Ins-30021 CARDLOCK compact
Fitting
12/09/2011
Reader covers
A black plastic or satin chrome cover comes supplied with the reader.
Technical Support
01273 811011 [email protected]
Technical help is available: Monday - Friday from 07:00 - 19:00 (GMT)
Saturday from 09:00 - 13:00 (GMT)
Due to the close proximity of the circuit board to the reader housing,
it is normal for the reader to feel warm during operation.
Suitability
Mounted on metal surface
Security-sensitive doors
Wet environments
Readers mounted together
Documentation on all Paxton products can be found on our website - http://www.paxton.co.uk/
Paxton
Wire outputs
+12V DC
0V
Lock 12V
Lock 0V
Exit input
Exit 0V
Wiring
Reset - Use one method
1. Power down the unit.
2. Press and hold the exit button.
3. Power up the unit. It will give several quick beeps.
4. Wait for a further beep and then release and press
the exit button twice more.
5. The reader will beep 3 times to conrm the reset.
OR
1. Present Enrolment card.
2. Present Door open time card twice.
3. Present Enrolment card.
4. Present Door open time card twice.
5. WAIT FOR 5 SECONDS!
Enrolment Card - must be presented when the system is rst powered on
1. Take the enrolment card from the new pack of user cards.
2. Present the enrolment card to the reader.
3. The reader will beep as the enrolment card is acknowledged.
4. All cards in the pack are now valid. The enrolment card can now be returned to it's pack.
BEEP!
BEEP!
CARDLOCK
enrolment card
1. At installation, present this
card to the reader to validate
the tokens in this pack.
2. To re-validate a user token,
present this enrolment card
to the reader followed by the
user token.
CARDLOCK
enrolment card
1. At installation, present this
card to the reader to validate
the tokens in this pack.
2. To re-validate a user token,
present this enrolment card
to the reader followed by the
user token.
1 2 3 4
1. To initialise the reader swipe this card ONCE.
The green arrow light stops flashing.
2. To re-enrol a deleted card swipe this card and then
swipe the deleted card.
Paxton Access
CARDLOCK
enrolment card
1. To initialise the reader swipe this card ONCE.
The green arrow light stops flashing.
2. To re-enrol a deleted card swipe this card and then
swipe the deleted card.
Paxton Access
CARDLOCK
enrolment card
Exit button
(push to make)
Electric release
12V DC power
supply
12V DC release current rating must be less than 1A.
0V
0V
0V
+12V
+12V
Exit
1. Power down the unit.
2. Press and hold the exit button.
3. Power up the unit. It will give several quick beeps.
4. Wait for a further beep and then release and press
the exit button twice more.
5. The reader will beep 3 times to conrm the reset.
OR
1. Present Enrolment card.
2. Present Door open time card twice.
3. Present Enrolment card.
4. Present Door open time card twice.
5. WAIT FOR 5 SECONDS!
Issuing tokens
1. On each page there are 4 'pairs' of cards - a 'User card' and a corresponding 'Shadow card' behind it.
2. Write the name of the user on the shadow card.
3. Issue the 'User card' to the user.
4. Keep the card pack containing the shadow cards in a safe place.
Fail open release card - Compact systems are fail closed as default
THIS CARD CAN ONLY BE USED WITH A FAIL OPEN LOCK.
1. Take the fail open release function card from the starter pack.
2. Present/swipe the card through the reader. The reader will beep for about a second.
3. The reader is now set to fail open mode. This allows safe operation of the door in case of re: The lock will
release when the power is cut.
4. To revert to fail closed mode, swipe the card again and the reader will beep once.
Bar a user
1. When a card is lost or stolen it is important to bar the card from your system to avoid unauthorized access.
2. To bar a card or token take it's corresponding shadow card from the card pack.
3. Present the shadow card to the reader. This will remove the lost card or token from your system.
4. A barred card can re-validated by presenting the enrolment card followed by the user card to the reader.
1 2 3 4
User Card
CARDLOCK
User Card
CARDLOCK
User Card
CARDLOCK
User Card
CARDLOCK
User Card
CARDLOCK
User Card
CARDLOCK
User Card
CARDLOCK
User Card
CARDLOCK
User Card
CARDLOCK
User Card
CARDLOCK
User Card
CARDLOCK
User Card
CARDLOCK
User Card
CARDLOCK
User Card
CARDLOCK
User Card
CARDLOCK
User Card
CARDLOCK
User Card
CARDLOCK
1 2 3 4
Swipe this card to bar:
Write name:
John Smith
John Smith
BEEP!
BEEP!
1 2 3 4
This card is used with systems where a fail open
electric release is used for the safe operation in the
event of a fire. Present the card to the reader to
drive a fail open release or a maglock. Present the
card again to revert to the fail closed operation
Paxton Access
FUNCTION CARD
fail open release
Shadow cards
User cards
Door open time (seconds)
1. Take the 'door open time' card from the starter pack.
2. Present the card to the reader. The reader will start beeping.
3. Wait for the required period you wish the door to remain open.
4. Present the card again at the end of the period to set the open time. The beeping will stop.
Silent operation
1. Take the silent operation function card from the starter pack.
2. Present the card to the reader. The reader will beep.
3. The reader is now in silent operation mode.
4. Present the card again to disable silent operation mode. The reader will beep twice.
1 3 4
BEEP!
BEEP!
2
Paxton Access
FUNCTION CARD
door open time card
The period that the door is unlocked for when a
valid token is presented is set as follows:
1. Present this card
2. Wait for the required period
3. Present this card again, the beeping will stop
BEEP!
BEEP!
BEEP!
1 2 3 4
Paxton Access
FUNCTION CARD
silent operation
Present this card to silence the beeping noises
made by the reader. Present this card again to
re-enable the beeping noises
Voltage
Switchable current
Reader head life
1 10,000
1 3
1 2
1 60 secs
11V DC 14V DC
110 mA
1A DC
- 20 °C + 55 °C
IPX7
1,000,000
34 mm 89 mm
34 mm
Specications
Operating temperature
Electrical
Environment
Min
Max
Width
Height
Depth
Current
Outdoor Use
Features
Door open time
Time zones (with additional time clock)
Silent operation
Can be used with fail OPEN locks
Can be used with fail CLOSED locks
Exit button input
Door Contact input
Alarm/bell output voltage
Waterproof
Number of Users
Access levels (Colour Zones)
Dimensions
Yes
Yes
Yes
Yes
No
No
Min
Min
Max
Max
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Paxton Proximity Vandal Proof Compact Reader User guide
-
-
-
-
-
-
-
-
-
Other documents
-
Geovision GV-AS210 User manual
-
-
Assa Abloy Traka Touch Series User manual
-
DKS 1524 User manual
-
Roger PRTxxMF Series Readers Installation guide
-
ANXELL DG-30 Operation User's Manual
-
Panasonic CF-19 series Reference guide
-
Geovision GV-GF1921/GF1922 User manual
-
GEM DG-30 User manual
-
