode to display the PTZ controls
.
To switch between the standard and extended view mode:
PROGRAMMING A PATTERN
This section describes how to program a pattern. Certain PTZ devices, such as Pelco’
s Spectra series domes, will display an on-screen message
stating the amount of remaining memory available for pattern progr
amming.
Start Programming a Pattern
To program a pattern:
1. On the DX8100 toolbar, click .
2. Drag a camera from the Site tree onto a view panel.
3. On the DX8100 keypad, click to enter programming mode.
4. Using the PTZ keypad, select a number for the pattern (1 to 4).
5. Click .
6. Move the camera through a series of movements using the on-screen pan and tilt, zoom, and focus con
trols.
From the DX8100 menu bar, choose View > Extended View.
Stop Programming a Pattern
To stop programming a pattern:
1. On the DX8100 keypad, click .
2. Click .
ACTIVATING A PATTERN
When activated, a pattern will repeat indefinitely until it is cleared, another pattern is set, or the on-screen PTZ control is
moved.
To activate a pattern:
1. On the DX8100 keypad, click a pattern number (1 to 4) on the keypad.
2. Click .
DX8100 PTZ PATTERNS
DX8100_PTZ_PATTERNS_PAGE_2_OF_2
Pelco and the Pelco logo are registered trademarks of Pelco.
Information subject to change without notification.
Copyright 2006, Pelco. All rights reserved.
©
World Headquart ers
3500 Pelco W ay, Clovis, Calif ornia 93612 USA
USA & Canada Tel: 866/587-2503 Fax: 800/289-9150
International Tel: 1-559/348-5504 Fax: 1-559/348-1120
www.pelco.com
DX8100 PTZ PATTERNS (continued)
CLEARING A PATTERN
To clear a pattern:
1. On the DX8100 keypad, click to enter programming mod
e.
2. Select a pattern number (1 to 4) on the keypad.
3. Click .
4. Click .
5. Click again.
6. Click again to exit programming mode.
  • Page 1 1
  • Page 2 2

Pelco DX8100 PTZ Patterns System User manual

Pelco
Brand
Pelco
Model
DX8100 PTZ Patterns System
Type
User manual

Pelco DX8100 PTZ Patterns System

Pelco DX8100 PTZ Patterns System allows you to define, store, and activate camera paths with specific movements and zoom levels. These patterns can be assigned to PTZ-enabled cameras, providing automated surveillance and monitoring capabilities. The system supports up to four unique patterns, which can be easily programmed using the on-screen controls. Patterns can be activated on-demand or set to run continuously, providing flexibility in surveillance operations.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers