WAREHOUSE-LIGHTING COM WL-MAWP WareLight Mini Adjustable Wall Pack Installation guide

Brand
WAREHOUSE-LIGHTING COM
Model
WL-MAWP WareLight Mini Adjustable Wall Pack
Category
Motorcycle Accessories
Type
Installation guide

This manual is also suitable for

WAREHOUSE-LIGHTING COM WL-MAWP WareLight Mini Adjustable Wall Pack is a wall-mounted LED luminaire designed for outdoor use. It features adjustable light output angles, allowing you to direct the light where you need it most. The luminaire is designed to operate in ambient temperatures ranging from -30°c to 40°c and is suitable for use in a variety of outdoor applications, including architectural lighting, security lighting, and area lighting. The luminaire is easy to install and comes with all necessary hardware. It is also backed by a 5-year warranty.

WAREHOUSE-LIGHTING COM WL-MAWP WareLight Mini Adjustable Wall Pack is a wall-mounted LED luminaire designed for outdoor use. It features adjustable light output angles, allowing you to direct the light where you need it most. The luminaire is designed to operate in ambient temperatures ranging from -30°c to 40°c and is suitable for use in a variety of outdoor applications, including architectural lighting, security lighting, and area lighting. The luminaire is easy to install and comes with all necessary hardware. It is also backed by a 5-year warranty.

FULL CUTOFF WALL PACK
Installation Guide
WARNING
PLEASE READ ALL INSTRUCTIONS BEFORE ATTEMPTING INSTALLATION
— To prevent personal injury or product damage only licensed electricians should install.
— To avoid electric shock or component damage disconnect power before attempting installation or servicing.
— This product must be installed in accordance with the national electric code (NEC) and all applicable federal, state and local electric codes and safety standards.
— Disconnect product and allow cooling prior to servicing.
— Any alteration or modification of this product is expressly forbidden as it may cause serious personal injury, death, property damage and/or product malfunction.
— To prevent product malfunction and/or electrical shock this product must be properly grounded.
— This luminaire is designed to operate in ambient temperatures ranging from -30°c to 40°c and to be horizontally mounted with the LEDs facing down.
— Wall mount only.
— THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION
AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED
— IN 75°C SUPPLY CONDUCTORS
— This product is not available for several special environments, such as places with corrosive gas liquids or high pressure water vapor.
MOUNTING TO A WALL
1. Open the Back Box by loosening the Locking Screw.
2. Verify and remove only necessary Gasket material where Back Box will mount.
3. Knock-out Back Box material for necessary mounting location.
4. Mount Back Box to Junction Box securely, using hardware supplied by others.
5. Connect electrical connections with fixture wiring.
6. Seal Back Box to Housing by pushing on front of Housing while tightening
Locking Screw to ensure that screw is fully seated in the Housing Recess.
Ensure wiring remains within Back Box and wires do not get pinched.
Using a silicone rubber will ensure a watertight seal.
7. If light output angle needs to be adjusted loosen screw to rotate the
fixture to desired light output angle. Tighten screw once desired light
output angle is achieved.
Wall Mount Box
150mm
135mm
151.3mm
5.31 ’’
5.96 ’’
5.9 ’’
Leveling Bubble
Hands-free
mounting hinge
Body
Wall Mount Box
G 1/2 Close Up Plugs
Photocell
EVA Gasket
Glass
Sealing ring
Serrated Safety
Washers Screw
Adjusting angle screw Screw
0° 60° 90°
WL-MAWP
Fig. 1
PHOTOCELL INSTALLATION
1. Install photocell and wire as per diagram.
2. Use photocell rated for your supply voltage.
1. Check that the line voltage at the fixture is correct.
Refer to wiring directions.
2. Is the fixture grounded properly?
3. Be sure the photocell, if used, is functioning properly.
TROUBLESHOOTING
ON-OFF WIRING
Universal voltage driver permits operation at 60 Hz except fixtures
factory ordered with a 120-277VAC (P0) or 347VAC photocell (P3)
1. Connect the BLACK fixture lead to the (+) LINE supply lead.
2. Connect the WHITE fixture lead to the (-) COMMON supply lead.
3. Connect the Yellow Green wire from fixture to supply ground.
CLEANING & MAINTENANCE
CAUTION: Be sure fixture temperature is cool enough
to touch. Do not clean or maintain while fixture is
energized.
1. Clean glass lens with non-abrasive glass cleaningsolution.
2. Do not open the fixture to clean the LED. Do not touch the LED.
BLACK
BLACKBLACK
AC
INPUT
LAMPLOAD
RED
PHOTOCONTROL
WHITE
WHITEWHITE
Black
White Neutral
Green/Yellow Green
Ground
Line
Purple
DIM+
Gray
DIM-
  • Page 1 1
  • Page 2 2

WAREHOUSE-LIGHTING COM WL-MAWP WareLight Mini Adjustable Wall Pack Installation guide

Brand
WAREHOUSE-LIGHTING COM
Model
WL-MAWP WareLight Mini Adjustable Wall Pack
Category
Motorcycle Accessories
Type
Installation guide
This manual is also suitable for

WAREHOUSE-LIGHTING COM WL-MAWP WareLight Mini Adjustable Wall Pack is a wall-mounted LED luminaire designed for outdoor use. It features adjustable light output angles, allowing you to direct the light where you need it most. The luminaire is designed to operate in ambient temperatures ranging from -30°c to 40°c and is suitable for use in a variety of outdoor applications, including architectural lighting, security lighting, and area lighting. The luminaire is easy to install and comes with all necessary hardware. It is also backed by a 5-year warranty.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents