Owner’s/Installation
Manual
Model: MV1055
For operational or technical assistance, after reading this manual,
please call us toll free at (800) 638-3600 or visit www.magnadyne.com
10.2” Flip-down Widescreen
Multimedia System
2
Driving: Be aware of road and traffic conditions. Keep
the volume at a low level.
Moisture: Do not expose the product to water or
excessive moisture. This could cause electrical
shorts, fire or other damage.
Parking: Parking in direct sunlight can produce very high
temperatures inside your vehicle. Give the car interior a
chance to cool down before starting playback.
Proper Power Supply: This product is designed to oper-
ate with a 12 Volt DC, negative ground battery system.
Protecting the Disc Mechanism: Avoid inserting any for-
eign objects into the slot of this player. Failure to observe
this precaution may cause malfunction of this
unit.
Repairs: Contact our customer service representa-
tives. Do not attempt to disassemble or adjust this
product yourself.
Installation:
The unit should be installed in a horizontal
position.
Cleaning: Use a soft cloth with some purified water to
clean the screen. Do not use any cleaner or chemi-
cal to clean the screen. Usually, a dry cloth will do.
Warnings:
Be careful not to drop or apply undue pressure to the
front panel of monitor. If the screen cracks due to mis-
use, the warranty will be voided!
The driver should neither watch the display nor
operate the system while driving.
Watching the display or operating the system will
distract the driver from looking ahead of the vehicle
and can cause accidents. Always stop the vehicle
in a safe location and use the parking brake before
watching the display or operating the system. In
some states and countries, passengers are also pro-
hibited from watching the display.
Never install the product in a location where it inter-
feres with your field of vision.
Safety Information
CAUTION:
THIS MOBILE DVD PLAYER IS A CLASS I LASER
PRODUCT. HOWEVER, THIS MOBILE DVD PLAYER USES
A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE
HAZARDOUS RADIATION EXPOSURE IF DIRECTED.
BE SURE TO OPERATE THE MOBILE DVD PLAYER
CORRECTLY AS INSTRUCTED. USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN
COVERS AND DO NOT REPAIR YOURSELF. REFER
SERVICING TO QUALIFIED PERSONNEL.
CAUTION:
FCC REGULATIONS STATE THAT ANY UNAUTHORIZED
CHANGES OR MODIFICATIONS TO THIS EQUIPMENT
MAY VOID THE USER’S AUTHORITY TO OPERATE IT.
WARNING:
• TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO
RAIN OR MOISTURE.
• THIS DEVICE IS INTENDED FOR CONTINUOUS
OPERATION.
• TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK AND ANNOYING INTERFERENCE, USE
ONLY THE RECOMMENDED ACCESSORIES.
This product incorporates copyright protection technol-
ogy that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by
Magnadyne Corporation and other rights owners. Use of
this copyright protection technology must be authorized
by Magnadyne Corporation and is intended for home
and other limited viewing uses only unless otherwise
authorized by Magnadyne Corporation. Reverse engi-
neering or disassembly is prohibited.
Region Management Information:
This Mobile DVD Player is designed and manufactured
to respond to the Region Management Information
that is recorded on a DVD disc. If the Region number
described on the DVD disc does
not correspond to the
Region number of this Mobile DVD Player, this Mobile
DVD Player cannot play this disc.
Entertainment Center Functions and Locations . . . 3-4
Remote Control Functions and Locations . . . . . . . 4
System Menu Setup . . . . . . . . . . . . . . . . . . . . . 5
TFT Menu Setup . . . . . . . . . . . . . . . . . . . . . . . 6
Audio Control . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Playing a Movie Disc. . . . . . . . . . . . . . . . . . . . . 8-10
Playing a MP3 File . . . . . . . . . . . . . . . . . . . . . 10-12
Auxiliary Audio/Video Inputs . . . . . . . . . . . . . . . . 12
Dome Light Operation . . . . . . . . . . . . . . . . . . . . 13
Headphone Operation . . . . . . . . . . . . . . . . . . 13
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Index
Use this Product Safely
3
Entertainment Center Functions and Locations
1. USB Slot: Insert a USB drive to play videos, view
pictures or listen to music. Use the controls on the
MV1055 or remote control to access the files on
the drive.
2. SD Card Slot: Insert a SD card with the contacts
facing towards the roof to play videos, view pic-
tures or listen to music. Use the controls on the
MV1055 or remote control to access the files on
the SD card.
3.
3.5mm Auxiliary Audio/Video Input Jack: Plug-in
a device with a 3.5mm audio/video input plug
to
play videos, view pictures or listen to music. The
MV1055 will not control the device so use the con-
trols on the input device to access files.
4.
3.5mm Headphone Jack: Plug-in headphones with a
3.5mm jack to hear the audio.
Note: Headphone will only work when the internal
speakers are activated. (see page 7)
5.
Disc Slot: Insert a disc into the slot with label facing up.
6. Dome Lights
7. IR Repeater
: The audio signal is converted to an
infrared light and transmitted to the headphones.
8. Mode Button:
Press to select between sources:
DVD, AV1 (internal audio/video RCA inputs) or
AV2 (external 3.5mm audio/video input jack).
9. Dome Light Door Button: When the vehicle’s door
is open the dome lights automatically turn on. To
turn off the dome lights when the vehicle’s door is
open press the button.
10. System Menu Button: Press the button to
access the TFT Menu Setup features.
11. Remote Control Sensor: Point the remote control
at this area to remotely control the MV1055.
12. Dome Light Button: Press the button to turn
on or off the dome light.
13. Disc Eject/TFT Menu Adjustment Button: Press
the button to eject the disc from the unit.
Note: For TFT Menu Setup button function refer
to the TFT Menu Setup section of this manual for
more information. (Page 6)
1
2
3
4
6
7
M
O
D
E
5
11
8
13
9
10
12
14
15
16
4
Entertainment Center Functions and Locations (continued)
14. Disc Stop/TFT Menu Adjustment Button: Press
the button to pre-stop disc play. Press the
play button to resume play where the disc
play was stopped. Press the button twice to
stop disc play then press the play button to
start play from the beginning of the disc.
Note: For TFT Menu Setup button function refer
to the TFT Menu Setup section of this manual for
more information. (Page 6)
15. Power Button: Press this
button to turn the
entertainment center on or off.
16. Play/Pause Button:
Press the button to pause
play, press again to resume play.
Remote Control Functions and Locations
Note: Install the battery before operating the remote.
1. Power Button: Press this button to turn the
entertainment center on or off.
2. TFT Menu Button: Press to access the TFT Menu
Setup features of the MV1055.
3. Channel - and + Buttons: No function.
4.
Mode Button (AV/TV DVD): Press to select between
sources: DVD, AV1 (internal audio/video RCA inputs)
or AV2 (external 3.5mm audio/video input jack).
5. Auto Button: No function.
6. Numeric Key Pad
7. Eject Button : Press to eject the disc.
8. Play/Pause Button:
Press the button to pause
play, press again to resume play.
9.
Backwards and Forward Play Buttons: Use
these buttons to change the play speed to x2, x4, x8
or x20 either backwards ( ) or forwards ( ).
10. DVD Menu Button: Press to access the DVD’s
menu features.
11. Navigation Buttons: Press to navigate in menus
up, down, left or right.
12. Enter Button: Confirms the selected item.
13. Return Button: Returns to previous menu in MP3
mode.
14. Disc, SD Card and USB Mode Selector: Press to
select between DISC (DVD/CD), CARD (SD card)
or USB (USB drive) mode.
15. DVD Audio Button (R/L): Changes the language
on multi-language movie disc.
16.
Volume Buttons: Press the VOL + to increase the
volume or press the VOL - to decrease the volume.
17. Mute Button: Mutes the volume.
18. Repeat Button: Press to repeat chapters, titles,
tracks and discs.
19. Stop Button: Press to pre-stop disc play. Press
the play button to resume play where the disc
play was stopped. Press the button twice to stop
disc play then press the play button to resume
play from the beginning of the disc.
20. Next and Previous Selection: In the movie mode
pressing these buttons will select the next or pre-
vious chapter. In the music mode pressing these
buttons will select next or previous track/file.
21. Setup Button: Access the System Setup menus.
22.
Display Button (DISP): Displays source information.
23. Program Button: Programs play sequence.
24. Subtitle Button: Accesses movie disc’s subtitle
languages.
25.
Title Button: Displays title information if available.
26. Zoom Button: Enlarges or reduces the size of
picture.
27. A-B Button: Record a selected section of a movie
or music to play repeatedly.
TFT
MENU
CH +
CH -
AV/T V
DV D
AU TO
1 2 3 4
5 6 7 8
9 0
+1 0
ST OP
REPEAT
DV D
MENU
DISP
SETUP
ENTER
PROGRAM
RETURN
TITL E
SUBTITLE
SD
US B
R/ L
A- B
ZOOM
VO L+ VOL-
1
2
3
4
5
6
7
8
9
10
11
13
15
14
12
16
17
18
19
20
21
22
24
25
23
26
27
5
System Menu Setup
System Menu Setup:
1. Press the SETUP button on remote control to enter
the system menu setup screen.
2. Use the , , and buttons to select the menu
item you want to change.
3. Once the menu item is selected, press the but-
ton to activate options for that menu item.
4. Use the and buttons to select the option you
want then press the ENTER button.
5. Press the SETUP button to exit the system menu
setup screen.
System Menu Setup Items:
TV SYSTEM
PAL
NTSC
AUTO
POWER RESUME (The disc play will resume play-
ing when the power was turned off )
ON
OFF
AUTO PLAY SETTING (Disc auto play)
ON
OFF
TV TYPE
4:3 PS
4:3 LB
16:9
PASSWORD (Password to lock Ratings menu)
_ _ _ _
1. Enter the password “0000” and press the ENTER
button. The unlock symbol will appear next
to _ _ _ _.
2. Go to the Rating sub-menu and make the neces-
sary change.
3. Return to the Password sub-menu and enter
“0000” password and press the ENTER button.
The lock symbol will appear next to _ _ _ _.
The system is now password protected.
RATING (For movies)
1 KID SAFE
2 G
3 PG
4 PG13
5 PG-R
6 R
7 NC-17
8 ADULT
DEFAULT (Return all setting to default settings)
RESTORE
Language Setup Items:
OSD LANGUAGE (On Screen Display language)
ENGLISH
CHINESE
GERMAN
SPANISH
FRENCH
PORTUGUESE
RUSSIAN
AUDIO LANG
CHINESE
ENGLISH
RUSSIAN
SPANISH
GERMAN
PORTUGUESE
SUBTITLE LANG
CHINESE
ENGLISH
RUSSIAN
SPANISH
GERMAN
PORTUGUESE
MENU LANG
CHINESE
ENGLISH
RUSSIAN
SPANISH
GERMAN
PORTUGUESE
DV D
MENU
DISP
SETUP
ENTER
PROGRAM
RETURN
TITL E
SUBTITLE
TV SYSTEM
POWER RESUME
AUTO PLAY
TV TYPE
PASSWORD
RATING
DEFAULT
6
TFT Menu Setup
TFT Menu Setup:
1. Press the button on the MV1055 to enter the TFT
Menu Setup screen.
2. When the menu appears on the screen press the
button to select the menu item: Picture, Volume,
Option, System and Clock.
3. Press the MODE button to select the sub-menu
items.
4. Use the and buttons to adjust the sub-
menu item.
5. After approximately 10 seconds of no button activ-
ity the TFT Menu Setup screen will disappear.
Menu Item
Sub-menu
Items
TFT Menu Setup Items:
PICTURE (Adjust the picture quality)
BRIGHTNESS
CONTRAST
COLOR
RESET
VOLUME
VOLUME
IR (Infrared audio signal to wireless headphones)
(Select IR-A when using MovieVision
headphones)
FM (Transmits audio over a FM radio station to
vehicle’s radio)
Note: For MV1055 internal speakers and 3.5mm
headphone jack to operate both IR and FM sub-
menus need to be set in the OFF position.
OPTION
ENGLISH (Menu Language)
ZOOM 16:9 or 4:3
SYSTEM
S-COLOR (No selection available)
CLOCK Note: Clock is a 24 hour clock.
SLEEP (Select a time for the sleep timer)
TIME (Use the to adjust the hours)
(Use the to adjust the minutes)
OFF-TIME: (Use to turn OFF the system at a
predetermined time)
ON-TIME: (Use to turn ON the system at a
predetermined time)
Selecting Menu Items
Selecting Sub-Menu Items
Adjusting Sub-Menu Items
M
O
D
E
7
Audio Control
Playing Audio Through IR Headphones:
In the TFT Menu under the Volume sub-menu make
sure the IR setting is IR-A. (IR-A setting is for
MovieVision wireless headphone, HP-400)
Note: Audio will not play through the MV1055
internal speakers or the 3.5mm headphone jack.
IR-A
Playing Audio Through the Vehicle’s Radio:
1. In the TFT Menu under the Volume sub-menu
make sure the FM setting is on one of the avail-
able radio frequencies not presently being used
by a radio station. (87.7, 87.9, 88.1, 88.3,
88.5, 88.7,88.9, 106.7, 107.1 or 107.5MHz)
2. Tune in the vehicle’s FM radio to the frequency
selected in the FM settings sub-menu.
Note: Audio will not play through the MV1055
internal speakers or the 3.5mm headphone jack.
Radio
Frequency
Set to
Off
Internal Speakers
3.5mm
Headphone Jack
Playing Audio Through the System’s Internal
Speakers or 3.5mm Headphone Jack:
1. In the TFT Menu under the Volume sub-menu
make sure the IR and FM setting are set to OFF.
2. Use the volume control on the remote to adjust
the volume level.
Note 1: When a headphone is plugged into the
3.5mm jack the internal speakers will be muted.
Note 2: Audio will not play through the vehicle’s
radio or through the wireless headphones.
8
Playing a Movie Disc
Inserting a Disc:
1. Press the power button to turn the unit on.
2. Insert a disc into the player with the label on the
disc facing upward.
3. The disc will automatically load and start playing.
Ejecting the Disc:
Press the eject button on the system to eject
the disc. You can also use the eject button on
the remote control to eject the disc.
Pausing the Disc:
Press the pause button on the system pause
disc play. Press the button again to resume disc
play. You can also use the pause button on the
remote control
M
O
D
E
Stopping the Disc:
Press the button to pre-stop disc play. Press
the play button to resume play where the disc
play was stopped. Press the button twice to
stop disc play then press the play button to
start play from the beginning of the disc.
Accessing the DVD Menu Screen:
Press the DVD/MENU button to access the DVD
menu screen. Use the navigation buttons , ,
and to select the desired menu option. Press
the ENTER button to confirm your selection.
DV D
MENU
DISP
SETUP
ENTER
PROGRAM
L
a
b
e
l
F
ac
i
ng
U
p
Mode Selection:
To select the DVD source press the MODE button
until “DVD” appears on the screen. The system will
automatically start to play the DVD.
M
O
D
E
9
Backward and Forward Play Buttons:
To play the disc backwards press the button
and the disc will play in reverse at 2 times normal
playback (x2), continually press the button to
select x4, x8 or x20 reverse play. To play the disc
fast forward press the button and the disc will
play at 2 times normal playback (x2), continually
press the button to select x4, x8 or x20 fast
forward play. Press the pause button at any
time to stop fast reverse or fast forward play.
ST OP
REPEAT
DV D
MENU
DISP
SETUP
Playing a Movie Disc (continued)
Next or Previous Chapter Selection:
To select the next chapter of the movie press the
button. To select the previous chapter press
the button.
ST OP
REPEAT
DV D
MENU
DISP
SETUP
Display Button:
Press the DISP button during movie play to display
the following information in this order for most discs:
Title Elapse, Title Remain, Chapter Elapse, Chapter
Remain and Display Off.
Subtitle Language:
P
ress the SUBTITLE
button during playback. Each
time the button is pressed, the subtitle language
changes. The selection of subtitle appears at the top
of the screen.
Notes:
1.
Some discs may contain only one subtitle language.
2. Depending on the disc, the number of subtitle
languages may be different.
DVD
MENU
DISP
SETUP
ENTER
PROGRAM
ENTER
PROGRAM
RETURN
TITL E
SUBTITLE
SD
US B
R/ L
A- B
ZOOM
Audio Language:
P
ress the R/L
button during playback. Each time the
button is pressed, the audio language changes. The
selection of audio appears at the top of the screen.
RETURN
TITL E
SUBTITLE
SD
US B
R/ L
A- B
ZOOM
Direct Chapter Selection:
To directly select a chapter use the numeric pad on
the remote control to enter the number of the chapter
you want to select. For example: If you want to go to
chapter 7 press the number 7 on the remote control
the unit will automatically switch to chapter 7.
1 2 3 4
5 6 7 8
9 0
+10
10
Playing a MP3 File
Inserting a Disc:
1. Press the power button to turn the unit on.
2. Insert a disc into the player with the label on the
disc facing upward.
3. The disc will automatically load and start playing.
Note: To remove the disc press the eject button.
Inserting a USB Drive:
1. Press the power button
to turn the unit on.
2. Insert a USB drive into the USB slot. Note: If the
USB drive does not fit, flip it over and try again.
3. The USB drive will automatically load and start
playing.
Note: To remove the USB drive pull the drive out
of the slot.
Inserting a USB Drive:
1. Press the power button to turn the unit on.
2. Insert a SD Card into the USB card slot with the
notch facing to the left until it clicks into place. Note:
If the SD card does not fit, flip it over and try again.
3. The SD card will automatically load and start
playing.
Note: To remove the SD card press on the card
until it clicks, then remove the card.
Playing a Movie Disc (continued)
Repeat Play Selection:
To record a section of the movie to play repeatedly
press the A-B button once, “Repeat A-” appears
on the screen. Press the A-B button again to con-
cluded your selection. The section of the movie
will play continually. Press the A-B button again to
cancel this feature.
Zoom Selection:
1.
P
ress the ZOOM
button during playback.
Each
time the button is pressed, the magnification
increment changes in the following order: 2X,
3X, 4X, 1/2, 1/3, 1/4 then Off.
2. Use the navigation buttons
, , and to
move the image on the screen.
RETURN
TITL E
SUBTITLE
SD
US B
R/ L
A- B
ZOOM
RETURN
TITL E
SUBTITLE
SD
US B
R/ L
A- B
ZOOM
L
a
b
e
l
F
ac
i
ng
U
p
Notch
11
Playing a MP3 File (continued)
MP3 Interface Screen:
The MP3 media (Disc, USB drive or SD card) con-
tains folder(s) with files inside the folders. These
files can include music tracks, photos and/or videos
(compatible MPEG1, MPEG2 and DivX files). Use
the icons at the bottom of the screen to select which
type of files you want to access.
Note: If an icon can not be select the unit has deter-
mine that kind of files is not accessible.
Mode Selection:
1. Select the DVD source by pressing the MODE
button until “DVD” appears on the screen.
2. Press the SD/USB button on the remote control.
A screen will appear with 3 selections: DISC,
CARD and USB.
3. Use the or
button on the remote control to
select the desired mode.
4.
Press the ENTER button to confirm your selection.
