Emac NJPMAL5071 Installation guide

Type
Installation guide

This manual is also suitable for

R03.001_11/01/2011
TECHNICAL FILE
Novojunta® Pro Mobile
Supported trafc loads
Novojunta Pro® Móvil is able to support semi-heavy loads.
It allows trafc category G according to ACI Standard, American Concrete Institute, ACI 302.1R-89 y
ACI 360.1R-92, for vehicles with net weight >= a 30 kN y <= a 160 kN, distributed on both axis.
Trucks with rigid or pneumatic wheels classied as FL1, 2, 3 y 4 with net weight up to 60 kN and load
up to 40 kN, with a total load per axis of 90 kN, according to standard ACI 302.1R-89 y ACI 360R-92.
It allows static overload less than 5 t/m
2
and the passage of vehicles over pneumatic wheels less than
2,5 t/axis, according to the classication of medium loads over pavements NTE-RSC.
Vehicles for transport up to 38 kN per axis, in models with simple axis. It can achieve 60 kN per axis
with slow trafc.
Technical Features
Materials
Page 2 of 4
Alloy: 6063 (AA y ASTM)
L-3441 (UNE 38-301-89)
Fire resistance: M0 (UNE 23-727-90)
Abrasion resistance: Very good
Lightfastness: Excellent
Appearance and color: EN 12373-1
Aluminum
Novojunta Pro® Mobile is a prole made by extrusion of aluminum. These proles have been anodized,
improving mainly by this proccess their corrosion and mechanical resistance and their appearance.
The anodized applied, has the quality seal “Qualanod” which guarantees the quality of the process and
the resulting proles. This seal regulates several tests: appearance and color, thickness measurements,
sealing and impregnation control, abrasion resistance, lightfastness, acetic saline chamber and nitric
acid immersion.
Aluminum is a material with excellent chemical, physical and mechanical properties. It is lightweight,
tough, ductile, malleable and highly durable.
This classication has been obtained from Standards ACI 302.1R-89 (Guide for concrete oors and
construction slabs, referring to the magnitude of the load they can support) and ACI 360.1R-92 (Design
of the different degrees of oors, which describe the six common types of oors for construction
referred to the actions induced by trucks and transport vehicles) and the classication of trucks
(depending on the net weight, dimensions and load which transport).
R03.001_11/01/2011
TECHNICAL FILE
Novojunta® Pro Mobile
1. Clean the surfaces where the Novojunta Pro® Mobile will be installed. Take the sealant membrane
and remove the lm which covers the area with adhesive.
2. Place the sealant membrane on the sides of the joint and ensure it gets a perfect adhesion.
3. Align correctly the sealant membrane and keep a curve shape enough to allow its free movement.
4. Place the prole over the sealant membrane previously installed.
5. Mechanize the holes for the anchoring screws. Use the holes on the anchoring wing of the prole
to guide you.
6. Insert the anchoring screws and x them rmly using a hammer or similar.
7. Install the tiles on the wall or the oor both sides of the joint.
8. Remove the protective lm and the plastic separators of the surface of Novojunta Pro® Mobile
and let dry.
Installation
Page 3 of 4
Novojunta Pro® Mobile is delivered assembled and it is easy to install. It incorporates plastic separators
on the face side to speed the correct installation up.
If it is needed to install a prole for a joint between oorings with different thickness, it is possible by
combining the different pieces available. Novojunta Pro® Mobile combines performance and versatility
and can be installed in multiple situations.
It can be installed with or without sealant membrane. It is an optional element but always
recommendable. The installation is in the same way without the steps referring to the installation of
the sealant membrane.
Installation with sealant membrane:
1 2 3
4
5
6
7
TECHNICAL FILE
R03.001_11/01/2011
You can nd out more information about the technical features of the Emac®’s products by downloading
its Technical Files in www.emac.es.
If you have any query, please contact our Technical Department in [email protected].
Technical Information
Emac Complementos S.L. (Spain) info@emac.es // Emac America L.L.C. (FL,USA) [email protected] // Emac Italia S.R.L. (Italy) [email protected]
www.emac.es
The data provided are for information only and have been obtained by our supplier or Emac®.
Does not constitute legal guarantee in terms of properties and / or functionality of the application of material
Novojunta® Pro Mobile
Cleaning and maintenance
IndoorsOutdoors Wall tiling Flooring Recyclable
Page 4 of 4
The cleaning must be done periodically with a soft cloth. If you use a neutral liquid cleaner, you must
rinse the prole with cold water and dry to remove excess moisture. If dirtiness persists, clean the
prole with a solution with clean water and detergent or neutral soap 5%, brushing with a cloth that
has no particles that could scratch the nish.
Steel wool, abrasive cleaners, souring products as well as strong acids (hydrochloric and
perchloric),strong bases (caustic soda or ammonia) or carbonated solutions are not recommended.
Citric acid is neither recommended because disolves the protective layer of the surface of aluminium.
Waxes, petrolatum, lanolin or similar substances are not appropriate. Solvents containing haloalkanes
(hydrouoroether and chlorinated solvents) and curing accelerators containing chlorides should not be
used (use special accelerators free of chlorides)
  • Page 1 1
  • Page 2 2
  • Page 3 3

Emac NJPMAL5071 Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages