Chicco Lullaby SE Owner's manual

Lullaby

Lullaby LX

Lullaby SE

Owner's Manual

Manual del propietario

IS0088.3ES

Read all instructions BEFORE

assembly and USE of product.

KEEP INSTRUCTIONS FOR

FUTURE USE.

Lea todas las instrucciones ANTES

de armar y USAR este producto.

GUARDE LAS INSTRUCCIONES

PARA USO FUTURO.

2

Failure to follow these warnings and the instructions could result in

serious injury or death

WARNING

• PLEASE READ THESE INSTRUCTIONS

CAREFULLY TO ENSURE THE SAFETY

OF YOUR CHILD.

• ALWAYS PROVIDE THE

SUPERVISION NECESSARY FOR

THE CONTINUED SAFETY OF YOUR

CHILD. WHEN USED FOR PLAYING,

NEVER LEAVE CHILD UNATTENDED.

• Playard MUST be fully assembled

with all top rails and center ﬂoor hub

locked into position prior to use or

attaching bassinet. Make sure latches

are secure.

• DO NOT place child in playard unless

all top rails and center ﬂoor hub are

securely locked into position and

ﬂoor pad is in proper place. Infant

may roll into space between pad and

loose mesh sides causing suffocation.

• Stop using this product when your

child reaches 35 inches (89 cm) in

height, weighs more than 30lbs

(14kg), or is able to climb out.

• DO NOT use the bassinet when a

child is in the playard.

• FALL HAZARD - To help prevent

falls, do not use bassinet when infant

begins to push up on hands and

knees or weighs over 15lbs (6.8kg),

whichever comes rst.

• Child can become entrapped and die

when improvised netting or covers are

placed on top of product. Never add

such items to conne child in product.

• DO NOT use bassinet on a bed, oor

or other surfaces.

• The bassinet is designed for use ONLY

with this Chicco Lullaby Magic Playard.

• Stop using the changing table when

your child reaches 25lbs (11.4 kg).

• Never use this product if there are

any loose or missing fasteners, loose

joints, broken parts, or torn mesh/

fabric. Check before assembly and

periodically during use. Contact

Chicco for replacement parts

and instruction if needed. Never

substitute parts.

• Although Chicco DOES NOT

RECOMMEND renishing this

product, if you choose to renish,

use a nontoxic nish specied for

children's products.

SUFFOCATION HAZARDS - Infants

can suffocate:

• In gaps between extra padding and

product side, and

• On soft bedding.

• Use ONLY the mattress provided

by Chicco. Never add a pillow,

comforter, or another mattress for

padding.

3

Failure to follow these warnings and the instructions could result in

serious injury or death

WARNING

• If a sheet is used with the pad, use

only a tted playard sheet specically

designed to t snug with at least 2”

(5cm) under all sides of the mattress.

The sheet must allow proper use of

the mattress retention straps.

• DO NOT leave child in product with

any side lowered. Be sure all sides

are raised and locked in position

whenever child is in product.

• NEVER use plastic shipping bags as

mattress covers. Do not use plastic

lm as mattress cover unless sold and

intended for that purpose. They can

cause suffocation.

• DO NOT use a water mattress with

this product.

STRANGULATION HAZARDS:

• NEVER use additional mattresses,

padding, sheets, or other objects that

will permit your child to climb out,

fall and/or be injured. If you choose

to ignore this warning, then remove

additional padding, large toy, and

other objects that could serve as steps

for climbing out when your child is

able to pull to a standing position.

• STOP using Bassinet when child

can roll over or push up on hands

and knees or reaches 15lbs (6.8 kg),

whichever comes rst.

• Strangulation Hazard: Child can lift

changing table and get neck trapped

between changing table and playard

frame.

• Never leave changing table in place

when child is in the playard.

• Strings can cause strangulation! DO

NOT place items with a string around

child’s neck (hood strings, pacier

cords,etc.) or attach strings to toys.

• DO NOT suspend strings into the

bassinet or playard.

• DO NOT place the playard near a

window where cords from blinds or

drapes can strangle a child.

• Never leave the bassinet in place

when child is in playard.

OTHER HAZARDS:

• Keep bassinet and playard away from

stoves, heaters, replaces and other

hazards which can cause injury to

your child.

• To reduce the risk of SIDS (Sudden

Infant Death Syndrome), pediatricians

recommend healthy infants be

placed on their back to sleep unless

otherwise advised by a physician.

• DO NOT place more than one child in

bassinet or playard.

• DO NOT move or fold bassinet or

playard with child in it - child could be

injured.

Page is loading ...

7

Setting Up the Playard

Instalación del corralito

WARNING

Before use remove and dispose of

any plastic bags and keep them

out of reach of children to avoid

the danger of suffocation.

Failure to follow these warnings

and instructions could result in

serious injury or death. Make sure

top rails and center ﬂoor hub are

locked and secure before use. This

product requires adult assembly.

Keep ngers clear of top corners

during setup.

ADVERTENCIA

Antes del uso, saque y deseche las

bolsas de plástico y póngalas lejos

del alcance de los niños para evitar

el peligro de asxia. No observar

estas advertencias e instrucciones

podría resultar en lesiones serias

o la muerte. Asegúrese de que los

rieles superiores y la base central

del piso estén trabados y jos antes

de usar el corralito. Este producto

debe ser ensamblado por un adulto.

Mantenga los dedos alejados de

las esquinas superiores durante el

montaje.

Page is loading ...

13

Setting Up the Playard

Instalación del corralito

6. Locate 4 Mattress Pad strap holes

on the ﬂoor of the playard. Thread

the 4 hook and loop straps/D-rings

through the ﬂoor of the playard as

shown.

6. Ubique los 4 oricios para las

correas de la colchoneta en el piso

del corralito. Pase las 4 correas

sujetadoras de velcro o de arandelas

en D hasta el piso del corralito como

muestra la imagen.

6

14

Setting Up the Playard

Instalación del corralito

7. Turn the playard on its side and pull

the straps completely through the

ﬂoor of the playard. Thread the strap

around the frame tube as shown. Pull

tight through D-ring and attach hook

and loop together to secure. Pull up

on mattress pad once the straps are

installed to be sure the mattress is

secure.

7. Ponga el corralito de lado y tire de

las correas completamente hasta que

pasen a través del piso del corralito.

Pase la correa alrededor del tubo de la

estructura como muestra la imagen.

Ajuste fuertemente la arandela en D y

las correas sujetadoras de velcro para

que queden jas. Tire de la colchoneta

una vez que las correas estén

instaladas para asegurarse de que

esté rme.

7

a.

b.

c.

d.

Page is loading ...

16

Assembling Bassinet

Armado de la cuna

10A & B. Fasten four end snaps (10A)

and pull eight toggles through loops

on the sides (10B).

10A & B. Sujete los quatro broches

del extremo (10A) y tire los ocho

cazonetes a través de los nudos de los

costados (10B).

10A

9

10B

9. Slide metal bars into tubing sleeves

inside bassinet and connect metal

bars together.

9. Deslice las barras de metal dentro

de las fundas de los tubos y dentro de

la cuna. Conecte las barras entre sí.

17

Assembling Bassinet

Armado de la cuna

11. Place the mattress in the bottom

of the bassinet. Ensure all straps are

folded under the mattress.

11. Coloque el colchón en el fondo

de la cuna. Asegúrese de que todas

las correas estén plegadas debajo del

colchón.

11

WARNING

Do not place Bassinet on unit if a

child is in the playard. Make sure

playard is fully assembled.

ADVERTENCIA

No ponga la cuna en la unidad si el

niño está en el corralito. Asegúrese de

que el corralito esté completamente

armado.

18

WARNING

FALL HAZARD - To prevent

death or serious injury, always

keep child within arm's reach.

• Never leave child unattended.

• Stop using the changing table

when your child reaches 25 lb

(11.4 kg).

• Do not use on the oor, bed,

counter or other surfaces.

• Do not use changing table as a

sleeping or play area.

• Always remove the changing

table when your child is in the

playard.

• Do not use changing unit if it is

damaged or broken.

ADVERTENCIA

PELIGRO DE CAÍDA - Para

prevenir la muerte o lesiones

graves, siempre mantenga niño

alcance de la mano.

• Jamás deje a su hijo solo.

• Deje de utilizar el cambiador

cuando el niño pese 25 libras

(11.4 kg).

• No usarlo en el piso, la cama, el

tablero o otro supercie.

• No use el mudador como

colchón para jugar o para hacer

dormir a su bebé.

• Siempre retire el mudador

cuando su bebé permanezca en

el corralito.

• No use el mudador si falta o

está rota alguna pieza.

Changing Table Warnings

Advertencias para el cambiador

Page is loading ...

20

Assembling Changing Table

Instalación de la mesa para cambiar al bebé

13

13. Attach both metal end pieces to

poles, making sure metal spring

button pushes completely through the

holes. Do the same on the opposite

end of the changing table.

13. Conecte los soportes de metal a

los postes, asegurándose de que

el botón del resorte de metal pasa

completamente por el agujero. Haga

lo mismo con el otro extremo de la

mesa.

Page is loading ...

22

Assembling Changing Table

Instalación de la mesa para cambiar al bebé

15A. Attach the two buckles on the

end panel of the changing table to

the buckles on the long side of the

playard. Repeat on other side of

changing table.

15A. Engancha las dos hebillas del

panel del extremo de la mesa para

cambiar al bebè al lado largo del

corralito. Repita el procedimiento del

otro lado de la mesa para cambiar al

bebè.

15A

23

16. Zip the zipper on the side of the

changing table to the end panel of

the playard. NOTE: All 4 buckles and

the zipper must be securely fastened

when changing table is in use.

Unbuckle the four buckles on the ends

of the changing table. Keep the zipper

zipped. Turn the changing table over

to the outside of the playard.

16. Cierre el cierre en el costado de

la mesa para cambiar al bebè hasta

el panel del extremo del corralito.

NOTA: Las cuatro hebillas y el cierre

deben estar debidamente asegurados

cuando usa la mesa para cambiar al

bebè.

Desabroche las cuatro hebillas de los

extremos del cambiador. Mantenga el

cierre cerrado. Dé vuelta el cambiador

hacia afuera de la cuna corral.

16

Assembling Changing Table

Instalación de la mesa para cambiar al bebé

24

WARNING

Recommended use from birth to 5

months. The toy gym is intended for

visual stimulation and is not intended

to be grasped by the child. Always

attach the provided fasteners (strings,

straps, clamps, etc.) tightly to toy

gym and playard according to the

instructions. Check frequently for

loose or damaged parts. Possible

entanglement or strangulation injury.

DO NOT add additional strings or

straps to toy gym or playard. Remove

toy when baby begins to push up on

hands and knees.

ADVERTENCIA

Uso recomendado: del nacimiento

hasta los 5 meses. El gimnasio está

diseñado como estímulo visual y no

para que el niño lo manipule. Fije

siempre los sujetadores provistos

(cuerdas, correas, abrazaderas, etc.)

rmemente al gimnasio y corralito de

acuerdo con las instrucciones. Revise

frecuentemente para vericar que no

haya piezas ojas o dañadas. Posible

lesión por enredo o estrangulamiento.

NO agregue cuerdas o correas

adicionales al corralito o gimnasio.

Saque el juguete cuando el bebé

comience a incorporarse apoyándose

en las manos y las rodillas.

Assembling the Toy Gym Arch

Cómo armar el arco del gimnasio para bebés

17. Insert all 4 Toy Gym legs into

center hub until they "click" into

locking position .

17. Inserte las cuatro patas del

gimnasio para bebés en el cubo

central hasta que se encaje en la

posición de bloqueo y se oiga clic.

17

Page is loading ...

26

Assembling the Toy Gym Arch

Cómo armar el arco del gimnasio para bebés

19. Use the hook and loop straps at

the end of each toy gym leg. Pass the

strap through the D-ring under the

mattress pad, and fasten.

19. Utilice las correas sujetadoras

en las el extremo de cada pata del

gimnasio. Pase la correa a través del el

anillo D debajo del colchón para jar

el gimnasio y ajuste.

19

Page is loading ...

30

With the switch in the MELODY ( ) or SOUND ( ) position you can activate

the following.

VOLUME: To increase the sound, press the ( ) side of the button. To decrease

the sound, press the ( ) side of the button.

VIBRATION: Push the VIBRATION ( ) button once to activate vibration cycle

and it will automatically turn off in 10 minutes. To immediately stop the vibration

cycle, press the VIBRATION ( ) button again. Note: When the LIGHT ( )

button is pushed in the middle of the vibration cycle the light will turn off when

the vibration cycle ends.

LIGHT: Push the LIGHT ( ) button once to activate light cycle and it will

automatically turn off in 10 minutes. To immediately stop the light cycle, press

the LIGHT ( ) button again. Note: When the VIBRATON ( ) button is pushed in

the middle of the light cycle the vibration will turn off when the light cycle ends.

MUSIC/FAST FORWARD: Push the MUSIC/FAST FORWARD ( / ) button once,

it will move to the next melody/sound, play for the 10 minute cycle and stop. If you

press and hold down the MUSIC/FAST FORWARD ( / ) button for 2 seconds, it

will play the current melody/sound continuously for 5 minutes and stop.

23A. The Lullaby NiteLite has (3) modes:

SOUND: The SOUND ( ) position plays

nature sounds. The SOUND ( )

selection will cycle through 3 different

sounds for 10 minutes and go into

standby/sleep mode. MELODY: The

MELODY ( ) position (2) plays soothing

music. The MELODY ( )selection will cycle

through 5 different songs for 10 minutes

and go into standby/sleep mode. OFF: The

(OFF) position will turn OFF all electronics.

To prolong life of batteries, make sure the

power switch is in the OFF position when

not in use.

23

Operate NiteLite Electronics (Select models)

Para utilizar los componentes electrónicos NiteLite

(modelos selectos)

Page is loading ...

32

24A. To operate the remote control: Slide

the power button on the Nitelite to the

Melody or Sound position. Point the

remote control directly toward the

NiteLite. The remote must be within 10

feet of the electronics unit to send a signal.

Make sure that there are no obstacles

between the remote control and the

remote sensor on the unit. After 45

minutes of no activity with the remote,

the electronic corner and remote enter a

"Sleep" mode to save battery life. To wake

the remote/corner out of sleep mode, a

function on the corner must be pressed or

turn corner off then on.

24A. Para utilizar el control remoto: Deslice el botón de encendido desde

NiteLite hasta la posición de Melodía o Sonido. Apunte el control remoto

directamente hacia NiteLite. El control remoto debe estar dentro de un radio de

10 pies de la unidad electrónica para enviar una señal. Asegúrese de que no haya

obstáculos entre el control remoto y el sensor remoto de la unidad.

Después de 45 minutos de inactividad del control remoto, la unidad electrónica

de la esquina y el control remoto pasan a modo “Suspendido” para ahorrar

batería. Para sacar el control remoto/la unidad de la esquina del modo

Suspendido, se debe presionar una función en la unidad de la esquina, o bien

apagar la unidad de la esquina y luego encenderla nuevamente.

24A

Operating the Remote Control (Select models)

Operación del control remoto (modelos selectos)

33

Operating the Remote Control (Select models)

Operación del control remoto (modelos selectos)

VIBRATION: Push the VIBRATION ( ) button once to activate vibration cycle

and it will automatically turn off in 10 minutes. To immediately stop the vibration

cycle, press the VIBRATION ( ) button again. Note: When the LIGHT ( )

button is pushed in the middle of the vibration cycle the light will turn off when

the vibration cycle ends.

LIGHT: Push the LIGHT ( ) button once to activate light cycle and it will

automatically turn off in 10 minutes. To immediately stop the light cycle, press

the LIGHT ( ) button again. Note: When the VIBRATON ( ) button is pushed in

the middle of the light cycle the vibration will turn off when the light cycle ends.

MUSIC/FAST FORWARD: Push the MUSIC/FAST FORWARD ( / ) button

once, it will move to the next melody/sound, play for the 10 minute cycle and

stop. If you press and hold down the MUSIC/FAST FORWARD ( / ) button for

2 seconds, it will play the current melody/sound continuously for 5 minutes and

stop.

OFF: To stop all of the functions and put the NiteLite into SLEEP mode press

the OFF button. The OFF button does not turn off the power on the NiteLite. To

prolong life of batteries, make sure to slide the power switch on the NiteLite to

the OFF position.

24B. With the switch in the MELODY

( ) or SOUND ( ) position you

can activate the following:

VOLUME: To increase the sound,

press the ( ) side of the button. To

decrease the sound, press the ( )

side of the button.

24B

Page is loading ...

36

26

26. Top rails cannot be unlocked rst.

Remove bassinet, gym, pad, and

NiteLite. Pull up on the center ﬂoor

hub release strap and lift the center

hub up as far as possible.

26. Los rieles superiores no pueden

destrabarse primero. Quite el moisés,

el gimnasio, la almohadilla y NiteLite.

Tire de la correa de liberación de la

base central del piso y levante la base

central lo máximo que sea posible.

Packing Up the Playard

Empaquetado del corralito de juguetes

27. Lift and squeeze center of top rail

to release lock. Push down on top rail

while continuing to squeeze. Top rail

cannot be pushed in until the lock

joint is lifted. If top rail will not unlock,

pull up on center ﬂoor hub release

strap to make sure ALL ﬂoor rails are

unlocked. Center ﬂoor hub must be

even with top rails.

27. Levante y presione el centro del riel

superior para liberar la traba. Empuje

hacia abajo ei riel superior sin dejar de

presionar el centro. El riel superior no

puede presionarse hasta que la junta

de encastre se haya elevado. Si el riel

superior no se destraba, tire de la

correa de liberación de la base central

del piso para asegurarse de que

TODOS los rieles estén destrabados.

La base central del piso debe estar

nivelada con los rieles superiores.

27

Page is loading ...

38

Packing Up the Playard

Empaquetado del corralito de juguetes

30. Keep instructions for future use.

30. Guarde las istrucciones par uso

futuro.

30

39

Trouble Shooting Guide

TOP RAILS FAIL TO LOCK INTO AN UPRIGHT POSITION :

Before top rails can be locked, the center ﬂoor hub must be pulled up as high as the 4

corners. If needed pull up on the center ﬂoor hub release strap. If necessary, pull the

release strap up with one hand and lock rails one at a time. Call Chicco Customer

Service (p. 54).

THE FLOOR JOINTS DO NOT FLATTEN:

Turn playard upside down and make sure joints are free from foreign objects.

TOP RAILS DO NOT UNLOCK TO FOLD:

Lift top rail ﬁrst, then squeeze to release. Before top rails can be unlocked, the center ﬂoor

hub must be pulled up. If needed pull up on the center ﬂoor hub release strap as high as

the 4 corners.

FLOOR JOINTS DO NOT UNLOCK:

Pull up on the center ﬂoor hub release strap to unlock ﬂoor joints.

FOLDED PLAYARD DOES NOT FIT INTO MATTRESS PAD AND IT IS DIFFICULT TO

ATTACH HOOK AND LOOP STRAPS:

Pull up on the center ﬂoor hub release strap and gather playard legs towards the center to

make the playard more compact. If necessary, shift playard lower on pad or turn slightly

and try again.

BASSINET DOES NOT FIT ONTO PLAYARD:

Playard top rails must be fully upright and locked. Playard ﬂoor must be ﬂat.

LULLABY NITELITE ELECTRONICS DOES NOT FIT ONTO CORNER CAPS:

Do not force electronics over corner caps. Try another cap. NiteLite will ﬁt onto any of the

corner caps.

Page is loading ...

Chicco Lullaby SE Owner's manual

This manual is also suitable for

Chicco Lullaby SE Owner's manual

in other languages

Related papers

Other documents