Schlage BE468GBAK CAM 716 User manual

Type
User manual
*24156804*
24156804
Thick Door Kit Installation Instructions
TOUCHSCREEN DEADBOLT WITH ALARM | MODEL BE469 CONNECTED TOUCHSCREEN | MODEL BE468
1
Determine the thickness of your door.
Door Thickness
1M\,” to 2Z\v
2
Choose Screws and Tailpiece Length
2a Select the screws using the chart below.
Door
Thickness
Screw Length
(Actual Size)
2Z\,” - 2Z\v
1M\,” - 2”
2b Select the tailpiece length, using the chart below.
Door
Thickness
Tailpiece Length
(Actual Size)
2Z\,” - 2Z\v
1M\,” - 2”
3
Replace the Tailpiece
3a Remove the cylinder screw from the Touchscreen.
3b Remove the cylinder from the Touchscreen.
3c Remove the cylinder cap, washer and tailpiece.
Use a paperclip or similar to press and hold down the
pin. Then unscrew the cap. The washer and tailpiece
can then easily be removed. Leave the pin in place.
Cap
Pin
Washer
Tailpiece
3d Install the new tailpiece, washer and cylinder cap.
Using the original washer and
cylinder cap, reinstall all pieces and
screw the cap into place. Do not
overtighten the cap!
3e Install the cylinder back into the Touchscreen.
Break off and discard
This kit is used to t the Touchscreen Deadbolt with Alarm and the Connected Touchscreen to doors that are between 1M\,” and 2Z\v” thick.
L If you are uncomfortable performing these steps, call a locksmith for assistance.
3f Replace the cylinder screw.
4
Replace the cable and the spacer.
4a Remove the spacer screw from the Touchscreen.
4b Rotate the spacer so the notch is aligned with the tab, then remove the
spacer from the Touchscreen.
4c Remove the existing cable from the Touchscreen and replace it with the
longer cable.
NOTE: If you are installing the lock on a door with a 1Z\x” (38
mm) hole, stop here; do not reinstall the spacer. Do replace the
spacer screw.
4d Feed the cable through the spacer, as shown.
4e Press the cable into the groove.
4f Replace the spacer as shown and rotate back into place.
4g Replace the spacer screw.
You will know the
spacer is in the right
place when the hole
in the spacer lines up
with the hole in the
Touchscreen.
5
Install the lock.
Install the lock as detailed in the Installation Guide, using the longer screws you
selected in step 2a.
NEED HELP?
Please call customer support before returning the product to the store.
Toll-Free Calling From:
U.S.A.: (888) 805-9837
Canada: (800) 997-4734
Mexico: 018005067866
Visit our web site for videos, FAQs and more: answers.schlage.com
4.25
5.500
FRONT
Additional Notes: Revision History Revision Description:
B > Updated artwork
1. None A B C D E F
032181 042894
Material
White Paper
Edited By Approved By EC Number Release Date
D. Myers P. Bockelman 042894 12-12-13
Notes
1. printed two sides
2. printed black
3. tolerance ± .13
4. printed in country may vary
5. drawings not to scale
6. folded so barcode shows on front
Title
BE469 Thick Door Kit IS
Creation Date
01-03-13
Number
24156804
Revision
B
Created By
M. Sasso
Activity
3899 Hancock Expwy
Security, CO 80911
© Allegion 2013Software: InDesign CS6
17.000
11.000
BEGINNING SHEET
FOLDED SHEET
Front Front Back Back
Page 1
Page 2
Page 3 Page 4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Schlage BE468GBAK CAM 716 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI