ENGLISH
Instruction manual
DIGITAL DSP SUPPORTED MODULAR LINE ARRAY SYSTEMS
Phoenix Professional Audio GmbH
Gewerbepark Conradty 12
D-83059 KOLBERMOOR
Tel. 0049-(0)8031-30425-0
Fax. 0049-(0)8031-30425-25
www.phoenix-pa.com
shop.phoenix-pa.com
Copyright 2012 Phoenix Professional Audio GmbH, www.phoenix-pa.com
The Phoenix logo is registered at the German Patent and Trademark Office (TM).
All brands are properties of their respective owners.
DOC- 210812
Made in EU
DSP supported speaker systems which provide
a precise directional sound and high-precision
directivity by the high-quality mathematical calculation
of the optimal sound parameters by the DSP (audio
signal processor).
DigiVoice-110.8 DSP2
With 8-channel DSP.
Sound range 15 mtr.@95dB. 140 watts sine power.
DigiVoice-220.16 DSP2
With 16-channel DSP.
Sound range 25 mrt@95dB. 190 watts sine power.
Digivoice systems assembled with 3.5“ neodymium
chassis and HF magnetostatic sound converter.
Instruction manual
1. Read this instruction manual carefully.
2. Keep this instruction manual safe.
3. Observe all warnings.
4. Observe all instructions.
5. CAUTION: To avoid fires and electric shocks, this system may not be exposed to rain and humidity. Do not use this
device near waters.
6. Clean only with a dry cloth.
7. Do not cover any air vents.
8. Do not place this device close to heat sources like radiators, hot air dampers, ovens or other units (including ampli-
fiers) which release heat.
9. Do not invalidate the safety function of the inverse-polarity protection plug or the safety plug. A plug with inverse-polarity
protection has two pins, from which one is wider than the other (only for USA/Canada). A safety plug has two pins and
one ground pole (only for USA/Canada). The wide pin resp. the third pole are intended for your safety. If the included
plug does not fit in your socket, the socket is obsolete and has to be replaced by an electrician.
10. Pass the power cable in a way that nobody can step onto it or that it can be jammed. This is to apply especially for
plugs, sockets and the place where the cable comes out of the device.
11. Only use equipment and products specified by Phoenix Professional Audio GmbH.
12. Maintenance operations should only be done by qualified maintenance staff. The device has always to be maintained
if it has been damaged in any way, such as power cable or power plug is damaged, liquids have been spilt on the device
or objects have fallen into the device, if the device has been exposed to rain or humidity, if it does not operate as usual
or if it fell down.
The exclamation mark in a triangle shall advise the user of the existence of important
operation- and maintenance instructions in this manual.
The symbol consisting of a flash with an arrowhead shall advise the user of the
existence of non-insulated, dangerous voltages within the housing, which can be
strong enough to get an electric shock.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE THE
COVER. ONLY USE QUALIFIED STAFF FOR ALL MAINTENANCE WORKS.
Important safety precautions and symbol explanation
EXPLANATION OF THE GRAPHIC SYMBOLS
Instruction manual
The newly developed professional active DSP LINE ARRAYS , serie: Digivoice -110.8 DSP2 (8-channels DSP) and serie:
Digivoice-220.16 DSP2 (16-channels DSP), have been developed especially for sound transmission in acoustic difficult
areas with long reverberation times like such as churches, conference rooms, museums, cathedrals, conference centers
and halls, but also as the perfect „sound producer“ for multimedia applications.
The active DigiVoice audio systemes consist of software-controlled speakers, each of the 8 resp.16 DSP channels has
an own Class-D final stage which are regulated with different acoustic characteristics to fulfil the acoustic requirements
of the particular location.
The DSP supported speaker systems allow a precise directive sound and high-precision directivity by a high-quality
mathematical calculation of the optimal parameters by the DSP (audio signal processor).
Steady volume in the ranges @ 95 dB „NEAR FIELD“ and „WIDE FIELD“ and an excellent speech intelligibility in the
complete sound range are only some advantages of the DigiVoice serie.
Most important features are the continuous electronical controllability of sound outlet angle and inclination angle
in vertical direction in real time, without mechanical direction of the speaker systems (incline).
The Digivoice systems provide specific incline adjustment + / -45 degrees) and the vertical sound angle (6 degrees
to 14 degrees), parameterization is done by the system automatically by the digital DSP control.
Beyond that the integrated DSP audio system offers a whole lot of audio processing functions:
MAIN CONTROL (basic settings)
- Volume control / volume control (-20 dB to +6 dB)
- Delay adjustment (0 to 500 ms)
- Signal limiter with threshold (-40 dB to +6 dB) with mode: SLOW/NORMAL/FAST, adjustment
- Noise gate with LEVEL/ATTACK/RELEASE, adjustment and BYPASS.
DEVICE SETTINGS
- Automatic „SCANNING“ of the IP addresses of all networked DigiVoice speakers.
- Besides that automatic allocation of the COM PORTs with port time out and COM-port display.
BEAM CONTROL (User settings)
- Column elevation / mounting height: (distance of the floor area) with setting parameters 1.5 m to 3 m height.
- Focus distance / beam range: (directivity length while maintaining the sound pressure) according to model up to 25 meters.
- Focus elevation / beam height: height setting for the acoustic lense in the area of 0.5 to 3 meters.
- Opening angle: width setting for the acoustic lense in the aera of 6 to 14 degrees.
PEQ (parametrical equalizer)
- Selection of up to 10 PEQ elements.
- Frequency selection of 20 Hz to 20 kHz.
- Range of effects Q-factor of 0.05 to 3 OCT.
- Setting of amplification or deadening of the selected frequency of -20 dB to +12 dB.
Useful information:
A graphic presentation of the modified DSP configuration is integrated in the software under Operating Characteristic
and Beam Drawing.
GENERAL INORMATION and SYSTEM DESCRIPTION
Instruction manual
The DigiVoice system has a transformer-balanced „100V IN“ (+50dB) interface input for direct signal infeed from the
speaker network, two RJ-45 jacks (INPUT-LINK) for easy network and configuration of multiple DigiVoice systems (CAT-5
line) and a mains input terminal 230VAC.
Important:
In every place where no network lines (CAT-5) for the network of the DigiVoice systems may be passed, the
DigiVoice DSP-line arrays can be connected directly to old, existing 100V lines to the internal 100V-Audio-IN input.
After programming and measurement of the system via PC, the network lines and the programming interface
may again be removed.
The speakers are mounted flat at the wall. By the included software the acoustic characteristics are adapted to the local
conditions.
All active Digivoice Line Array systems have a modern switching power supply and fully digital 8 resp. 16 channel CLASS-D
power amplifier with DSP.
The Digivoice-110.8 DSP2 and Digivoice-220.16 DSP2 are controlled by the supplied system software ACML-CONTROL
1.5. The friendly designed user interface allow an easy and intuitive control operation in the range Audio-DSP and sound
directivity.
Only four main parameters are entered into the software ACML-CONTROLL 1.5 by the user:
1.-Mounting height
2.-Beam range
3.-Beam height
4.-Opening angle
The parameterization is done by the system via digital DSP control automatically.
5- Equalization with PEQ
To use the DigiVoice system correct and to apply all technical possibilities, you have to make a room adjustment control
resp. room equalization after the installation.
The DigiVoice systems are assembled with magnetostat sound converters and special positioned broadband chassis.
The frequency-independent directing sound is only limited to the audience area and supplies highest acoustic and
natural speech reproduction. In this way the sound reflections of the room is reduced to a minimum and the syllable
comprehensibility (STIPA values) improved enormous.
For the range and assembly of the particular line sound emitters please see the specifications.
These active DSP supported Line Array systems with their expanded frequency range in the tweeter range (magnetostat
sound converter) are excellent suitable for speech- and music transmission, and in connection with a SUB WOOFER to
consider as „FULL RANGE“ system.
GENERAL INORMATION and SYSTEM DESCRIPTION
Copyright 2012 Phoenix Professional Audio GmbH, www.phoenix-pa.com
The Phoenix logo is registered at the German Patent and Trademark Office (TM).
All brands are properties of their respective owners.
Instruction manual
SYSTEM INPUTS
All systems serie Digivoice-110.8 DSP2 and Digivoice-220.16 DSP2 have on the rear side a connection port.
At first remove the protective cover No. 1 to get to the connections of the connector port.
1 2 3
1. PROTECTIVE COVER
2. NETWORK INPUTS
RJ-45 input jacks INPUT and LINK for easy networking of the system speakers and the connection to a PowerVoice
automatic mixer by a system interface.
Important:
For the system networking please always use shielded CAT-5 lines!
3. 100V SIGNAL INPUT JACK
Serves for direct connection resp. signal feed of existing 100V speaker lines with a 100V-ON / RJ-45-OFF selector switch.
4. 230VAC INPUT JACK
Phoenix jack for connection to the 230VAC/50-60Hz power supply.
4
Copyright 2012 Phoenix Professional Audio GmbH, www.phoenix-pa.com
The Phoenix logo is registered at the German Patent and Trademark Office (TM).
All brands are properties of their respective owners.
Instruction manual
SYSTEM CONNECTION
230 V/AC
230 V/AC
230 V/AC
Interface
Audio signal,
analog input
to Interface
(XLR Port)
PC- Programming
(ACML-Control 1.8.6 Software) USB-Port
CAT.-5 /RS485+Audio
CAT.-5 /RS485+Audio
.........
Speakers
K-1-XXML
2 x RJ 45 Ports
2 x RJ 45 Ports
2 x RJ 45
Ports
Link
Link
DigiVoice-system
speaker
DigiVoice system
speaker
DigiVoice system network DigiVoice system network
PV-DSP-Automatic
Amplifier
CAT.-5 /RS485+Audio
CAT.-5 /RS485+Audio
100V Speaker Line
optional, input to „100V IN“
DigiVoice
100V speaker line
optional, input to „100V IN“
DigiVoice
Microphones
Copyright 2012 Phoenix Professional Audio GmbH, www.phoenix-pa.com
The Phoenix logo is registered at the German Patent and Trademark Office (TM).
All brands are properties of their respective owners.
Useful information:
In every place where no network lines (CAT-5/CAT-7) for networking of the DigiVoice systems may be passed, the DigiVoice
line arrays can directly be connected to old, existing 100V lines to the internal 100V-Audio-IN input.
After programming and measurement of the system via PC, the network lines and the programming interface I/O- USB
may again be removed.
Instruction manual
Copyright 2012 Phoenix Professional Audio GmbH, www.phoenix-pa.com
The Phoenix logo is registered at the German Patent and Trademark Office (TM).
All brands are properties of their respective owners..
PROGRAMMING / SYSTEM CONNECTION VIA INTERFACE
XLR-XLR
symm. audio signal
connection.
USB-USB
connection.
RJ-45
shielded line CAT-5.
OUTPUT RS 485 interface
INPUT Digivoice connection.
NETWORK
230VAC
connection.
Instruction manual
Copyright 2012 Phoenix Professional Audio GmbH, www.phoenix-pa.com
The Phoenix logo is registered at the German Patent and Trademark Office (TM).
All brands are properties of their respective owners..
MECHANICAL AND ELECTRICAL MODULE CONNECTION
Only model: Digivoice-220.16 DSP2
The new, active Digivoice-220.16 DSP2 serie has been constructed modular and consists of
two system components, which have to be connected together mechanically and electrically.
Referring to this, first of all please connect the two system plugs No. 2a and 2b together, then
put the four connecting screws No. 1a into the keyholes No. 1b. Please screw the two modules
on the rear side with the connection screw No. 3a and part No. 3b.
After screwing through the connection piece No. 3b the Digivoice-220.16 DSP2 system is ready
for use.
1a 1a 1b 1b2a 2b
3a 3b
Instruction manual
Copyright 2012 Phoenix Professional Audio GmbH, www.phoenix-pa.com
The Phoenix logo is registered at the German Patent and Trademark Office (TM).
All brands are properties of their respective owners..
SYSTEM VERBINDUNG
SOFTWARECONFIGURATION
Information for installation and operation:
IMPORTANT:
Before you can use the „ACML-CONTROL“ software, at first NET Framework 3.5 (or higher version) for Windows NT, XP
and 98 should be installed. The NET Framework 3.5 is on the installation-CD or can be installed from the Microsoft website.
Then the programme „ACML-CONTROL 1.5“ resp. „ACML-CONTROL“/Setup.exe can be installed on the PC. After the
installation the program ist started automatically.
After the network connection of all present DigiVoice systemes with D/A interface (RJ-45 inputs), the connection between
PC and D/A interface (USB interface) can be done via USB port.
In the field „SETTINGS“ the option „CONNECTION“ has to be chosen to be able to make communication with D/A interface.
When you click at the „SCAN“ button, program scans the existing COM ports and shows the connected devices. Then
please confirm the connection in the new window with OK. The connection between PC and system is established.
In the menu „GROUP“ please choose the related Digivoice system with the right mouse button:
- Submenu „ADD SPEAKER„
- Submenu “NEW DEVICE“
- for Digivoive-110.8 DSP2 <ACML2 110/8>
- for Digivoive-220.16 DSP2 <ACML2 220/16>
Instruction manual
Copyright 2012 Phoenix Professional Audio GmbH, www.phoenix-pa.com
The Phoenix logo is registered at the German Patent and Trademark Office (TM).
All brands are properties of their respective owners.
SYSTEM VERBINDUNG
SOFTWARE CONFIGURATION
Information for installation and operation:
SOFTWARE PROGRAMMING MAIN CONTROL
„VOLUME“
In the range „VOLUME“ the DigiVoice system´s volume
is adjusted digitally.
SOFTWARE PROGRAMMING MAIN CONTROL
„DELAY“ signal delay
Via mouse click at the DELAY window you get into the
submenu „DELAY“.
There is one DELAY available.
Inputs can be adjusted in [ms], [m] and [cm]. Each
DigiVoice system can have its own delay setting.
TIP:
A minimal signal delay of i.e. 2 ms has a positive effect
to feedback deficit.
A signal delay offers a correct sound by delaying
the acoustic signals in a way that there are no echo
interferences, even the speakers or amplification
systems are located far from each other.
Our digital audio signal delay is switching configurated
in studio quality and uses extensively the calculated
processing of the digitalized signal. It offers an
automatable control of the time lags via very little
quantization stages of the signal delay.
Instruction manual
SYSTEM VERBINDUNG
SOFTWARE CONFIGURATION
Information for installation and operation:
SOFTWARE PROGRAMMING MAIN CONTROL
„NOISE GATE“„LEVEL“, „ATTACK“, RELEASE“
The noise gate cuts off signals under a specific, definable
level (-90 dB to -3dB). But signals which overmatch this
level are passed unprocessed.
A typical application is noise suppression with low level.
Thereby the adjustable threshold level (LEVEL setting) is
set directly over the noise level. Eventually present noise
is thereby suppressed, as soon as the master volume of
the input signal does not underrun the LEVEL calibration.
If the master volume is higher than the LEVEL calibra-
tion, the interferences are also let passed but covered
by stronger wanted signals.
- LEVEL (-90 dB to -3 dB)
Herewith you determine the changeover level, above
this the effect of the limiter starts.
-ATTACK (20us to 5000 us)
This control determined the reaction speed of the internal
circuitry to the input signal.
The longer the ATTACK time is chosen, the later the
limiter effect starts.
With longer ATTACK times the LIMITER affects more
to the average signal level and not anymore to fast and
high peak levels.
This causes a softer limiter effect and maintains the
dynamics of the audio signal extensively, but cannot
avoide temporary overrides.
-RELEASE (1 ms to 3000 ms)
In the range RELEASE-Modi you determine, how fast
the limiter again returns to the unprocessed level of the
input signal, as soon as after signal limitation the LEVEL
is again underrun.
In case of too short release periods and signals with
high dynamic differences, undesired „PUMP“ effects
at simultaneous limited dynamics and higher overall
volume can happen.
However, longer release periods produce softer change-
overs, a compressed audio signal, but simultaneously
get the short dynamic peaks.
Copyright 2012 Phoenix Professional Audio GmbH, www.phoenix-pa.com
The Phoenix logo is registered at the German Patent and Trademark Office (TM).
All brands are properties of their respective owners.
Instruction manual
SYSTEM VERBINDUNG
SOFTWARE CONFIGURATION
Information for installation and operation:
SOFTWARE PROGRAMMING MAIN CONTROL
LIMITER „Threshold“
In the menu LIMITER you determine via the threshold
adjustment (-40 dB to +6 dB) the crossover level, over
which the limiter effect starts.
By level enhancement there will be delay of limiter start.
In the menu LIMITER you determine via ATTACK TIME
the reaction rate of the internal circuit to the input
signal.
SLOW- longer ATTACK time
MIDDLE- middle ATTACK time
FAST- fast ATTACK time
The longer the ATTACK time (SLOW position) is chosen,
the later limiter effect will start.
With longer ATTACK times, the limiter has more effect
to the average signal level and not anymore to fast and
high peak levels.
This causes a softer limiter effect and maintains the sig-
nal dynamics extensively, but cannot avoid temporary
override caused by fast signal peaks.
Useful information:
Longer attack times at percussive signals let the dy-
namic tone level „PICK“ pass, without regulating the
level down.
A „KICK DRUM“ also keeps its „PUNCH“ at longer
attack times.
Also at RECORDING resp. final mixing a litte longer
attack times will be appreciated.
To protect speakers from too high peak levels in PA
applications, short attack times are however recom-
mended (FAST setting).
Copyright 2012 Phoenix Professional Audio GmbH, www.phoenix-pa.com
The Phoenix logo is registered at the German Patent and Trademark Office (TM).
All brands are properties of their respective owners.
Instruction manual
SOFTWARE CONFIGURATION
Information for installation and operation:
The system will, caused by the inputs in the ranges
- COLUMN ELEVATION (mounting height)
- FOCUS DISTANCE (beam range)
- FOCUS ELEVATION (beam height)
- OPENING ANGLE (vertical opening angle)
make no automatic control calculation of the array
resp. the control parameters. All in the system needed
algorythms are configurated automatically.
SOFTWARE AREA BEAM CONTROL
„COLUMN ELEVATION“
The inputs in the field COLUMN ELEVATION (distance
from the floor area) are extremely important for the cor-
rect automatic calculation of the system settings!
Important information
Please consider that the measurement from the floor
area has to be done up to the lower housing edge.
Measure the distance and take the measured value
over to the software in the field COLUMN ELEVATION
(mounting height).
Important information
An optical indication in the monitor window shows au-
tomatically all setting changes of the sound level which
have been done by you.
SOFTWAREBEREICH BEAM CONTROL
„FOCUS DISTANCE“
In the field FOCUS DISTANCE the required sound range
can be adjusted by you.
Important information
Please consider the technical characteristics resp.
the maximal indicated range of the specific Digivoice
models.
Copyright 2012 Phoenix Professional Audio GmbH, www.phoenix-pa.com
The Phoenix logo is registered at the German Patent and Trademark Office (TM).
All brands are properties of their respective owners.
Mounting height!
Reference element
Instruction manual
SOFTWARE CONFIGURATION
Information for installation and operation:
SOFTWARE FIELD BEAM CONTROL
„FOCUS ELEVATION“
In the field FOCUS ELEVATION the required height of the
sound´s acoustic lense can be adjusted by you.
Useful information:
The acoustic lense height should, if possible, adjusted
to the height of the audience (ear level).
SOFTWARE FIELD BEAM CONTROL
„OPENING ANGLE“
In the field OPENING ANGLE the required vertical sound
ray opening angle can be adjusted by you.
Copyright 2012 Phoenix Professional Audio GmbH, www.phoenix-pa.com
The Phoenix logo is registered at the German Patent and Trademark Office (TM).
All brands are properties of their respective owners.
Instruction manual
SOFTWARE CONFIGURATION
Information for installation and operation:
SOFTWARE FIELD PEQ
„10 POINT PEQ“
Via mouse click to the PEQ window you get into
the submenu „PEQ“. There all audio settings for the
parametric EQ of the input range can be done.
All changes are graphically displayed in the monitor
window as trajectory curve.
Each POINT- PEQ has:
Amplification setting (G)
(-20dB bis +12 dB)
Octave setting, wing direction (BW)
(0,05 to 3,0 oct.)
Frequencies setting
(20 Hz to 20 kHz)
Useful information:
A parametric equalizer PEQ allows boosting or driving
of arbitrary frequencies with the possibility to determine
the EQ width of effects (Q factor) by yourself.
Please consider the screen display.
To be able to use the DigiVoice system correct and to
apply all technical possibilities, you have to make a
room adjustment resp. a room equalization after the
installation.
To carry out a room measurement, you need a measuring
tool. Minimum is therefor the NiniLink (Acoustilyzer)
from Neutrik or a professional measuring software like
f.i. MLSSA.
For a practical measurement the measuring microphone
must be positioned exactly at this place, where
afterwards the audience will be (f.i. in church acoustics
in the middle of the church). By installing „PINK NOISE“
to the PowerVoice amplifier measure the amplitude
frequency range with the measuring microphone.
If the appraised frequency range does not have the
aspired characteristics, an adjustment in specific areas
will be done by boosting and driving of the frequency
spectrum with room adjustment filters (PEQ).
Copyright 2012 Phoenix Professional Audio GmbH, www.phoenix-pa.com
The Phoenix logo is registered at the German Patent and Trademark Office (TM).
All brands are properties of their respective owners.
Ist-Wert
Soll-Wert
Nr.1
Instruction manual
SOFTWARE CONFIGURATION
Information for installation and operation:
Useful information:
Repeat the measuring- and adjustment procedure until
there is a linearity (see drawing No 2).
In big halls or in case of higher distance from the signal
sources (f.i. speakers) a treble dropout will happen. For
rooms with reverberation it is senseful to concentrate
additionally on the equalization of low frequencies up to
100-800 Hz. In this frequency range eich is the biggest
reverberations.
It has been shown that one should go with a lot of feeling
in the equalization zoom. It should in this case always
the efficiency of the loudspeaker and the amplifier are
considered.
Equalization for feedback suppression
The positive feedback between the microphone and
speaker generates the so-called feedback loop that
begins always at the frequency at which the transmission
curve has the strongest peak. This can be damped by
the power in the voice amplifier integrated limiter and
automatic feedback in Digivoice systems by correcting
with PEQ as follows:
First, try to reduce the disturbing frequency with the
parametric EQ to a desired value (dB) narrowband (OCT).
Then, create a feedback by increasing the microphone
sensitivity. Measure the frequency occurring and correct
them with the parametric EQ.
Then in support for mobile frequencies in Powervoice
automatic power mixer, a automatic „FEEDBACK
SUPPRESSOR“ (adaptability) to be connected.
MODI: (adaptability) VOICE POWER SYSTEM AMP
Feedback Reduction: available for a super-fast automatic
feedback suppression
ten precise notch filters are available, which are
automatically and reduce feedback
Copyright 2012 Phoenix Professional Audio GmbH, www.phoenix-pa.com
The Phoenix logo is registered at the German Patent and Trademark Office (TM).
All brands are properties of their respective owners.
ist Wert
sol Wert
Nr.1
Nr.2
Endverstärker
Vorverstärker
Lautsprecher Mikrofon
Instruction manual
Copyright 2012 Phoenix Professional Audio GmbH, www.phoenix-pa.com
The Phoenix logo is registered at the German Patent and Trademark Office (TM).
All brands are properties of their respective owners.
SPECIFICATIONS
Digivoice-110.8 DSP2
System power: 140 Watt sinus, 8 x 20 Watt (choked)
Operating mode: Active 8 x Class „D“ AMP
Frequency range: 100 Hz- 18 kHz
Sound range(*)
SPL=95dB@PINK NOISE: 15 meters
Fokus distance: < 5 to 50 meters
Typical range: 25 meters
SPL-“A“-assessment: 89dBA@PINK NOISE@25 meters
SPL-PEAK: SPL=94dB@25 meters
Assembly: 10 x 3,5“ Neodyme chassis+2 x HF magnetostatic sound converters
DSP channels: 8
Sound angle (H): 130 degrees (-6dB@1kHz-8kHz)
Sound angle (V): 6 degrees to 14 degrees (setting DSP/SOFTWARE)
Input sensitivity: 0dB on XLR interface or +50dB@100V signal IN (Phoenix jack)
Input impedance: LINE (15 kOhm), 100V (40 kOhm)
Input level: -20dB<+6dB
Delay: to 170 meters
Input limiter: -40dB<+6dB
Limiter: SLOW / NORMAL / FAST
Noise Gate: (Level/Attack/Relaise) -90dB<-3dB/300us<5000us/1ms<3000ms
Equalization: 10 point PEQ
Parametric EQ: 10 point PEQ
< 20 Hz >20 kHz
< -20 dB > +12 dB
< 0.05/ oct > 3 dB/oct
D/A- Interface: 1 x USB, 2 x RJ-45/RS 485, 1 x XLR-Audio IN
Interface DigiVoice: RS 485 duplex, 2 x RJ-45 (IN/LINK)
Software: from version 1.8.6
Power supply: 230VAC/50-60 Hz
Power consumption@open circuit: 20VA
Power consumption@MAX: 200VA
Dimensions: H-1156 mm x W-102 mm x D-98 mm
Housing / Grille: Aluminium profile / powder-coated perforated sheet
Weight: 5,8 kg
(*) opening angle @ 6 degrees
Instruction manual
Copyright 2012 Phoenix Professional Audio GmbH, www.phoenix-pa.com
The Phoenix logo is registered at the German Patent and Trademark Office (TM).
All brands are properties of their respective owners.
SPECIFICATIONS
Digivoice-220.16 DSP2
System power: 190 watts sine, 16 x 20 Watt (choked)
Operating mode: Active 16 x Class „D“ AMP
Frequency range: 90Hz- 18 kHz
Sound range(*)
SPL=95dB@PINK NOISE: 25 meters
Focus distance: < 5 to 70 meters
Typical range: 50 meters
SPL-“A“-assessment: 91dBA@PINK NOISE@25 meters
SPL-PEAK: SPL=98dB@25 meters
Assembly 13 x 3,5“ neodyme chassis+ 3 x HF magnetostatic sound converter
DSP channels: 16
Sound angle (H): 130 degrees (-6dB@1kHz-8kHz)
Sound angle (V): 6 degrees to 14 degrees (setting DSP/SOFTWARE)
Input sensitivity: 0dB at XLR interface or +50dB@100V signal IN (Phoenix jack)
Input impedance: LINE (15 kOhm), 100V (40 kOhm)
Input level: -20dB<+6dB
Delay: to 170 meters
Input limiter: -40dB<+6dB
Limiter: SLOW / NORMAL / FAST
Noise Gate: (Level/Attack/Relaise) -90dB<-3dB/300us<5000us/1ms<3000ms
Equalization: 10 point PEQ
Parametric EQ: 10 point PEQ
< 20 Hz >20 kHz
< -20 dB > +12 dB
< 0.05/ oct > 3 dB/oct
D/A- Interface: 1 x USB, 2 x RJ-45/RS 485, 1 x XLR-Audio IN
Interface DigiVoice: RS 485 duplex, 2 x RJ-45 (IN/LINK)
Software: from Version 1.8.6
Power supply: 230VAC/50-60 Hz
Power consumption@open circuit: 30VA
Power consumption@MAX: 260VA
Dimensions: H-2312 mm x W-102 mm x D-98 mm
Weight: 9,0 kg
Housing / Grille: Aluminium profile / powder-coated perforated sheet
(*) opening angle @ 6 degrees
Instruction manual
DigiVoice- LINE ARRAY systems (range @ SPL=95dB/PINK NOISE)
15 m 25 m
DigiVoice-110.8 DSP2
DigiVoice-220.16 DSP2
SPECIFICATIONS
ADDITION
The Digivoice-110.8 DSP2 and Digivoice-220.16 DSP2 have an especially slim size for optimal opti-
cal results, also in listed ares.
Special powder-coatings according to the RAL numbers are possible on request.
It can be said that the new DigiVoice systems have a top design in the range audio speakers due
to their technical possibilities and their very slim size.
The standard to a perfect architectural integration and highest sound quality of Phoenix Professional
Audio GmbH is underscored by ever and anon new innovations.
Many very successful projects prove the attractivity and quality of the products.
Instruction manual
NOTES
/
