Marantec Dynamic vario DC Owner's manual

Brand: Marantec

Model: Dynamic vario DC

Category: Garage Door Opener

Type: Owner's manual

Dynamic vario DC

Operator system for industrial doors

Manual for installation and operation

1. Meaning of symbols  . . . . . . . . . . . . . . . . . . . . . . . . .2
2. Table of contents  . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
3. General safety advice  . . . . . . . . . . . . . . . . . . . . . . . .3
4. Product overview  . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
4.1 Dynamic vario DC supply package  . . . . . . . . . . .4
4.2 Mounting options  . . . . . . . . . . . . . . . . . . . . . . .6
4.3 Dimensions  . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
5. Preparation for mounting  . . . . . . . . . . . . . . . . . . . . .7
5.1 General notes  . . . . . . . . . . . . . . . . . . . . . . . . . .7
5.2  Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
5.3 Cabling layout  . . . . . . . . . . . . . . . . . . . . . . . . . .8
6. Installation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
6.1 Preparing the door   . . . . . . . . . . . . . . . . . . . . . .8
6.2 Mounting the shaft adapter   . . . . . . . . . . . . . . .9
6.3 Mounting the motor unit at the door   . . . . . . . .9
6.4 Mounting the torque support   . . . . . . . . . . . . .10
6.5 Connection of control elements Control x.22  .11
7. Initial operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
7.1 Overview of the control unit  . . . . . . . . . . . . . .14
7.2 Express programming  . . . . . . . . . . . . . . . . . . .14
7.3 Changing the rotational direction  . . . . . . . . . .16
7.4 Function test  . . . . . . . . . . . . . . . . . . . . . . . . . .16
8. Extended operator functions  . . . . . . . . . . . . . . . . .18
8.1 Programming structure for extended operator
functions (Example for Level 2, Menu 2)  . . . . .18
8.2 General overview of the programmable 
functions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
8.3 General overview of the programmable 
functions   . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
9.  Operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
9.1 Standard operation  . . . . . . . . . . . . . . . . . . . . .30
9.2 Emergency operation . . . . . . . . . . . . . . . . . . . .30
10. Messages  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
10.1 Overview of the display functions  . . . . . . . . . .31
10.2 Status messages   . . . . . . . . . . . . . . . . . . . . . . .31
10.3  Fault messages  . . . . . . . . . . . . . . . . . . . . . . . .32
10.4 Rectifying faults  . . . . . . . . . . . . . . . . . . . . . . . .33
11. Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
11.1 Technical data Dynamic vario DC  . . . . . . . . . . .35
11.2 EC Declaration of Conformity  . . . . . . . . . . . . .36
Caution! 
Danger of personal injury!
The following safety advice must be observed
at all times so as to avoid  personal injury!
Attention! 
Danger of material damage!
The following safety advice must be observed
at all times so as to avoid material damage!
Advice / Tip
Check
Reference
i
Advice
Motor unit identification plate
Type: ____________________________________________________
Art. No.: _________________________________________________
Product No.: ______________________________________________
2. Table of contents1. Meaning of symbols
Control unit identification plate (optional)
Type: ____________________________________________________
Art. No.: _________________________________________________
Product No.: ______________________________________________
2 Manual for installation and operation, Dynamic vario DC GB (#96400)

3. General safety advice

Please read carefully!

Target group

This operator system may only be installed, connected and put into

operation by qualified and trained professionals!

Qualified and trained specialist personnel are persons

- who have knowledge of the general and special safety regulations,

- who have knowledge of the relevant electro-technical regulations,

- with training in the use and maintenance of suitable safety equipment,

- who are sufficiently trained and supervised by qualified electricians,

- who are able to recognise the particular hazards involved when working

with electricity,

- with knowledge regarding applications of the EN 12635 standard

(installation and usage requirements).

Warranty

For an operations and safety warranty, the advice in this instruction

manual has to be observed. Disregarding these warnings may lead to

personal injury or material damage. If this advice is disregarded, the

manufacturer will not be liable for damages that might occur.

The warranty does not include batteries, rechargeable batteries, fuses and

bulbs.

To avoid installation errors and damage to the door and operator system,

it is imperative that the installation instructions are followed. The system

may only be used after thoroughly reading the respective mounting and

installation instructions.

The installation and operating instructions are to be given to the door

system user, who must keep them safe.

They contain important advice for operation, checks and maintenance.

This item is produced according to the directives and standards mentioned

in the Manufacturer's Declaration and in the Declaration of Conformity.

The product has left the factory in perfect condition with regard to safety.

Power-operated windows, doors and gates must be checked by an expert

(and this must be documented) before they are put into operation and

thereafter as required, but at least once a year.

Correct use

The operator system is intended exclusively for opening and closing

industrial doors.

The maximum torque must be observed.

Beside the advice in these instructions, please observe the general

safety and accident prevention regulations!

Our sales and supply terms and conditions are effective.

Door requirements

The operator system is suitable for use with spring balanced sectional

doors.

The door fittings must be designed to reliably prevent the door from

jumping out of the rails, particularly in the ceiling area through measures

such as axial securing mechanisms for rollers, cross-bracings for the over-

head ceiling rail brackets and rail connectors.

The bearing springs must be equipped with a spring safety device.

The suspension cables are fitted with a safety catch, which prevents any

further movement of the door in the closing direction.

the door is prevented from closing using fall protection by other structural

means that are incorporated in the suspension system, so that operation

with a suspension cable is no longer possible.

Information on installing the operator system

• Ensure that the door is in good mechanical condition.

• Ensure that the door is balanced.

• Ensure that the door opens and closes properly.

• Ensure that there is a suitable mains connection near the door.

• Remove all unnecessary components from the door (e.g. cables, chains,

brackets).

• Render any installations inoperable that will no longer be needed after

the operator system has been installed.

• Before commencing cabling works, you MUST disconnect the operator

system from the mains supply.

Adhere to the safety period of 10 seconds to guarantee that the

operator system is voltage free.

• Adhere to the local protection regulations.

• Use only fixing materials which are approved for the substrate

concerned.

• The electricity supply cables and control cables MUST be laid separately.

• Install the operator system with the door in the CLOSED position.

• Install all the impulse transmitters and control devices (e.g. remote

control buttons) within sight of the door and at a safe distance from

the moving parts of the door. A minimum installation height of 1.5 m

must be observed.

• Permanently fix the warning signs, which advise of the danger of

becoming trapped, at conspicuous locations (if applicable).

• Ensure that no part of the door extends across public footways or roads

when the installation is complete.

Information on commissioning the operator system

After initial operation, the persons responsible for operating the door

system, or their representatives must be familiarised with the use of the

system.

• Make sure that children cannot access the door control unit.

• Before moving the door, make sure that there are neither persons nor

objects in the operating range of the door.

• Test all existing emergency command devices.

• Never insert your hands into a running door or moving parts.

• Pay attention to any parts of the door system that could cause crushing

or shearing damage or accidents.

The EN 13241-1 regulations must be observed.

Manual for installation and operation, Dynamic vario DC GB (#96400) 3

4.1 Dynamic vario DC supply package

1 Dynamic vario DC motor unit (release cable 3,000 mm)

Operator system

4.1 / 1

4. Product overview

4.1 / 2

Torque support

2 Screw B4.8 x 13 (4x)

3 Wood screw 8 x 60 (2x)

4 Plastic wall plug S-10 (2x)

5 Washer 8.4 (2x)

6 Washer 5.3 (2x)

7 Fixing bracket (2x)

8 Nut with shoulder SW13 (4x)

9 Nut, self-locking, SW13 (2x)

10 Screw M8 x 16 (6x)

11 Torque support

Reference:

To ascertain the exact contents of the supply

packages for optional accessories, please refer to

the relevant instructions included.

3. General safety advice

4 Manual for installation and operation, Dynamic vario DC GB (#96400)

Please read carefully!

Information on servicing the operator system

To ensure proper operation, the following items must be checked

regularly and repaired if necessary. Before any works to the door system

are undertaken, the operator system must be disconnected from the

mains.

• Check once a month to ensure that the operator system reverses if the

door encounters an obstacle. To do so, place a 50 mm high/wide

obstacle in its path, depending on the operational direction of the door.

• Perform a check on the OPEN and CLOSE automatic cut-out setting.

• Check all movable parts of the door and operator system.

• Check the door system for signs of wear or damage.

• Check whether the door can be easily moved by hand.

• Inspect the safety devices installed every six months.

Information on cleaning the operator system

Never use water jets, high pressure cleaners, acids or bases for cleaning.

4. Product overview

Manual for installation and operation, Dynamic vario DC GB (#96400) 5

Shaft adapter set (optional)

4.1 / 3

12 Feather key 1 (1x)

(only for adapters without integrated feather key)

13 Feather key 2 (3x)

(only for adapters without integrated feather key)

14 Feather key 3 (3x)

(only for adapters without integrated feather key)

15 Shaft adapter (1x)

(Dimensions according to requirements)

16 Adjusting ring (2x)

25.4

6.35

27.55

25.4

6.4

17.8

31.75

SW 32.1

6.35

29.4

25.4

6.4

19.0

Safety devices (optional)

Remote control (optional)

4.1 / 4

Control elements (optional)

A control element is required to operate the motor unit.

17 Command 613 control element

6 Manual for installation and operation, Dynamic vario DC GB (#96400)

4. Product overview

Reference:

The relevant instructions are to be followed if

the motor unit is to be installed according to

other mounting options.

-y

Push-on assembly

4.2 / 1

Assembly with push-on shaft adapter (optional)

4.2 / 2

4.3 Dimensions

4.3 / 1

4.3 / 2

Dynamic vario DC

Space required for push-on assembly

72.5

≥ 73

≥ 348

261

420

298.5

129

119

4.2 Mounting options

Manual for installation and operation, Dynamic vario DC GB (#96400) 7

5.1 General notes

These instructions describe the push-on assembly of motor unit

models with an integrated quick release system (SE):

The pictures in these instructions are not true-to-scale.

Dimensions are always given in millimetres (mm)!

The illustrations in these instructions show the installation on the

inner right hand side, for a door with normal fittings.

For correct mounting you will need the following tools:

5.1 / 1

8 / 10 / 13 2 / 2.5 20

2.5 4 ø 9

ø 10

* Grease

Attention!

The operator system cannot be disengaged

from the outside.

A separate entrance must be available in order

to gain access to the garage in the event of a

malfunction.

The door must be properly installed and must have been checked

to ensure that it functions correctly.

• Ensure that a suitable mains connection and a mains

disconnection facility are available for your door system.

• Check to ensure that the door to be operated fulfils the

following conditions:

- The door must move easily when operated manually.

- The door must always remain stationary in any position

without external restraint.

• Determine on which side of the door system the operator

system should be mounted.

• Check to ensure that there is sufficient space to mount the

operator system.

Reference:

The relevant instructions must be observed

when mounting the operator at the door.

Reference:

When using and installing accessories, always

observe the specific instructions included with

the equipment.

5.2 Checks

Attention!

In order to guarantee correct mounting, carry

out the following checks before installing.

Supply package

• Check the package to ensure that all the parts are included.

• Check that you have all the additional components that are

necessary for your particular installation requirements.

Door system

5. Preparation for mounting

8 Manual for installation and operation, Dynamic vario DC GB (#96400)

5. Preparation for mounting

Advice:

This is just an example of a cabling layout; the

layout can vary according to the type of door

and the associated equipment.

Reference:

The relevant installation instructions must be

observed when mounting and connecting door

sensors, control elements and signalling devices.

A Dynamic vario DC motor unit

B Control unit

C Signalling device (e.g. signal light)

D Mains connection

Useable length:

- 1.1 m (230 V)

E Mains isolator switch

F Spring safety device, supplied by customer

G Door sensors for cable slack device

H Optosensors

I Photocell barrier

J Housing, connection unit

K Door sensor for wicket door

L Flat cable, motor unit - control unit

M Control

• Secure the door.

6.1 / 1

Caution!

- To prevent falls, the installation works must be

carried out from a safe standing position.

A lifting platform or scaffold can be used.

- To avoid injury, the door must be secured for

the duration of the installation works to

prevent it from being opened or closed.

6.1 Preparing the door

6. Installation

5.3 Cabling layout

5.3 / 1

Manual for installation and operation, Dynamic vario DC GB (#96400) 9

Attention!

To ensure proper operation,

- there must be a 3 mm gap between the

frame and the adjusting ring,

- the shaft adapter must fit on the spring shaft

with as little play as possible in the direction

of rotation.

