Grandeur 849540 Installation guide

Type
Installation guide
For assistance call 800-522-7336 Monday through Friday 7am to 5 pm Mountain Time
PKDMY 10162017
FOR NON-PREPPED DOORS.
1/4”
1/4”
1/4”
Tall Plate
Mounting
Holes
Bottom
Grip
Mounting
Hole
2 3/4”
Match the height (from the
floor) of the bottom grip
mounting hole position for
the active handleset. Place
the flat side of the plastic
template against the door,
with the bottom hole B at
this height. Mark the other
two B holes, and drill a
1/4” hole through the door
at all three locations.
Intall screw
extenders
into
exterior
plate.
Tighten
securely.
Screw
Extenders
(part #8)
Place
exterior
plate
on the
outside
of the
door.
Dummy Door Inside
Dummy
Door
Outside
Insert
bottom grip
mounting
screw.
Tighten
screw
securely.
Install the
mounting
screw
cover.
9
11
Bottom Grip
Mounting Screw
(part #10)
Dummy Door Outside
Insert dummy cylinder
into exterior plate.
Mark the mounting
screw hole.
Remove the dummy
cylinder and drill a 1/8”
hole 3/4” deep into
the door.
Mount the dummy cylinder
with the 1” wood screw
(part #2) and tighten
securely.
Dummy Door Outside
Dummy Cylinder
(part #3)
Carefully place
the cylinder cover
(part #1) onto the
dummy cylinder
(part #3).
Use a miniature
screwdriver
to bend the
retaining tabs.
Dummy Door Outside
Cylinder Cover
(part #1)
Attach
tall plate
with included
screws.
Tighten screws
securely.
Dummy Door Inside
Install the latch strike on
the dummy door.
Latch and deadbolt
strikes included
with active handleset.
Dummy
Door
Dummy Door Inside Dummy Door Inside
Install the
deadbolt strike
on the dummy
door.
Latch and deadbolt
strike included
with active
handleset.
Dummy
Door
3/4
Note: Handlesets fit doors 1-3/4” to 2” thick.
Dummy Handleset
TALL PLATE
with
ONE-PIECE EXTERIOR PLATE
Grandeur
Door Hardware
Installation Instructions
9
11
5
6
4
3
2
1
8
7
10
1.
Cylinder Faceplate
2.
1″ Wood Mounting Screw
3.
Dummy Cylinder
4.
One-Piece Exterior Plate
5.
6.
2″ Machine Screws (2) for 1-3/4″ thick
doors. 2-1/4″ Machine Screws (2) for
2″ thick doors.
7.
Tall Plate
8.
Screw Extenders
9.
10.
11.
Screw Cover Adapter
Handleset Grip
2-1/2″ Bottom Grip Mounting Screw for
1-3/4″ thick doors. 2-3/4″ for 2″ thick doors.
Mounting Screw Cover
Part
Number
Part
Description
Exploded Drawing Single Dummy Handleset–
Tall Plate with One-Piece Exterior Plate
B
B
B
Place the at side of the
plastic template against
the door.
Position the bottom grip
mounting hole B at the same
height as the active handleset.
Use position of top two small
holes (B) to mark and drill 1/4” holes
through the door.
1.
2.
3.
For assistance call 800-522-7336 Monday through Friday 7am to 5 pm Mountain Time
PKDMY 10162017
  • Page 1 1
  • Page 2 2

Grandeur 849540 Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI