Phoenix ZP-40 SLIM/2 User manual

Brand: Phoenix

Model: ZP-40 SLIM/2

Type: User manual

This manual is also suitable for

ZP-40 SLIM

ENGLISH

Instruction manual

MOBILE PROCESSION SYSTEM WITH CLASS T- AMPLIFIER

Phoenix Professional Audio GmbH

Gewerbepark Conradty 12

D-83059 KOLBERMOOR

Tel. 0049-(0)8031-30425-0

Fax. 0049-(0)8031-30425-25

www.phoenix-pa.com

shop.phoenix-pa.com



www.phoenix-pa.com / shop.phoenix-pa.com“

Phoenix Logo is registered at the German Patent and Trademark Ofﬁce (TM)

All brands are property of their respective owners.

Procession systems

ZP-40 SLIM

ZP-40 SLIM/2

DOC-040413

Made in EU

DIGITAL

AMPLIFIER

NEODYNIUM

SPEAKERS

WIRELESS SYSTEM

USB PLAYER

NICKEL HYDRID

ACCUMULATOR

TECHNICS

4,9 KG LIGHTWEIGHT

Procession system ZP-40 SLIM



Made in Europe

1. Carefully read this manual.

2. Keep this manual well.

3. Consider all warnings.

4. Follow all instructions.

5. ATTENTION: to avoid ﬁres and electric shocks, this system may not be exposed to rain and humidity. Do not use

this device close to waters.

6. Clean it only with a dry cloth.

7. Do not cover any air vents.

8. Do not place it close to heat sources like radiators, hot air dampers, ovens or other devices (including ampliﬁers),

which emit warmth.

9. Do not override the safety function of the inverse-polarity protection or the safety plug. A plug with inverse-polarity

protection has two pins, one of them is wider than the other (only for USA/Canada). A safety plug has two pins and

one ground pole. If the included plug does not ﬁt into your socket, the socket is obsolete and has to be replaced by

an electrician.

10. Pass the mains cable in a way, that nobody can step onto it and that it cannot be jammed. This is especially valid

for plugs, sockets and the place where the cable comes out of the device.

11. Only use products and accessories speciﬁed by Phoenix Professional Audio GmbH.

12. Let maintenance operations only be carried out by qualiﬁed maintenance staff. The device has always to be

maintained if it has been damaged in any way, f.i. when the power cable or the mains plug is damaged, if liquids has

been spilt onto the device or objects has been fallen into it, if the device has been exposed to rain or humidity, if it

does not operate normally or it has been fallen down.

The exclamation mark in a triangle shall advise the user of the existence of important

operation- and maintenance instructions in this manual.

The symbol consisting of a ﬂash with an arrowhead in a triangle shall advise the user

of the existence of non-insulated, dangerous voltages within the housing, which can

be strong enough to give an electric shock.

ATTENTION: TO REDUCE THE RISK OF AN ELECTRIC SHOCK, DO NOT REMOVE

THE COVER. USE QUALIFIED STAFF FOR ALL MAINTENANCE OPERATIONS.

EXPLANATION OF THE GRAPHIC SYMBOLS

IMPORTANT SAFETY PRECAUTIONS

www.phoenix-pa.com / shop.phoenix-pa.com“

Phoenix Logo is registered at the German Patent and Trademark Ofﬁce (TM)

All brands are property of their respective owners.

Procession system ZP-40 SLIM



Made in Europe

GENERAL

The newly developed mobile sound system (procession system) ZP-40 SLIM is a state-of-the-art sound

system which absolutely convinces the user by its powerful speech- and music transmission resp. the in-

ternal, electronic and mechanic design.

Usable also as stationary sound system in your church.

The procession system has two separate power channels (2 x 20 W sine) based upon the digital T-CLASS

ampliﬁers which drive each two powerful, microlight Neodynium 3.3“ speaker chassis.

Besides this, the ZP-40 SLIM procession system has up to two (version ZP-40 SLIM/2) free of charge UHF

receiver, two hand wireless microphones (sender) in the range 863 MHz to 865 MHz frequencies.

The standard built in SD-CARD/USB player (player for USB-STICKS/PEN DRIVE and SD storage cards) will

always support you with the processions or as a stationary sound system in your church as background

music source.

A big advantage of the ZP-40 SLIM system is the very simple and user-friendly operation. All connections

are placed ergonomically shaped, very clear and well comprehensible.

The system ZP-40 SLIM is equipped with powerful and very light-weight nickel-metal hydrid accumulator

(NiMH).

The nickel-metal hydrid accumulators (NiMH) distinguish themselves by high energy density, they are heat-

resisting and are no subject to memory effect.

The Coulomb efﬁciency is typically approximately 100 %, that means almost the complete electric current

loaded in the accumulator can also be taken from it again.

Reaching the target service life of typically 500 load cycles (this corresponds to ten years with weekly load)

is provided by the intelligent, internal, controlled loading system with deep discharge protection. The ope-

rating time with full accumulator is approx. 6 hours.

POWER

RADIO TECHNOLOGY

SD/USB-PLAYER

OPERATION

BATTERY TECHNICS

www.phoenix-pa.com / shop.phoenix-pa.com“

Phoenix Logo is registered at the German Patent and Trademark Ofﬁce (TM)

All brands are property of their respective owners.

Procession system ZP-40 SLIM



Made in Europe

1 2 3 4 5

6 7 8

FRONT SIDE

CONTROL ELEMENTS OF THE FRONT SIDE

1.- multi-functional display of the USB player

2.- IR-remote control receiver input of the USB player

3.- USB/SD

This button is used for shifting between USB operation and SD card opera-

tion. IMPORTANT: the function is only given if simultaneously two storage

media are located in the USB player.

4.- REPEAT

By short pressing the button REPEAT appears „ONE“ at the display and

the current song is repeated. By pressing again appears „ALL“ at the dis-

play and all songs which are located at the USB stick are repeated. The

function is switched off by keeping the REPEAT button pressed for approx.

3 seconds, then the device changes to normal PLAY MODE.

5.- PLAY/II (PAUSE)

By pressing the PLAY button a song is started. Press the button while a

song is played, the playback is stopped. „PAUSE function“: press the but-

ton again and the playback is started.

6.- SD-CARD SLOT

7.- USB SLOT

Procession system ZP-40 SLIM



Made in Europe

CONTROL ELEMENTS OF THE FRONT SIDE

8.- MUTE (MUTING)

By pressing the MUTE button the playback is interrupted, the program resp. the current song is, however,

not stopped by the system, it continues playing in the system.

9.- LINE OUT (OPTION)

At the rear side there is a XLR-output LINE 0 dB.

The extension output is used as audio connection for further ampliﬁers or as signal connection for a sound

system in your church. So the procession system ZP-40 SLIM can be used as wireless receiver for the

delivered wireless microphones and as player for your songs.

10.- TX1 and TX2 LED DISPLAY

Up to two wireless receivers can be mounted into our ZP-40 SLIM, the LED TX1 shows the active transmission

path of the ﬁrst wireless receiver, the second LED TX2 shows the active connection of the second wireless

receiver.

11.- 2-BAND EQ

Separate LF- and HF-control for the signal equalization resp. equalization of the speech reproduction of

the wire-less transmission.

12.- VOLUME CONTROL (RADIO RANGE)

These controls determine the volume of the reception.

13.- 2-BAND EQ

Separate LF- and HF-control for the signal equalization resp. equalization of the speech reproduction and

music transmission for all devices which are connected to the Cinch jack and for the jack plug and the

dynamic microphone which is connected there.

14.- VOLUME CONTROL (EXPANSION MICROPHONE AND CD RANGE)

These controls determine the volume for the inputs MICROPHONE & CD.

15.- MICROPHONE INPUT RANGE

This jack plug is used to connect wired, dynamic microphones.

The expansion microphone is not in the scope of supply.

16.- LINE INPUT TO CINCH

Line input (0 dB) with volume control No. 14, LF and HF-EQ actuator No. 13 for f.i. CD-player feed etc. for

the front input.

17/18.- NETZ ON-/OFF SWITCH WITH OPERATION DISPLAY

After operating this switch, the device is ready for operation. The green LED display lights when the device

is switched on (POWER ON).

The procession system ZP-40 SLIM resp. ZP-40 SLIM/2 can also be connected to the charging device also

during operation (charging process active).

www.phoenix-pa.com / shop.phoenix-pa.com“

Phoenix Logo is registered at the German Patent and Trademark Ofﬁce (TM)

All brands are property of their respective owners.

Procession system ZP-40 SLIM



Made in Europe

19.- LOW BATT. OPERATION DISPLAY

The red LED display does not light, when the procession system is switched on (POWER ON), and the

accumulator is sufﬁciently charged resp. shows enough energy for the operation.

The LED display only lights „RED“, when the accumulator us unloaded and when there is only residual

energy available to operate the system. Then the system has to be charged!

IMPORTANT:

Should the red LED display activate itself, you have approx. 30 seconds time to connect the procession

system to the charging device. The system is switched off by the control system and the deep discharge

protection is active.

The procession system ZP-40 SLIM resp. ZP-40 SLIM/2 can be connected to the charging device and

loaded also during the operation (charging process active).

Please carry out the charging process as long until the yellow LED display No. 20 [LOAD] extinguishes.

20.- LOAD OPERATION DISPLAY

The orange LED display lights, when the automatic charging system is activated and only as long until the

accumulator is fully charged.

Please carry the charging process out like follows:

1- plug the coupling socket of the charging device into the input No. 21.

2- supply the deliverd charging device with mains voltage 230VAC/50Hz.

The charging process is activated automatically and the orange LED display lights. This process can last

up to 10 hours.

The charging process is interrupted automatically when the accumulator is fully loaded.

A personal supervision of the charging process by the user is not necessary.

3- Should the [LOAD] display be expired, please at ﬁrst separate the charging device from the mains voltage

and then separate the charging device from the procession system resp. the plug from the jack No. 21

[24VDC].

21 .- 24VDC INPUT (mains operation and loading input)

The built-in 24VDC jack is used as power supply 24VDC for so-called mains operation with accumulator

control and at the same time as input for the charging process.

Please consider the chapter 20/ 20.- LOAD. OPERATOIN DISPLAY.

22.- TRIPOD FLANGE/SHOULDER STRAP BRACKET

At the lower part of the procession system there is a ﬂange located with 35 mm diameter for tripod recording.

Thereby the sound system ZP-40 SLIM can also be used as stationary system in your church or for church

services in the outdoor area.

IMPORTANT:

The lower ﬂange is at the same time used as recording for the supplied shoulder strap.

CONTROL ELEMENTS OF THE FRONT SIDE

www.phoenix-pa.com / shop.phoenix-pa.com“

Phoenix Logo is registered at the German Patent and Trademark Ofﬁce (TM)

All brands are property of their respective owners.

Procession system ZP-40 SLIM



Made in Europe

HORIZONTAL JUSTIFICATION OF THE SPEAKERS

The upper speaker segment in the procession system ZP-40

SLIM is pivotable in the horizontal level and is used to arrange

the sound reﬂection of the speakers optimally to the wanted ran-

ge where the sound shall be transmitted.

The upper segment can be rotated up to 180 degrees conti-

nuously and provides the best speaker justiﬁcation for a FRONT/

REAR sound of the procession or as „wide dispersion angle“

resp. adjustable dispersion angle for frontal ampliﬁcation.

PICTOGRAMS SYMBOLIC PRESENTATION OF THE JUSTIFICATION

Front- and rear am-

pliﬁcation, drawn-

out procession.

Front ampliﬁcation

with wide dispersi-

on angle.

Procession system ZP-40 SLIM



Made in Europe

WIRELESS MICROPHONES CONTROL ELEMENTS

Battery case for 9V monobloc bat-

teries. Please always pay attention

to the correct polarization!

Battery condition display LED [LOW BAT].

The red LED lights, when the battery capacity

comes to the end.

Then please change the battery.

ON- and OFF-switch with MUTE position.

To the MUTE position can be shifted when the speaker makes longer breaks or does not wish a trans-

mission via the speakers.

The MUTE position has, different to the OFF position, the advantage that with the MUTE position there

are no disturbing switch-on noises are developed (crack noise).

In the MUTE position the HF-carrier is held and displayed in the system via the corresponding LED-

display „TX-1“ or „TX-2“.

www.phoenix-pa.com / shop.phoenix-pa.com“

Phoenix Logo is registered at the German Patent and Trademark Ofﬁce (TM)

All brands are property of their respective owners.

Procession system ZP-40 SLIM



Made in Europe

OPTIONAL EQUIPMENT

Please contact us when you need additional equipment for the ZP-40 SLIM resp. ZP-40 SLIM/2.

Optional equipment:

- Pocket transmitter with clip-on microphone ZP-40 LAV

- Pocket transmitter with headset microphone ZP-40 LAV

- Stationary UHF-radio receiver for signal transmission to the existing sound system in your church:

WS-1000X or WS-1000R2 UHF-radio receiver [1 U].

Possible free radio freqencies: 863.100 MHz, 863.900 MHz, 864.500 MHz, 864.900 MHz.

- Speaker stand Z-40 BOX

- customer-oriented special solutions, custom-ﬁtted procession systems with several radio trans-

mitters or receivers are possible!

SYSTEM ILLUSTRATION

The illustration shows

procession system

ZP-40 SLIM/2

The illustration shows

procession system

ZP-40 SLIM

1 x mains charger

1 x shoulder strap

SPECIFICATIONS

ZP-40 SLIM/2

Output power: 2 x 20 W sine (40 W)

Ampliﬁer: 2 channel digital Class T

Equalization: 1 x LF/HF Filter radio receiver

1 x LF/HF Filter in the system

Volume control: 1 x for the wireless system

1 x for the system

Speakers: 4 x 3.5“ broad band, Neo-

dynium

turnable

Frequency response: 100 Hz to 18 kHz [+/-2 dB]

Sound pressure: 98 dBA value@1W/1mtr.

Audio inputs: 1 x USB-Player

1 x SD-Player

1 x Mic. to plug

1 x LINE to Cinch

2 x radio receiver

Audio outputs: 1 x LINE to XLR (from 01.06.13)

Remote control: IR-System for SD/USB-Player

Antenna: threadable exterior antenna

Battery technics: Nickel metal hydrid (NiMH)

Charge: approx. 10 hours [automatic]

Operating time: approx. 6 hours

Radio technology: 2 x UHF-receivers [on

board]

2 x UHF-hand microphones [sender]

Kind of reception: UHF free of charge

Range [system]: 150 mtr.

Range [wireless]: 70 mtr.

Voltage supply: 24VDC external power supply

Tripod ﬂange: yes, with 35 mm drill

Material: ALU powder-coated

Weight: 4.9 kg with accumulators

Holder: Shoulder strap

Dimension: 140 cm long

Procession system ZP-40 SLIM



Made in Europe

ZP-40 SLIM

Output power: 2 x 20 W sine (40 W)

Ampliﬁer: 2 channel digital Class T

Equalization: 1 x LF/HF Filter radio receiver

1 x LF/HF Filter in the system

Volume control: 1 x for the wireless system

1 x for the system

Speakers: 4 x 3.5“ broad band, Neo-

dynium

turnable

Frequency response: 100 Hz to 18 kHz [+/-2 dB]

Sound pressure: 98 dBA value@1W/1mtr.

Audio inputs: 1 x USB-Player

1 x SD-Player

1 x Mic. to plug

1 x LINE to Cinch

1 x radio receiver

Audio outputs: 1 x LINE to XLR (from 01.06.13)

Remote control: IR-System for SD/USB-Player

Antenna: threadable exterior antenna

Battery technics: Nickel metal hydrid (NiMH)

Charge: approx. 10 hours [automatic]

Operating time: approx. 7 hours

Radio technology: 1 x UHF-receivers [on

board]

1 x UHF-hand microphones [sender]

Kind of reception: UHF free of charge

Range [system]: 150 mtr.

Range [wireless]: 70 mtr.

Voltage supply: 24VDC external power supply

Tripod ﬂange: yes, with 35 mm drill

Material: ALU powder-coated

Weight: 4.8 kg with accumulators

Holder: Shoulder strap

Dimension: 140 cm long

Important information

For all sides of this instruction is valid:

Technical modiﬁcations and printing errors reserved.

The illustrations are similar, colour deviations reserved.

www.phoenix-pa.com / shop.phoenix-pa.com“

Phoenix Logo is registered at the German Patent and Trademark Ofﬁce (TM)

All brands are property of their respective owners.

IMPRESSIONS

Procession system ZP-40 SLIM



Made in Europe

10.

www.phoenix-pa.com / shop.phoenix-pa.com“

Phoenix Logo is registered at the German Patent and Trademark Ofﬁce (TM)

All brands are property of their respective owners.

Phoenix ZP-40 SLIM/2 User manual

Brand: Phoenix

Model: ZP-40 SLIM/2

Type: User manual

This manual is also suitable for

ZP-40 SLIM

Download PDF

report

Phoenix ZP-40 SLIM/2 User manual

This manual is also suitable for

Phoenix ZP-40 SLIM/2 User manual

Related papers

Other documents