6. Installation

~ 3

6.2 / 1

• Deburr the spring shaft (B) using a file.

• Push the adapting ring (A) onto the spring shaft (B).

• Tighten the screw of the adjusting ring (A).

• Grease the spring shaft.

• Push the shaft adapter (C) onto the spring shaft (B).

Only for shaft adapters without integrated feather keys:

• Insert the feather key (D) into the shaft adapter (B).

6.3 Mounting the motor unit at the door

6.3 / 1

• Place the motor unit on the shaft adapter.

6.3 / 2

• Secure the motor unit with an adjusting ring.

6.2 Mounting the shaft adapter

10 Manual for installation and operation, Dynamic vario DC GB (#96400)

6. Installation

6.4 / 1

• Fix the torque support (A) to the operator unit.

• Fix the fixing bracket (B) to the torque support (A).

• Mount the fixing bracket (B) on the wall.

Advice:

The torque support can be attached to the wall

or to the door frame.

6.4 Mounting the torque support

Mounting on the wall

6.4 / 2

• Fix the torque support (A) to the operator unit.

• Attach the first fixing bracket (B) to the torque support (A).

• Screw the second fixing bracket (C) to the first fixing

bracket (B).

• Mount the second fixing bracket (C) on the door frame.

Mounting on the door frame

Manual for installation and operation, Dynamic vario DC GB (#96400) 11

16 17

XW40B

6. Installation

Attention!

In order to avoid damaging the controls:

- The local safety regulations must be complied

with at all times.

- It is very important that mains cables are laid

separately from control cables.

- The controls voltage must be 24 V DC.

- If external voltages are applied at

terminals XW40A, XB10 or XB02, the entire

electronic system will be destroyed.

- Only potential-free contacts may be connected

to terminals 1 and 2 (XB02).

6.5 Connection of control elements

Control x.22

Caution!

Danger of electric shock:

Before any cabling works begin, it must be

ensured that the cables are disconnected from

the power supply.

During cabling works, it must be ensured that

the cables remain disconnected from the power

supply at all times (e.g. prevent reconnection).

Reference:

When installing external control elements, or

safety and signal equipment, the relevant

instructions must be observed.

6.5 / 1

Label Type / function

XB70 Connection of modular antenna –

XB02

Connection for external control

elements without system cabling and

two-wire photocell

6.5 / 3,

6.5 / 4,

Level 5

Menu 1

XB10

Connection for external control

elements with system cabling

–

XH02

Connection for programmable output

(e.g. signal light)

6.5 / 5

XM70

Connection for motor

(rotational direction)

7.3

XH75 Connection for door locking 6.5 / 6

XN70 Connection for battery backup –

XN81 Connection for mains cable 6.5 / 2

Label Type / function

XP15

Connection for

Control safety circuit

6.5 / 7

XV51 Connection for motor rotation speed –

XW40A

MS BUS,

e.g. control unit, modules

–

XW40B Connection for reference cassette –

Connection of control elements X.22

XV51 XP15 XW40A

XB02XB10

XN70

XM70

XB70

XN81

XH02

Advice:

- Before connecting a control element to the

terminals with system sockets, the correspon-

ding shorting plug must first be removed.

- The Dynamic vario DC operator system is sup-

plied with integrated controls as a standard

feature. If the controls are extended with

additional modules, the Control vario control

unit can also be connected with an MS bus.

XH75

- XN81

- X0

- F0

Terminal XN81

6.5 / 2

M07E039

Label Type / function

L Phase connection

N Neutral wire connection

PE Earth wire connection

12 Manual for installation and operation, Dynamic vario DC GB (#96400)

Advice:

- If a photocell with a standard function or door

frame function is used, it must be disconnected

from the mains before installing it and taking

it into service.

After switching on the mains voltage, the

photocell is only detected automatically by the

controls if the path of the photocell beam

remains uninterrupted for at least 5 seconds.

Otherwise the photocell must be programmed

after installation.

- Safety devices which are automatically incor-

porated in the control process after they are

connected to the control unit can only be

deactivated by removing the electrical connec-

tion and then carrying out a reset of the

control (resetting the safety devices).

Terminal XB02

-XB02

71 70

-W1

-W2

1 3

-Sb1

2 1 2

-AP27

-W1

-W2

6.5 / 3

M10E035

6. Installation

Label Type / function

1 24 V DC (max. 50 mA)

2 Impulse

3 GND

70 GND

70 + 71 Two-wire photocell

RX Receiver for the two-wire photocell

Sb1 External impulse button (if installed)

TX Transmitter for the two-wire photocell

-XH02

16 17

-HH14

M10E010

Label Type / function

15 / 16

Connection for programmable output

potential-free NC

16 Connection for command device

16 / 17

Connection for programmable output

potential-free NO

HH14 Signal light

Terminal XH02

6.5 / 5

Attention!

To avoid damage being caused to the circuit

board, the contact loading (max. 230 V / 2 A)

must be observed.

-X1

7071

- XB02

71 70

2 3

-S1

12 11

6.5 / 4

M10E040

Label Type / function

1 24 V DC (max. 50 mA)

2 Impulse

3 GND

70 GND

70 + 71 Two-wire photocell

S1 Potential-free NC contact of photocell

Terminal XB02 (external photocell)

Manual for installation and operation, Dynamic vario DC GB (#96400) 13

6. Installation

Advice:

The closing edge safety device connection is

preset in the factory for a 8.2 kΩ closing edge

safety device. If an OPTO 300 closing edge

safety device is used, a reset must be carried

out after it has been connected.

Terminal XP15 (optional)

Label Type / function

AP01 Connection unit on one side

R1 Resistor 8K2

XP01 Terminal strip, 6-pole

BP49 Contact edge CLOSED

S1 Slack rope switch

XP15

Strip, 6-pole

Control - safety circuit

- XP15

P1 b

d e f

-XP01

-W1

BN GN BK

-AP01

-S1

-R1

1 2 3 4 5 6

-BP49

6.5 / 7

M09E042

Terminal XH75 (optional)

• Connect the electric lock (A) to the junction box (B).

• Connect terminal block XH75 to the junction box (B).

Reference:

The reset of the controls is described in

Section 8.3 / Level 1 / Menu 8.

Connection example: Operation with contact edge

and slack rope switch

6.5 / 6

XH75

14 Manual for installation and operation, Dynamic vario DC GB (#96400)

7.1 / 1

Operating elements

Label Type / function

A Carousel display 10.1

OPEN button (+)

(e.g. to drive the door to

the OPEN position or to increase

parameters when programming)

CLOSE button (-)

(e.g. to drive the door to

the CLOSED position or to decrea-

se parameters when programming)

Button (P)

(e.g. to switch to

programming mode or

to save parameters)

Overview of the integrated controls Control x.22

BAD

7.2 Express programming

7.2.1 General notes on express programming

Advice:

For proper initial operation of the operator

system, the express programming procedure

must be carried out. This applies for initial

operation and after a reset.

The basic functions of the operator system are set during the

express programming procedure.

- Door OPEN position

- Door CLOSED position

- Remote control (if installed)

The programming procedure is a consecutive process. It is essential

that this procedure be carried out.

Advice:

- During the programming of the OPEN and

CLOSED door positions, the hollow shaft must

rotate around 360° at least once in order for a

reference point to be programmed.

- If the door starts to move towards the CLO-

SED position when the (+) button is pressed,

the express programming procedure must be

aborted and the rotational direction be

changed first.

The controls are programmed using the plus (+), minus (-) and

(P) buttons.

If no buttons are pressed within 120 seconds while in program-

ming mode, the controls revert to operating mode.

A corresponding message is displayed.

Reference:

The messages are explained in Section 10.

Reference:

Changing the rotational direction is described

in Section 7.3.

Starting the express programming (integrated controls)

• Carry out the express programming according to the following

procedure.

Advice:

The express programming can be exited at any

time by pressing the P button 3 times.

7.2.2 Programming buttons

7.1 Overview of the control unit

7. Initial operation

Manual for installation and operation, Dynamic vario DC GB (#96400) 15

7. Initial operation

Operating

mode

1x >2s <10s

Start express programming /

Programme the door OPEN

end position

Drive the door to the OPEN

position

Correct the OPEN door position

using (+) and (–)

1x <1s

Save the OPEN door

position /

Programme the CLOSED door

position

Drive the door to the CLOSED

position

Correct the CLOSED door

position using (+) and (–)

1x <1s

Save the CLOSED door

position /

Programme the remote

control

Press the hand transmitter

button

Release the hand transmitter

button

10.

