Genesis LG2 WP-6004 Installation Handbook

Brand: Genesis

Model: LG2 WP-6004

Type: Installation Handbook

This manual is also suitable for

LG2 WP-3020

Genesis LG2 WP-604 is a wireless PIR detector featuring a 60-meter detection range and 4-meter width. It uses Black Mirror Technology to provide excellent detection with minimal false alarms. The device is IP66-rated for water resistance and has a detection angle of 90 degrees. It is powered by two 1.5-volt C cells or an optional 12-volt DC power supply. The LG2 WP-6004 can be programmed to various settings, including sensitivity, pulse count, and AND/OR gating. It also features anti-masking, shock, and rear tamper protection.

Luminite Genesis product range

Wireless PIR detectors

G1 Wireless PIR’s 30m x 20m LGWP3020

G1 Wireless PIR’s 15m x 20m LGWP1520

G1 Wireless PIR’s 40m x 4.5m LGWP4004

G1 Wireless PIR’s 12m Horizontal curtain LGWP12HC

G1 Wireless PIR’s 12m Vertical curtain LGWP12VC

G2 Wireless PIR’s 30m x 20m LG2WP3020

G2 Wireless PIR’s 60m x 4m LG2WP6004

Wireless Accessories

IP Masthead/Repeater LGIP MT434

Masthead/Repeater LGMT434

Masthead Relay Unit LGMRU4x4

Relay Expansion Module LGREM4x4

Walk Test Instrument LGWT434

16 way relay unit LGRU16

Relay module LGRM8

16 way DM interface unit LGDM16

16 way relay unit with end of line resistor LGRU16ELR 3 versions

Relay module with end of line resistor LGRM8ELR 3 versions

Optional antenna AE434

Transmitter module LGTX434

Hard wired PIR detectors

G1 Wired PIR’s 30m x 20m LGHW3020

G1 Wired PIR 15m x 20m LGHW1520

G1 Wired PIR 40m x 4.5m LGHW4004

G1 Wired PIR 12m horizontal curtain LGHW12HC

G1 Wired PIR 12m vertical curtain LGHW12VC

G2 Wired PIR’s 30m x 20m LG2HW3020

G2 Wired PIR’s 60m x 4m LG2HW6004

LUMINITE ELECTRONICS LTD, 2a BELLEVUE ROAD, FRIERN BARNET, LONDON, N11 3ER

Tel: 0044 (0) 208 368 7887 Fax: 0044 (0) 208 368 3952

Web: www.luminite.co.uk email: [email protected]

Wireless

PIR Detector

Installation

Handbook

2a BELLEVUE ROAD, FRIERN BARNET, LONDON, N11 3ER

Tel: 0044 (0) 208 368 7887 Fax: 0044 (0) 208 368 3952

Type: LG2 WP-3020 & WP-6004

V2 Issue 1

PRE-INSTALLATION NOTES

Unpacking.

On receipt, inspect the package and contents for signs of damage. If damage

has occurred, advise the carrier and/or suppliers immediately. Inspect the con-

tents to confirm that all items are present and undamaged. If any items are

missing or damaged, contact the supplier immediately. It is advisable that the

original carton is retained as this forms the safest transport container in the

event that a unit has to be returned for any reason.

Servicing.

This unit should not require general servicing. Any repair work should only be

undertaken by qualified service personnel.

Moisture.

Do not expose the internal electronics of this unit to moisture i.e. take care dur-

ing installation or when changing batteries not to allow rain or damp into the

product. When the product is sealed it is water resistant to IP66.

Take great care of the mirror surface. Do not scratch it or allow dust or dirt to

settle on it.

Box Contents.

1 x GENESIS wireless G2 series PIR detector

1 x Rear tamper ring magnet

3 x no 8 wall plugs

3 x no 8 2” screws

1 x no 6 1/2” screw

1 x no 6 wall plug

1 x spare battery selector jumper

LG2WP-3020 & 6004 Wireless PIR Detector Specification.

Mirror type 30 metre x 20 metre or 60 metre x 4 metre.

Detection / Anti Tamper / Anti Cloaking / Shock.

Temp comp Temperature sensor compensates for extreme conditions

Batteries 2 x 1.5 volt C cells (supplied)

or 1 x 3.6 volt lithium. (not supplied)

Power supply 12 volts DC (optional instead of batteries)

IP rating 66

Enclosure High impact ABS with EPDM 1mm thick window

Colour Silver

Temperature -10 +70

LG2 WP-3020 & WP-6004 Wireless PIR Detector Installation Handbook Page 2.

LG2 WP-3020 & WP-6004 Wireless PIR Detector Installation Handbook Page 15.

Detection Patterns.

There are two

mirror versions to

choose from but the

mirrors are not inter-

changeable.

Model LGWP3020

Model LGWP6004

Detection range will vary according to the air temperature and surrounding envi-

ronment.

For example: large areas of white concrete in very hot weather will reduce the

sensitivity as will air temperatures of 37 degrees. If these situations occur and

are present every day then it may be necessary to increase the sensitivity of the

detector by following the instructions on page 11.

LG2 WP-3020 & WP-6004 Wireless PIR Detector Installation Handbook Page 14.

Testing & Commissioning.

Adjust the mirror to the desired direction of detection .

Plug on the battery jumper and observe the momentary HI message on the

display.

Program the setting as required. Pages 10 & 11.

It is recommended to set AND/OR to 1 and Pulse Count to at least 2.

Fit the front cover to prevent air flow around the sensor which will cause an

alarm. DO NOT PUSH THE WHITE WINDOW.

It is not necessary to secure the screw but be aware that the tamper will remain

during testing until the screw is fitted.

Using the LGWT434 Walk Test Instrument walk within the detection area,

stopping and waiting for about five seconds each time detection occurs.

The instrument will display D each time detection occurs.

Lens type will display as Type 6 for the 6004 or Type 7 for the 3020.

See the operating instructions for the walk tester for more information.

Adjust the mirror as described on page 9 and re-test until optimum coverage is

achieved.

Once you are happy that the detector is operating to your requirements, screw

the cover screw up from the bottom being careful not to cross thread it.

NB: Because the cover has a liquid tight gasket seal there will be an air

pressure build up inside the product which will gradually normalise. The side

effect of this will be to cause the sides around the gasket to lift slightly. Using

the palms of your hands, gently push the sides in and towards the wall which will

close up the gap. Be careful not to push the white window as damage will

occur.

INDEX

page

mechanical or electrical, is strictly prohibited without the express written permission of

Luminite Electronics Ltd.

Luminite Electronics Ltd acknowledge all registered trademarks.

Luminite Electronics Ltd reserve the right to make changes to this handbook and to its

LG2 WP-3020 & WP-6004 Wireless PIR Detector Installation Handbook Page 3.

Introduction. 4 & 5

Installation. 6

Mounting height and positioning.

Minimising false alarms.

Batteries 8

Mirror adjustments. 9

Programming. 10, 11

Wireless transmission code settings 11

PIR functions. 12

Testing and commissioning. 14

Detection patterns. 15

Types of tamper. 13

Introduction

The LG2WP3020 & LG2WP6004 wireless Passive Infra Red Detectors (PIR)

have been designed to meet the newest and most demanding requirements of

the CCTV market. These new, stylish detectors are available in two different

detection patterns and use superior Black Mirror Technology to provide excellent

detection with minimal false alarms.

The two ranges are:

30 metres out x 20 metres across or

60 metres out x 4 metres across.

ENCLOSURE.

LG2 detectors have a modern styling which disguises the product’s true function

and helps them to blend in with modern architecturally designed buildings. The

front window is made of pigmented HDPE which hides the mirror and the main

body of the enclosure is ABS with a high quality paint finish. Both parts are UV

stabilized and the weather proof rating is IP65.

BLACK MIRROR TECHNOLOGY.

These new PIR’s use mirror technology instead of Fresnel lenses. The large

mirror provides significantly more optical gain which allows a thick EPDM front

filtered window to be used without the need to increase sensitivity.

White light from car headlights can cause false alarms, so it is important to filter

out this interference. Most PIR detectors use pigmented windows or Fresnel

lenses and sometimes an extra silicon filter to reduce white light, but this has the

effect of also reducing the infrared energy and consequently detection range.

The Black Mirror acts as a selective optical filter for body heat infrared with mini-

mal loss while filtering out unwanted white light by as much as 14000 LUX.

The combination of high optical gain and white light filtering means that the elec-

tronic sensitivity is much lower and therefore the risk of false alarms from electri-

cal interference and component noise is greatly reduced.

The other problem of running amplifiers at extremely high gain is that they reach

saturation which obscures any signature that the micro controller would use to

accurately determine the validity of a detection.

The Luminite LG2 amplifier runs at a relatively low level and with the combina-

tion of the adaptive focal length optically sharp edges of each mirror segment

together with the sophisticated detection algorithm has the result is accurate de-

tection at various speeds and distances.

LG2 WP-3020 & WP-6004 Wireless PIR Detector Installation Handbook Page 4.

LG2 WP-3020 & WP-6004 Wireless PIR Detector Installation Handbook Page 13.

Types of tamper:

Front cover micro switch.

Activated when the cover screw is removed.

Rear tamper Hall effect and magnet.

The magnet is fixed to the wall and when the product is removed the magnet is

left behind.

Shock sensor.

Piezo sensor on mother board detects physical attack of the product.

Anti masking.

Active IR and LDR sense when the front window is obscured. These sensors

always face the same direction as the mirror.

LG2 WP-3020 & WP-6004 Wireless PIR Detector Installation Handbook Page 12.

PIR FUNCTIONS.

Pulse count.

Counts the number of pulses caused when a person walks across the detector’s

field of view. The greater the number, the more the person has to move to

cause an alarm. Pulse count 1 is very sensitive while pulse count 4 is quite

insensitive. Experiment with the setting to optimise the results so that

persons are detected in good time but not so sensitive that the detector may be

prone to false alarm from incidental movement from trees, shrubs, loose

materials etc.

Sensitivity.

The normal setting is 0. Low sensitivity is sometimes needed to reduce the

detection distance.

Higher sensitivity increases distance but also increases the risk of false

activation from environmental conditions.

AND / OR.

The Genesis 2 PIR detector uses a Quad in line pyro sensor which

acts like two separate sensors side by side.

The AND / OR mode can select whether both sensors must detect movement

together or whether only one or the other is required.

AND gating is the best form of filtering out nuisance alarms from loose

materials, foliage and reflections.

OR gating is more sensitive and may be selected when fast moving objects are

to be detected.

Power saving.

Busy sites such as school playgrounds, car park entrances etc can cause an

unnecessarily large number of alarm transmissions.

Although these alarms may be ignored during the day time it is still wasteful of

battery power and therefore in these circumstances it is recommended that the

Power saving mode be selected.

There are four types of power saving which may be selected to suit.

1. An alarm can only be sent after 3 minutes of inactivity

2. An alarm can only be sent after 10 minutes of inactivity

3. An alarm can only be sent after 30 minutes of inactivity

4. The same as 3 but with an accumulative timer which can extend the 30

minutes if the site remains very busy.

In addition the sleep timer does not initiate after the first alarm but instead

after a build up of activity.

LG2 WP-3020 & WP-6004 Wireless PIR Detector Installation Handbook Page 5.

ADAPTIVE FOCAL LENGTH.

The mirrors have adaptive focal length which regulates the image size no mat-

ter where it is in the field of view. This enables accurate detection of a target at

various speeds and distances and also makes it easier to filter out small animal

movements.

AND OR.

The Quad in line pyro sensor splits each detection zone into two which are then

labelled A and B. The G2 detector can be configured to go into alarm with either

(A AND B) or (A OR B). AND detection is the best way to minimise false alarms

as it filters out spurious movements from loose materials and foliage.

SHOCK and CLOAK.

The G2 PIR also contains a shock sensor to detect physical attack and IR trans-

mission anti-masking. On the hard wired version, these alerts activate the anti

masking relay but only momentarily.

BATTERIES.

Two 1.5 volt alkaline C cell batteries MN1400 LR14 are provided but the product

can also be powered from one 3.6 volt Lithium C cell battery instead.

Recommended EVE type ER26500.

Lithium batteries are recommended for cold climates where temperatures drop

well below freezing.

Alkaline batteries are water based and can freeze. After freezing they will be

irreparably damaged.

EXTERNAL POWER.

The G2 detector may alternatively be powered from an external supply (not sup-

plied) which must be 12 volts DC and at least 100m/a.

This product cannot be powered from both battery and external power source at

the same time.

LG2 WP-3020 & WP-6004 Wireless PIR Detector Installation Handbook Page 6.

Installation:

First, the front cover must be removed by unscrewing the bottom screw and

lifting the cover just past the top of the gasket. Push the whole cover

upwards so that it slides out off the retaining claws. (See diagram supplied in

the carton).

To fix the product to the wall and connect to the terminals, it is easier to remove

the mirror assembly (recommended).

Mirror removal procedure.

Detach the mirror assembly by

removing the white knurled nut

and the R clip.

Pull out the bottom spindle

followed by the top threaded

spindle. Unplug the 6 way

Plug from the mother board and

carefully place the assembly to

one side ensuring that it does not

get wet or contaminated. The

mirror must remain perfectly clean

and scratch free.

Using the drill template pro-

vided, drill and plug the holes us-

ing the supplied wall plugs.

Screw the rear tamper magnet in

the centre using the No4 screw

and yellow plug.

Place the product over the

magnet so that it resides in the

rear recess and then screw the

product in place using the three

No8 screws provided.

Re-fit the black hole bungs

provided to maintain the weather

rating.

6 way plug

20mm Cable entry

BAT1 BAT2

External power

input

Front cover screw insert

Screw holes

& bungs

Screw hole

& bung

Front cover claw sockets

Cable glands

6 way socket

Knurled nut

LG2 WP-3020 & WP-6004 Wireless PIR Detector Installation Handbook Page 11.

The LED display will automatically turn off after 10 minutes.

MODE OPTIONS: SETTINGS:

SI SITE 1 to 32

SU SUB NET 1 to 8

Un UNIT NUMBER 1 to 64

PL PULSE COUNTING 1 to 4

SE SENSITIVITY -5..0..+5 -5 Lowest, 0 Normal, +5 Highest

An AND/OR GATING 0=Applied 1=Not applied

PS POWER SAVING 0-OFF, 1 to 4 ON (Four modes)

WIRELESS TRANSMISSION CODE SETTINGS:

Site code.

These codes are used to separate one site from another.

There are 32 codes to choose from and any number can be used as long as it is

different from other nearby sites that are using Genesis products. The

LGWT434 Walk Test Instrument can be used to search for nearby sites and dis-

play the site codes used.

Sub net.

A division of the site code and usually only used where repeaters are required.

See LGMT434 operating instructions for more information.

Unit code. Each detector must have an individual unit number. Set the first de-

tector as UNIT1 and the second as UNIT2 etc. Do not duplicate numbers or

leave gaps.

LG2 WP-3020 & WP-6004 Wireless PIR Detector Installation Handbook Page 10.

PROGRAMMING:

The new version 2 model now has an

LED display and push buttons to set

the mode of operation.

This makes changing settings much

easier as the buttons and display are

easily located on the top of the mirror.

Button functions.

SELECT UP

M MEMORISE DOWN

Power On,

When the power is turned on, the display shows momentarily.

How to set standard functions.

Step 1. Enter the settings mode press M until the display shows

Step 2. Scroll through mode the options with this button EG:

When the desired mode is reached, wait a moment and then the display will

flash the setting. EG: = pulse count 1.

To change a setting, select the mode and wait for the setting to flash.

Scroll up or down to the desired number.

Step 3. Press and hold the M button to store the new number.

The display shows followed by

Now let go of the button and the new setting is now stored.

EXAMPLE: M

To change more than one setting at a time, follow steps 1 and 2 and after

changing the setting press to select the next mode. Press the M button when all

changes have been made.

NB: The display will automatically turn off after 10 minutes if M is not pressed.

TRAN1

LG2 WP-3020 & WP-6004 Wireless PIR Detector Installation Handbook Page 7.

IMPORTANT:

Make sure that the rear tamper magnet has been fitted first using the tem-

plate before fixing the product in place.

Mounting height

2.5m

Mounting height

The correct height for the PIR is 2.5 metres above

the ground, however it can be mounted up to 4 me-

tres but the mirror must be angled down. See

“mirror adjustments”.

Mounting height and positioning.

Minimising false alarms.

Make sure that nothing can move or flutter in front of the detector and avoid fac-

ing reflective surfaces. The fixing of the detector must be solid and not sway.

Avoid situations where the detector can overshoot the detection area.

The Genesis 2 detector uses a patented Black Mirror which filters out unwanted

sunlight however it is still good practice to consider the position carefully to mini-

mise the possibility of reflections.

20mm Cable entry

6 way socket

LG2 WP-3020 & WP-6004 Wireless PIR Detector Installation Handbook Page 8.

Batteries:

Genesis 2 is supplied with two alkaline 1.5 volt C cells. (MN1400 LR14)

These cells are fitted in BAT1 and BAT2 positions.

To turn the product on, the battery selector jumper must be fitted to the 2x1.5V

position.

If the product is to be used in very cold climates then it is recommended to use

one 3.6 volt lithium C cell (not supplied) instead.

(Recommended EVE ER26500)

This battery must be fitted to the BAT1 position.

In this instance, the two alkaline batteries must be removed and the battery

selector jumper fitted to the 1x3.6V (BAT1) position.

NB: The battery selector jumper is used to turn the detector on as well as select

between one 3.6 volt battery or two 1.5 volt batteries.

The jumper must be removed if the product is to be powered from an external

source.

External power supply:

This product can be powered from an external 12 volt DC supply instead of bat-

teries. Remove the battery selector jumper and the alkaline batteries.

NB: If batteries are left in the product for many years, they may leak and dam-

age the circuit board.

Cable entry is via the IP66 rubber grommets at the rear of the detector, or the

cable entrance at the bottom of the detector which is a knockout for a 20mm

cable gland.

2 x 1.5V

1 x 3.6V

(BAT1)

2 x 1.5V

1 x 3.6V

(BAT1)

2 x 1.5V

1 x 3.6V

(BAT1)

OFF

2 x 1.5V

1 x 3.6V

(BAT1)

OFF

LG2 WP-3020 & WP-6004 Wireless PIR Detector Installation Handbook Page 9.

Mirror adjustments:

If the mirror assembly was removed, re-fit it now.

Horizontal Left / Right adjustment is achieved by slackening the knurled white

thumb screw and rotating the mirror assembly click by click in 10 degree steps to

the required position. The degrees –90 0 +90 are shown in the picture.

Fine adjustment from –5 to +5 degrees is achieved by rotating the Fine Adjust

screw either clockwise or anti-clockwise.

Vertical Up / Down adjustment is achieved by adjusting the white plastic screw

as shown.

Aim the mirror in the direction you wish to protect and tighten the horizontal

course adjust screw.

It is not normally required that the mirror be tilted up or down and it should be

left in the neutral 0 deg position.

Horizontal Fine Adjust.

Vertical Adjust

Mirror tilt.

+ 5 deg

0 deg

-5 deg

-10 deg

-15 deg

Top view

Horizontal

Coarse Adjust

–90 +90 degrees

Genesis LG2 WP-6004 Installation Handbook

Brand: Genesis

Model: LG2 WP-6004

Type: Installation Handbook

This manual is also suitable for

LG2 WP-3020

Download PDF

report

Genesis LG2 WP-6004 Installation Handbook

This manual is also suitable for

Genesis LG2 WP-6004 Installation Handbook

Related papers

Other documents