Intelbras IVP 3011 TETO User manual

Brand: Intelbras

Model: IVP 3011 TETO

Type: User manual

User’s Manual

IVP 3011 Teto (Ceiling)

English

IVP 3011 Teto (Ceiling)

Infrared passive sensor

Congratulations, you just have purchased a product with Intelbras

quality and safety.

IVP 3011 Teto sensor has a 360° view angle and its detection is done

by passive infrared rays, reducing the risk of false shots.

Caution and safety

» LGPD - General Law for the Protection of Personal Data: Intelbras does not access,

transfer, capture, or perform any other type of treatment of personal data from

this product.

» Follow all instructions of the manual for product mounting and installation.

» This movement sensor is to be used in indoor environments.

» Do not touch on surface of the infrared sensor (PIR). If necessary, use a soft cloth

with alcohol to clean.

» The sensor must be installed where a possible intruder could be easily detected,

that is, where a person does transversal movements in relation to the sensor de-

tection beams when entering into the environment. The suggested installation

height is 4 m.

» Do not put objects in front of the sensor that may block scanning.

» Avoid installing the sensor near to the following interference sources: reexive

surface, areas subject to sudden temperature changes (such as air conditioners

and heaters, fans, refrigerators and ovens).

» Avoid installing in places where sunlight goes directly onto the sensor.

» Install the sensor in a stable and shake-free place.

» For your safety, perform test of product and systems at least once a week. It is

necessary due to changes in environmental conditions, electronic failures or power

outage and aws. Take all the required precautions to keep your property safe

and protected.

Top view scan

3 m

0 m

2 m

1 m

0 m

3 m 3 m1 m

1 m

2 m 2 m

Upper view

Detection range (side view)

Sensor

Vista lateral

4 m

Sensor

Vista lateral

Terminal block

» Tamper: Anti-tamper key

» (-) GND: negative source

» (+) 12 V: Positive source

» Alarm: sensor output

+12 V GND Alarm Alarm Tamper

654321

Summary

1. Technical specications 6

2. Features 6

3. Producto 7

4. Installation 8

5. Operation 10

6. Test 11

Term of Warranty 12

1. Technical specications

Operating voltage 12 Vdc

Operating current ≤18 mA

Operating temperature -10°C to 60 °C

Detection method PIR

Detection distance Diameter 7 m

Alarm outlet NC - NO (500 mA 100 Vdc)

Recommended installation height 4 m

Startup time 60s

Detection angle 360°

Anti-tamper key (TAMPER) NC

Size 25 × Ø86 mm

LED ON - OFF

Detection pulse (P. COUNT) 1P - 2P - 3P

Note:

the infrared detection range can be inuenced by the environment.

2. Features

» Ceiling installation.

» Digital signal processing (DSP).

» Automatic temperature compensation.

» Anti-tamper protection (tamper key).

» Adjustable infrared sensitiveness (PIR).

» Optional NC and NO relay output.

3. Producto

11 11

1. Front

2. Lens

3. Base

4. Bolt xation holes

5. Cable passage

6. Jumper P.COUNT (pulse counter)

7. Jumper Relay

8. PIR sensor

9. Jumper LED

10. LED Indicator

11. Terminal Block (connectors)

12. Tamper key (anti-violation)

4. Installation

» Execute the installation in an area free of obstacles that may hinder the visual

eld of the sensor.

» The PIR (P-COUNT) sensitivity adjustment must be done according to each envi-

ronment.

To attach the sensor in the ceiling, follow the procedure:

1. Open the front cover pulling it upward (gures 1A and 1B);

2. Pass the cable through the cable passage orice in the back cover (Fig. 2);

3. Pass the cable through the orice and connect it to the terminal block (item 1.3.

Terminal block);

4. Attach the sensor in the ceiling, passing the screw through the holes in the back

cover (Fig. 3).

Note:

drilling screw M3 × 25.

Back cover Front Jumper

Figure - 1A Figure - 1B

Cable entry Cable

Back cover

Figure 2

Back cover

Screw

Figure 3

5. Operation

LED jumper is used for LED indication without interfering with the detector. Jumper

in ON position (pin 1 & 2) light on. Jumper in OFF position (pin 2 & 3) light off.

Factory standard: LED on.

The P.COUNT jumper controls the pulse count for alarm activation. With the jumper

in the 1P position, the sensor provides maximum sensitivity (one pulse, pins 1 & 2)

With the jumper in the 2P position, the sensor provides intermediary sensitiveness

(two pulses, pins 2 & 3), and in this position, the sensor provides proper detection

for environments with high incidence of EMI and RFI interferences. Factory stan-

dard: 2P.

Note: if the P.Count jumper is open, the sensor sensitivity will be 2P.

The RELAY jumper controls the relay contact status. With jumper in the NC position,

the contact is normally closed. With jumper in the NO position, the contact is

normally open. Factory standard: NC

P-COUNT

Relé

LED On/Off

Jumper P.COUNT

Position Condition

1 P 1 Pulse – maximum sensitivity

2 P 2 Pulse - medium sensitivity

3P 3 Pulse - minimum sensitivity

Jumper relay

Position Condition

NC Normally closed

NO Normally open

Jumper LED

Position Condition

Closed LED on

Open LED off

6. Test

When energized, the LED lights on, indicating that the self-test has been activated

by the sensor.

It performs the walk-through test, with transversal movements to sensor detection,

by observing the LED indication.

Note: while a movement could be detected, the LED remains on and will indicate

open or closed.

Walk through the area where you want to protect to check if it is within the area

covered by the sensor. The sensor sensitivity and its installation position will dene

the coverage area.

Sensor

4 m

Term of Warranty

It is expressed that this contractual warranty is granted according to the following

conditions:

Customer name:

Customer’s signature:

Tax Invoice No.

Date of Purchase:

Model: Serial No.:

Retailer

1. All parts, pieces and components of this product are warranted against any man-

ufacturing defects, which may arise within a period of 1 (one) year - being 90

(ninety) days of legal warranty and 9 (nine) months subject to contractual warran-

ty - from the date when the Customer purchased the product, according to the

product purchase tax invoice, which is an integral part of this Term throughout

the Brazilian territory. This contractual warranty expressly includes the product ex-

changes in case of manufacturing defect. If no manufacturing defect is conrmed,

but there is a failure due to improper use, the Customer shall bear any of these

incurred expenses.

2. The product must be installed according to the Product Manual and/or Installation

Guide. If your product requires to be installed and congured by a skilled techni-

cian, your should seek for a reliable and skilled professional, but the costs of such

services are not included in the product price.

3. Once the defect is conrmed, the Customer shall contact immediately the nearest

Authorized Service listed in the report provided by the manufacturer, they are the

only professionals authorized to check and remedy the defect within the warranty

term provided herein. It it is not observed, the warranty is void, characterized as

product infringement.

4. Eventually, if the Customer requests service at home, he/she may contact the near-

est Authorized Service to ask for fee quotation of a technical visit. If it is necessary

to withdraw the product to be repaired, the incurred expenses such as transpor-

tation and insurance costs, including taking and return after repaired, are under

responsibility of the customer.

5. The warranty will be entirely voided if any of the following cases occur: a) if the

defect is not due to manufacturing, but caused by the Customer or by third parties

foreign to the manufacturer; b) if the product damages are caused by accident,

disasters, agents of nature (lightning, ooding, landslide, etc.), humidity, network

voltage, over-voltage caused by accident or excessive network voltage uctua-

tions), installation/use in disagreement with the user’s manual or due to natural

wear of parts, pieces and components; c) if the product had suffered any effects of

chemical, electromagnetic, electric or animal (insects, etc.) nature; d) if the product

serial number was altered or erased; and e) if the appliance is awed.

6. This warranty does not cover data loss, therefore, in case of a product, it is advis-

able to the Customer to regularly make secure backup of the product data.

7. Intelbras is not liable for the installation of this product, as well as eventual at-

tempts of fraud and/or sabotage in their products. Keep software and applications

up to date, and if necessary, the required network protections against intrusions

(hackers). The equipment is warranted against defects under normal conditions of

use, and it is important to bear in mind that, because it is an electronic equipment,

it is not protected from attempts of frauds or misleading actions that may interfere

in its correct operation,

8. After its useful life, the product must be delivered to an Intelbras authorized sup-

port service or perform environmentally proper nal disposal in order to avoid

environmental or health impacts. If you prefer, useless cells and batteries as well

as other Intelbras branded electronic appliances may be disposed at any Green

Eletron collection points (electro-electronic residues management company to

which we are associated). If you have any questions about the reverse logistics

process, contact us by phone (48) 2106-0006 or 0800 704 2767 (from Monday to

Friday at 8 AM to 8 PM, and on Saturday at 8 AM to 6 PM) or via e-mail suporte@

intelbras.com.br.

Also under these supplementary Term of Warranty, Intelbras S/A reserves the right

to alter general, technical or aesthetics features without prior notice.

All images in this manual are for illustrative purposes only.

01.23

Made in China

Customer Support: (48) 2106 0006

Forum: forum.intelbras.com.br

Support via chat: chat.intelbras.com.br

Support via e-mail: suporte@intelbras.com.br

Customer Service: 0800 7042767

Where to buy? Who installs it? 0800 7245115

Imported to Brazil by: Intelbras S/A – Indústria de Telecomunicação Eletrônica Brasileira

Rodovia SC 281, km 4,5 – Sertão do Maruim – São José/SC – 88122-001

CNPJ 82.901.000/0014-41 – www.intelbras.com.br

Intelbras IVP 3011 TETO User manual

Intelbras IVP 3011 TETO User manual

Intelbras IVP 3011 TETO User manual

Related papers

Other documents