Everbilt ESE60W-HD User guide

Everbilt
Brand
Everbilt
Model
ESE60W-HD
Type
User guide

Everbilt ESE60W-HD is a 1/2 HP Sewage pump with 115V, 60Hz, 1-phase PSC motor. With max flow rate at 52 GPM and max head at 18', this pump is perfect for moving large amounts of water. It comes equipped with a cast-iron body, stainless steel shaft, and a thermal overload switch to protect the motor from damage. The pump is also CSA certified and backed by a 1-year warranty.

Everbilt ESE60W-HD is a 1/2 HP Sewage pump with 115V, 60Hz, 1-phase PSC motor. With max flow rate at 52 GPM and max head at 18', this pump is perfect for moving large amounts of water. It comes equipped with a cast-iron body, stainless steel shaft, and a thermal overload switch to protect the motor from damage. The pump is also CSA certified and backed by a 1-year warranty.

TROUBLESHOOTING - ESE60W SEWAGE PUMP
Problem Cause/Solution
The pump does not run The line circuit breaker is off, or the fuse is blown or loose.
and makes a humming
The water level in the basin has not reached turn-on level as indicated in the Installation
sound.
Requirements drawing.
The pump cord plug is not making contact in the receptacle.
The float is stuck. It should operate freely in the basin.
If a gate valve is used, make sure it is open
If all of the above are OK, then the motor could be malfunctioning.
The pump runs but does Check if the valve is installed backwards. The arrow on the valve should point in the direction of flow.
not deliver water.
Check for bloclage in the check valve.
The discharge shut-off valve (if used) may be closed.
The impeller or volute openings are fully or partially clogged. Remove the pump and clean.
The pump is air-locked. Start and stop several times by plugging and unplugging the cord. Check for a
clogged vent hole in the pump case or discharge pipe.
The inlet holes in the pump base are clogged. Remove the pump and clean the openings.
The vertical pumping distance is too high. Reduce the distance or change the discharge fittings of the pump.
The pump runs and The float is stuck in the up position. Be sure the float operates freely in the basin.
pumps out sump,
The float switch is defective. Replace the float switch.
The pump runs but only The pump is air-locked. Start and stop several times by plugging in and unplugging the cord.
delivers a small amount Check for a clogged vent hole in the pump case.
of water.
The vertical pumping distance is too high. Reduce the distance or change the discharge fitting of the pump.
Inlet holes in pump base are clogged. Remove pump and clean the strainer and openings.
The impeller or volute openings are fully or partially clogged. Remove the pump and clean.
The fuse blows or circuit The pump impeller is partially clogged, causing the motor to run slowly and overload. Remove the pump
breaker trips when the and clean.
starts
Pump must be on a separate circuit.
The motor stator may be defective.
There may be more than the pump on the circuit overloading and tripping the circuit board.
The fuse size or circuit breaker may be too small (must be 15 A).
The impeller or volute openings are fully or partially clogged. Remove the pump and clean.
The motor runs for a The inlet holes in the pump base are clogged. Remove the pump and clean the openings.
short time and then
The pump impeller is partially clogged, causing the motor to run slowly and overload. Remove the pump
stops.
and clean.
The motor stator may be defective.
The impeller or volute openings are fully or partially clogged. Remove the pump and clean. Also clean
the strainer if one is installed.
The pump continually There is no check valve in the long discharge pipe allowing liquid to drain back into the sump.
cycles Install a check valve in the discharge line.
The check valve is leaking. Inspect the check valve for correct operation.
The basin is too small for inflow. Install a larger basin.
  • Page 1 1

Everbilt ESE60W-HD User guide

Everbilt
Brand
Everbilt
Model
ESE60W-HD
Type
User guide

Everbilt ESE60W-HD is a 1/2 HP Sewage pump with 115V, 60Hz, 1-phase PSC motor. With max flow rate at 52 GPM and max head at 18', this pump is perfect for moving large amounts of water. It comes equipped with a cast-iron body, stainless steel shaft, and a thermal overload switch to protect the motor from damage. The pump is also CSA certified and backed by a 1-year warranty.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents