Middle Atlantic Products C5MM1-4270S Installation Instructions Manual

Brand: Middle Atlantic Products

Model: C5MM1-4270S

Type: Installation Instructions Manual

This manual is also suitable for

I-00559 Rev C

C5MM1 Series

UNIVERSAL MONITOR MOUNT

installation instructions

THANK YOU

Thank you for purchasing the C5MM1 Series Universal Mount. Please read these instructions

thoroughly before installing this product.

- Safely and easily mounts large format monitors to C5 / C5-D Credenza

- Proprietary extruded uprights for a sleek appearance

- Structural members made from heavy-duty 11 gauge steel

- Fully adjustable in height, with laser cut increments for precise adjustment

- Cable management clips included

PRODUCT FEATURES

Vertical Mounting

Brackets (Qty 2) and

Locking Clips

(Pre-Installed)

(Qty 2)

1/4”-20 Set Screws (Qty 4)

End Caps

(Qty 2)

Columns (Qty 2) and

Shoulder Bolt Plates

(Pre-Installed)

(Qty 2)

Angle Brackets (Qty 2)

MAXIMUM FLAT-PANEL WEIGHT LIMIT

TOOLS REQUIRED

• #2 Phillips Screwdriver

• 1/4” Allen Wrench

• Protective Eyewear

• Adjustable Wrench

• Torque Wrench

• 5/16” Wrench (C5-D Only)

HARDWARE/ITEMS SUPPLIED

NOTE: Additional hardware may be included.

Page 2

1/4”-20

Machine

Screws

(Qty 2)

(Tighten to

76 in-lbs)

1/4”-20

Flange Nuts

(Qty 2)

(Tighten to

76 in-lbs)

IMPORTANT SAFETY INSTRUCTIONS

WARNING: A WARNING ALERTS YOU TO A SITUATION

THAT COULD RESULT IN SERIOUS PERSONAL INJURY

OR DEATH.

IMPORTANT WARNINGS AND CAUTIONS!

WARNING! FAILURE TO READ, UNDERSTAND AND

FOLLOW THE FOLLOWING INFORMATION CAN

RESULT IN SERIOUS PERSONAL INJURY, DAMAGE TO

THE EQUIPMENT OR VOIDING OF THE WARRANTY. IT

IS THE RESPONSIBILITY OF THE INSTALLER/USER TO

ENSURE THAT THIS PRODUCT IS LOADED

ACCORDING TO SPECIFICATIONS.

WARNING! THE WEIGHT RATINGS OF THIS PRODUCT

CAN BE FOUND ON THE PRODUCT. EXCEEDING

THESE WEIGHT RATINGS CAN RESULT IN SERIOUS

INJURY OR DAMAGE TO THE EQUIPMENT. IT IS

THE RESPONSIBILITY OF THE INSTALLER/USER TO

ENSURE THE COMPONENTS INSTALLED ON THIS

MONITOR MOUNT DO NOT SURPASS THE WEIGHT

RATINGS AS AN UNSTABLE CONDITION CAN OCCUR

WHICH MAY CAUSE POSSIBLE INJURY OR DAMAGE.

CAUTION! TO AVOID AN UNSTABLE CONDITION,

MONITORS MUST BE CENTERED ON THE HORIZONTAL

MONITOR MOUNTING BRACKET.

NOTE: A NOTE is used to highlight procedures pertaining

to the installation, operation or maintenance of the product.

WARNING! ANTI-TIP FEET MUST BE INSTALLED -

FAILURE TO DO SO COULD RESULT IN PROPERTY

DAMAGE, SERIOUS PERSONAL INJURY, OR DEATH.

CAUTION! SAFETY MEASURES MUST BE PRACTICED

AT ALL TIMES DURING THE ASSEMBLY OF THIS

PRODUCT. USE PROPER SAFETY EQUIPMENT

AND TOOLS FOR THE ASSEMBLY PROCEDURE TO

PREVENT PERSONAL INJURY.

WEIGHT RATING

C5MM1-4270S (42” to 70” single monitors)

C5MM1-4255D (42” to 55” dual monitors)

C5MM1-5665D (56” to 65” dual monitors)

DETAILS

225 lbs.

160 lbs. each (320 lbs. total)

CAUTION: A CAUTION ALERTS YOU TO A SITUATION

THAT MAY RESULT IN MINOR PERSONAL INJURY OR

DAMAGE TO THE PRODUCT AND / OR PROPERTY.

Cable Management Clips

(Qty 6)

1/2”-13 Machine

Screws (Qty 2)

(Tighten to

500 in-lbs)

1/8” Allen Wrench (Qty 1)

Thread Depth Indicator

(Qty 1)

5/16” Flat Washers

(Qty 10)

Upper Mounting

Plates (Qty 2)

M5 x 12

(Qty 8)

M6 x 12

(Qty 8)

M4 x 16

(Qty 8)

(Qty 6)

M5 x 16

(Qty 6)

M5 x 20

M6 x 20

(Qty 6)

M8 x 20

(Qty 6)

1/4”-20

Machine

Screws

(Qty 4)

1/4”-20

Flange Nuts

(Qty 4)

HARDWARE/ITEMS SUPPLIED (Continued)

Page 3

2) Slide back the Top Surface of the Credenza to allow room to install the Bottom Plate as shown.

(FIGURE B)

(Qty 4)

M4 x 25

(Qty 4)

M5 x 25

M8 x 25

(Qty 6)

M8 x 30

(Qty 6)

M8 x 35

(Qty 4)

(Qty 8)

M5 x 50

M8 x 70

(Qty 4)

Horizontal Mounting Bracket

(For C5MM1-4270S -or-

C5MM1-4255D -or-

C5MM1-5665D)

(Qty 1)

Threaded Pins (Qty 2)

Universal Washers

(Qty 8)

#10 x 5/8” Pan Head Phillips

Wood Screws (Qty 16)

5/16”-18 Machine Bolts (Qty 4)

(Tighten to 135 in-lbs)

Anti-Tip Feet (Qty 2)

Level (Qty 1)

C5 3-BAY Center Bar

Supports (Qty 2)

PARTS SUPPLIED WITH 3-BAY C5 WOOD KIT:

#10-32 x 3/8” Thread

Forming Screws for C5-D

Anti-Tip Feet (Qty 8)

C5-D Center Bar

Supports (Qty 2)

SUPPLIED WITH C5-D

WOOD KIT

1/4” Large Nylon Spacers

(Qty 6)

1/2” Large Nylon Spacers

(Qty 12)

1” Nylon Spacers

(Qty 6)

1/4” Small Nylon Spacers

(Qty 6)

Nylon Spacers

(Qty 4)

1/2” Small Nylon Spacers

(Qty 6)

C5 INSTALLATION

1) 3-BAY C5 CREDENZA ONLY: Install (2) C5 3-BAY

center bar supports using (2) 1/4”-20 machine screws

and (2) 1/4”-20 flange nuts as shown. (FIGURE A)

2) Remove machine screws at rear of C5

credenza as shown using provided 1/8” allen

wrench (4 places). (FIGURE B)

3) Install anti-tip feet using existing machine screws.

Adjust feet so they touch floor. (FIGURE B, FIGURE C)

FIGURE B

Machine Screws (2)

2) Slide back the Top Surface of the Credenza to allow room to install the Bottom Plate as shown.

(FIGURE B)

(FIGURE A)

(FIGURE C)

Hardware ‘A’ Joins Plate

and Base to Top Surface

Bottom Plate Hole Pattern

(Plate ‘A’)

2a) Install the Bottom Plate and Tube Base to the

Top Surface using the supplied flathead screws

(Hardware ‘M’). (FIGURE C)

2b) Secure the Top Surface to the Credenza Frame before

continuing with the Monitor Mount installation. Please

see C5 Series Credenza Rack instructions (I-00439)

for detailed instructions.

Page 4

Machine Screws (2)

1/4”-20

FIGURE A

Flange Nuts (2)

1/4”-20

C5 3-BAY Center Bar

Supports (2)

4) Secure both angle brackets to rear of frame as

show using (1) 1/4”-20 machine screw and

(1) 1/4”-20 flange nut. (FIGURE D, FIGURE E)

5) Place C5 top surface on credenza frame, and insert

(1) 1/2”-13 machine screw through each corner bracket,

into frame and through C5 top surface as shown.

(FIGURE E)

NOTE: Hold screws in place to prevent

from falling out.

Flange Nut (1) 1/4”-20 Angle Bracket (1)

Machine Screw (1)

1/4”-20

FIGURE D

FIGURE C

(Inside) (Outside)

Machine Screws

(1 per bracket)

1/2”-13

FIGURE E

C5 Top Surface

Angle Brackets (2)

Angle Bracket (1)

Machine Screw (1)

1/4”-20

FIGURE I

C5-D INSTALLATION

1) Install anti-tip feet using (4) 10-32 x 3/8” thread

forming screws as shown (5/16” wrench required).

Adjust feet so they touch floor. (FIGURE F, FIGURE G)

2) Place (2) C5-D center bar supports on C5-D credenza,

with threaded mounting holes facing rear of

credenza. Align with slots as shown. (FIGURE H)

FIGURE F

Page 5

FIGURE H

3) Secure (2) angle brackets and (2) C5-D center

bar supports to rear of frame using 1/4”-20

machine screws. (FIGURE I, FIGURE J)

NOTE: Screws must penetrate and be tightly

secured to threaded holes in rear of

C5-D center bar supports.

4) Place C5-D top surface on credenza frame, and

insert (1) 1/2”-13 machine screw through

each corner bracket, into frame and through

C5-D top surface as shown. (FIGURE J)

NOTE: Hold screws in place to prevent

from falling out.

Machine Screws (1 per bracket) 1/2”-13

FIGURE J

C5-D Top Surface

Angle Brackets (2)

FIGURE G

Slot

C5-D Center Bar

Supports (2)

Thread Forming Screws

(4) 10-32 x 3/8”

Slot

Threaded

Mounting

Hole

C5-D Center Bar

Support

Flat Hex Head

Machine Screw (2)

5/16”-18

Machine Screws

(1 per bracket)

1/2”-13

Top Surface

Shoulder

Bolt Plate

Shoulder

Bolt

Columns (2)

Threaded

Pins (2)

Upper

Mounting

Plates (2)

4) Hang horizontal mounting bracket by

shoulder bolts on columns to determine

desired height. (FIGURE M)

NOTE: Columns are marked in

one-inch height increments.

NOTE: Teardrop shoulder bolt holes

indicate the proper orientation of the

horizontal mounting bracket.

5) If necessary, remove horizontal mounting

bracket and loosen (2) 5/16-18 flat hex head

machine screws on shoulder bolt plate to adjust

height up and down. (FIGURE N)

NOTE: Use provided level to ensure horizontal bracket is level.

6) When desired position is reached, hang horizontal

mounting bracket on shoulder bolts.

7) Tighten (2) 5/16-18 flat hex head machine screws to 15 ft-lbs.

DO NOT OVERTIGHTEN. (FIGURE N)

C5 / C5-D INSTALLATION

1) Position upper mounting plates over 1/2”-13 machine

screws on C5 / C5-D Top Surface and secure threaded

pins onto machine screws. (FIGURE K)

ighten machine screws and threaded pins to 40 ft-lbs.

Use adjustable wrench on flats of threaded pins.

2) Secure C5 / C5-D Top Surface to credenza frame.

(Refer to Assembly Instructions for C5 Series

Credenza Rack I-00439 or C5-D Series

Deep Credenza Rack I-00565)

Place columns over threaded pins (FIGURE K) and

rotate columns so that set screw holes face the rear of

C5 / C5-D credenza. Do not tighten. (FIGURE L)

Column

Set Screws

(2 per column)

1/4”-20

Page 6

FIGURE K

FIGURE L

FIGURE N

Teardrop Hole

Shoulder

Bolts

Horizontal

Mounting

Bracket

Columns

FIGURE M

TIGHTEN

TO 15 FT-LBS

FIGURE P

Selecting The Mounting Hardware To Attach Brackets To Flat Panel

1) Identify the correct diameter screw for the flat panel threaded inserts. The correct screws should

thread easily and not pull out when tension is applied.

2) To determine proper screw length, insert thread depth indicator into a

threaded insert on the flat panel.

3) Mark the thread depth indicator 1/8” above the

depth of the threaded insert. (FIGURE P)

4) Select a screw that is shorter than the 1/8” mark

made on the thread depth indicator.

CAUTION! Do not use any screw longer than the 1/8”

mark or damage to the flat panel may occur.

Small Straw

or toothpick

Depth Plus 1/8”

Mark Allowance

Small Straw

or toothpick

Depth Plus 1/8”

Allowance Mark

Thread Depth Indicator

Threaded Insert

Mark 1/8” Above Depth

C5 / C5-D INSTALLATION (Continued)

Page 7

8) Tighten set screws (4 places) using 1/8” allen wrench. (FIGURE L)

9) Secure horizontal mounting bracket to columns using (4) 5/16”-18 machine bolts.

Tighten bolts to 15 ft-lbs. DO NOT OVERTIGHTEN. (FIGURE O)

FIGURE O

Horizontal Mounting Bracket

Machine Bolts (4) 5/16”-18

TIGHTEN TO 15 FT-LBS

FIGURE Q

FIGURE R

Dimples (Face Up)

Attaching Vertical Mounting Brackets to Flat Panel

NOTE: Be sure to observe the “up” arrow on each vertical

mounting bracket to maintain the proper orientation of the

flat panel. (FIGURE R)

1) Place the flat panel face down on a soft, flat surface and

identify the number and location of screws.

2) Align the holes on each vertical mounting bracket with the

threaded inserts on the flat panel.

3) Secure each vertical mounting bracket with the

screws and hardware identified in previous

steps. Use a minimum of (2) screws per vertical

mounting bracket.

Universal Washers

Universal washers are designed to accommodate

the various M4, M5, M6 and M8 hole sizes found in

flat panels.

NOTES:

• Place flat panel on soft, flat surface while working.

• Do not place excessive pressure on back of the flat

panel.

• Universal washers must be installed between

the head of the mounting screw and the

vertical mounting bracket as shown.

(FIGURE Q)

Nylon Spacers

Nylon spacers add distance between vertical mounting

bracket and flat panel. They will fit all supplied screw sizes.

The spacers must be used only when attaching flat panels

which have:

• Recessed mount points

• Uneven mount points

• Any obstruction near the mount points

• A curved back

NOTES:

• Nylon Spacers must be stacked and oriented as shown.

• Nylon Spacers must only be installed between the vertical

mounting bracket and the flat panel.

Flat Panel

Universal Washer

Nylon Spacer

Mounting Bracket

Mount Point

Mounting Screw

Page 8

“Up” Arrow

C5 / C5-D INSTALLATION (Continued)

Hanging the Flat Panel

NOTE: This section requires two people.

Do not release your flat panel until you

are certain that the top hook of each

vertical mounting bracket is securely

seated on the upper rail of the horizontal

mounting bracket.

1) Remove locking clips from vertical mounting

bracket and rotate locking clamps down.

(FIGURE S)

2) Raise the flat panel slightly above the top

and bottom rails on the horizontal mounting

bracket. (FIGURE S)

3) Slide the flat panel down slowly, ensuring

that the top hook on the vertical mounting

bracket properly engages the horizontal

mounting bracket. (FIGURE S)

4) Check for proper height.

(Remove and adjust height as necessary)

5) Rotate locking clamps up and insert

locking pins as shown. (FIGURE T)

6) Snap end caps into the top of both columns.

(FIGURE U)

7) Snap cable management clips into columns to

secure cabling as needed. (FIGURE U)

Top

Hook

Bottom

Hook

FIGURE S

Page 9

ADETAIL

Locking Clamp

Horizontal

Mounting

Bracket

FIGURE T

Vertical Mounting

Bracket

FIGURE U

Cable

Management

Clips

C5 / C5-D INSTALLATION (Continued)

Page 10

30% Recycled Paper

WARRANTY

Middle Atlantic Products (the "Company") warrants the C5MM1 Series Universal Monitor Mount to be

free from defects in material or workmanship under normal use and conditions for the lifetime of the

product.

The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and

exclusive remedy, under this warranty shall be limited, at the Company's option, to either (a) return of

and refund of the price paid for, or (b) repair or replacement at the Company's factory of the products

purchased, or any part or parts thereof, which the Company has determined to be defective after

inspection thereof at the Company's factory.

This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by

parties other than the Company, or any modification or alteration of the products. In addition, this

warranty does not cover damage due to improper handling, assembly, installation or maintenance.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR

IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY

BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES

WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS,

BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF THE

PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER PARTY)

HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS

PAID TO THE COMPANY.

Corporate Headquarters

Corporate Voice 973-839-1011 - Fax 973-839-1976

International Voice +1 973-839-8821 - Fax +1 973-839-4982

middleatlantic.com - [email protected]

Middle Atlantic Canada

Voice 613-836-2501 - Fax 613-836-2690

middleatlantic.ca - [email protected]

Factory Distribution

USA: NJ - CA - IL Canada: ON - BC

At Middle Atlantic Products we are always listening. Your comments are welcome.

Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company.

Middle Atlantic Products C5MM1-4270S Installation Instructions Manual

Brand: Middle Atlantic Products

Model: C5MM1-4270S

Type: Installation Instructions Manual

This manual is also suitable for

Download PDF

report

Middle Atlantic Products C5MM1-4270S Installation Instructions Manual

This manual is also suitable for

Middle Atlantic Products C5MM1-4270S Installation Instructions Manual

Related papers

Other documents