1x <1s

Save the remote control

settings /

End the express programming

procedure

7.2.3 Express programming sequence

Legend:

LED off

LED on

LED flashes slowly

LED pulses

LED flashes quickly

Factory default setting

Not possible –

16 Manual for installation and operation, Dynamic vario DC GB (#96400)

7. Initial operation

After pressing the (+) button:

The door must open and travel to the saved

OPEN end position.

After pressing the (–) button:

The door must close and travel to the saved

CLOSED end position.

After pressing the hand transmitter button:

The operator system must move the door in

either the “OPEN” or “CLOSE” direction.

After pressing the hand transmitter button

while the operator system is running:

The operator system must stop.

When the button is pressed again,

the operator system moves in the opposite

direction.

Check:

After express programming and after making

changes to the programming menu, the

following learning runs and checks must be

carried out.

7.4 Function test

The operator system determines the maximum required driving

power during the first two runs after setting the end positions of

the door.

• Operate the operator system (with the door coupled) to drive

the door once from the CLOSED position to the OPEN position

and back to the CLOSED position without interruption.

During this learning run, the operator system determines the

maximum push and pull forces and

the reserve power required to move the door.

Test:

Attention!

- To ensure that the drive system operates

correctly, a reset must be carried out on the

operating controls after changing the

rotational direction (only required if the door

positions have already been programmed).

- Before the OPEN and CLOSED door positions

have been set, the door can be moved

electrically beyond this door position, which

could lead to the door being damaged.

Reference:

- The connection of the mains supply is

described in Section 6.5.

- The reset of the operating controls is

described in Section 8.3 / level 1 / menu 8.

- The express programming is described in

Section 7.2.3.

Caution!

Danger of electric shock:

Before cabling works commence, a check must

be carried out to ensure that the cables are at

zero voltage.

Measures must be taken to ensure that the

cables remain dead for the duration of the

works (e.g. prevent the power supply from

being switched back on).

7.3 Changing the rotational direction

7.3 / 1

XM70

• At the motor unit connection (XM70), swap the brown and the

green leads over.

• Carry out a reset of the controls.

• Carry out express programming again.

Manual for installation and operation, Dynamic vario DC GB (#96400) 17

Caution!

The automatic cut-out must be correctly pro-

grammed for the CLOSE and OPEN directions

to prevent damage to persons or property.

Automatic cut-out

Automatic cut-out, OPENING

For drive systems where the door has openings in the door wing

(diameter of opening > 50 mm):

• Apply a load of 20 kg to the middle of the lower edge of the

door whilst the door is running.

The door must stop immediately.

Automatic cut-out, CLOSING

• Place a 50 mm high obstacle on the ground.

• Drive the door towards the obstacle.

The operator system must stop and reverse when it hits

the obstacle.

Advice:

The parameter settings are still saved if the

power supply is disconnected.

Only a reset causes the driving power settings

for the OPEN and CLOSE directions to revert to

the factory settings.

7. Initial operation

Door sensors

• Activate each of the door sensors in turn.

Signalling device

• Check that the signalling device functions properly.

Check:

Check the door sensors according to the corre-

sponding operating instructions. LED 1 lights up

when a safety device is activated.

Emergency operation

• Check that the emergency operation equipment functions

properly.

Reference:

The function of the emergency operation

equipment is described in Section 9.

Photocell in the door frame area

• Activate each of the photocells in turn.

Advice:

- The photocell connected in the door frame

area must function above the position in

which it is installed. The function below the

installation position is suppressed by the

control.

- If several photocells are connected, all photo-

cells react analogue with any photocell in the

door frame area.

Photocell

• Activate each of the photocells in turn.

• Check all photocells that are connected directly before the

CLOSED door position.

18 Manual for installation and operation, Dynamic vario DC GB (#96400)

8.1 Programming structure for extended operator functions

(Example for Level 2, Menu 2)

8. Extended operator functions

End

programming

ParameterMenu

Operating

mode

(integrated

controls)

Levels

> 5 sec.

> 10 sec.

> 5 sec.

Level 3

Level 4

Menu 3 Higher value

Menu 2

Menu 1

Menu-Exit

(Level 2)

Level 2

Level 1

Levels-Exit

Level 8

Menu 8

Parameter

Lower value

Manual for installation and operation, Dynamic vario DC GB (#96400) 19

8. Extended operator functions

8.2 General overview of the programmable functions

Level Menu Factory default setting

Level 1 – Basic functions

Menu 3: Intermediate position OPEN –

Menu 4: Intermediate position CLOSE –

Menu 7: Relay output Signal light

Menu 8: RESET No reset

Level 2 – Operator settings

Menu 1: Required driving power OPEN Setting 8

Menu 2: Required driving power CLOSE Setting 8

Menu 3: Automatic cut-out OPEN Setting 8

Menu 4: Automatic cut-out CLOSE Setting 8

Level 3 – Automatic closing timer

Menu 1: Automatic closing timer Deactivated

Menu 3: Door open duration 2 seconds

Menu 4: Warning time 1 seconds

Menu 5: Start-up warning 0 seconds

Menu 7: Signal light

Door movement /

Warning: flashes

Door stoppage: off

Level 4 – Remote programming

Menu 2: Intermediate position OPEN –

Menu 3: Intermediate position CLOSE –

Menu 4: OPEN –

Menu 5: CLOSE –

Menu 8: Relay output –

Level 5 – Special function

Menu 1: Programmable impulse input Impulse

Menu 4: Relay output 180 seconds

Level 6 - Variable speed

Menu 1: Speed OPEN Setting 16

Menu 2: Soft run speed OPEN Setting 7

Menu 3: Soft run position OPEN –

Menu 4: Speed CLOSE Setting 16

Menu 5: Smart run speed CLOSE Setting 16

Menu 6: Soft run speed CLOSE Setting 7

Menu 7: Smart run position CLOSE –

Menu 8: Soft run position CLOSE –

Level 7 - Servicing and maintenance

Menu 1: Door cycle counter –

Menu 2: Maintenance counter –

Menu 3: Set the maintenance interval OFF

Menu 8: Reset servicing and maintenance No reset

Level 8 – System settings

Menu 1: Photocell Operation without photocell

Menu 2: Closing edge safety device

Door reverses a little

(OPEN/CLOSE)

Menu 3: Automatic cut-out

Door stops (OPEN)

Door reverses a little (CLOSE)

Menu 4: Operating modes Press-and-release (OPEN/CLOSE)

Menu 5: Function of the direction command transmitters Not active

Menu 6: Function of the impulse command transmitters

STOP only, then standard

sequence

Legend:

LED off

LED on

LED flashes slowly

LED pulses

LED flashes quickly

Factory default setting

Not possible –

20 Manual for installation and operation, Dynamic vario DC GB (#96400)

Reference:

If changes are made in Menus 3 and 4 in Level 1, a new performance check must be carried out (Section 7.4).

8. Extended operator functions

8.3 General overview of the programmable functions

Attention!

After a reset, all the parameters revert to the factory settings.

In order to ensure that the controls operate properly:

- all the required functions must be re-programmed,

- the remote control unit must be re-programmed,

- the drive system must be driven once to the OPEN and CLOSED door positions.

Level 1 – Basic functions

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Menu 3: Intermediate position OPEN

Set using the (+ / OPEN) and (- / CLOSE) buttons

“Intermediate position OPEN” – closing function is possible with automatic closing timer

Menu 4: Intermediate position CLOSE

Set using the (+ / OPEN) and (- / CLOSE) buttons

Menu 7: Relay output

A7 B7 C7 D7 E7 F7 G7 H7 I7 J7 K7 L7 M7 – – –

Menu 8: RESET

A8 B8 C8 D8 E8 F8 G8 – – – – – – – – –

Advice:

- Only the intermediate position that was programmed last can be used.

- If an automatic closing timer is activated (Level 3 / Menu 1), the relay output (Level 1 / Menu 7) cannot be programmed.

Caution!

Important factory default settings can be changed using the extended functions.

All the parameters must be set correctly to avoid damage to persons or property.

Page is loading ...

Marantec Dynamic vario DC Owner's manual

Brand: Marantec

Model: Dynamic vario DC

Category: Garage Door Opener

Type: Owner's manual

Download PDF

report

Marantec Dynamic vario DC Owner's manual

Marantec Dynamic vario DC Owner's manual

Related papers

Other documents