M
O
D
E
Folders
Files
Music
Photos Video
File Selection:
1.
Use the
, , and
buttons to navigate
both the folders and file menus.
2. When the correct file has been located press the
ENTER button on the remote control.
Pausing Play:
Press the pause button on the system pause
play. Press the button again to resume play. You
can also use the pause button on the remote
control
M
O
D
E
Stopping Play:
Press the button to pre-stop play. Press the
play button to resume play where the play was
stopped. Press the button twice to stop play
then press the play button to start play from the
beginning of the file.
Next or Previous File Selection:
To select the next file of the movie press the
button. To select the previous file press the
button.
DV D
MENU
DISP
SETUP
ENTER
PROGRAM
RETURN
TITL E
SUBTITLE
ST OP
REPEAT
DV D
MENU
DISP
SETUP
12
Playing a MP3 File (continued)
File Repeat Function:
Press the REPEAT button to select from the follow-
ing repeat functions:
REP 1 = Repeat one file continuously.
REP DIR = Repeat every file in the directory
continuously.
REP ALL = Continuously repeat every file.
REP OFF = Repeat function is off.
Direct File Selection:
To directly select a file use the numeric pad on the
remote control to enter the number of the file you
want to select. For example: If you want to go to file
7 press the number 7 on the remote control the unit
will automatically switch to file 7.
1 2 3 4
5 6 7 8
9 0
+10
9 0
+10
ST OP
REPEAT
Program Function:
1. Press the PROGRAM button on the remote control
to enter the programming screen.
2. Under the “T” column enter the folder number.
3. Under the “C” column enter the file number.
4. When you have finish programming your play list
use the navigation buttons , , and to
highlight the “PLAY” button at the bottom of the
screen. Then press the ENTER button to start your
programmed play list .
DV D
MENU
DISP
SETUP
ENTER
PROGRAM
RETURN
TITL E
SUBTITLE
Auxiliary Audio/Video Inputs
Internal Auxiliary RCA Inputs (AV1):
1. A device must be connected to the RCA connectors
coming from the MV1055.
2. Press the MODE button until “AV1” appears on the
screen.
3. Use the controls on the connected device to control
the playback.
3.5mm Auxiliary Input (AV2):
1. Plug in a device with a 3.5mm audio/video output
into the MV1055.
2. Press the MODE button until “AV2” appears on the
screen.
3. Use the controls on the connected device to control
the playback.
M
O
D
E
M
O
D
E
13
Dome Lights Operation
Dome Light Switch:
Press the dome light button to turn on and off
the dome lights in the MV1055.
M
O
D
E
Dome Light Door Switch:
When the vehicle’s door is open the dome light
comes on automatically. To turn off the dome
lights when the door is open press the dome light
door button to turn the dome lights off.
IR Repeater
The audio signal is converted to an infrared light
and transmitted to the headphones (purchased
separately). Refer to the owner’s manual included
with the headphone on how to adjust the volume to
suit the listener’s taste.
Note: For optimal performance a clear line of sight
is required between the MV1055 IR repeater and
the headphones.
Headphone Operation
IR Repeater
HP-400
Headphones
(Purchased
Separately)
Wiring
14
Wire Harness:
Red Wire: Connect the red wire to a +12 volt
power wire that is turned on and off by the position
of the ignition key.
Black Wire: Connect the black wire to the chassis
of the vehicle using a ring terminal and self-tapping
screw or bolt.
Audio/Video RCA Connectors:
Audio/Video Output: Connect to an external monitor.
Audio/Video Input: Connect to an external source,
for example a DVD player, video camera, video
game, etc.
Wire Leads:
Yellow Wire: Connect the yellow wire to a constant
+12 volt wire that is NOT turned on and off by the
position of the ignition key.
Black Wire [Negative Door Lock Trigger (-)]:
Connect the black wire to the common trigger wire
coming from all door pin switches.
Note: If the blue wire (positive door lock trigger) is
connected the black wire has no connection.
Blue Wire [Positive Door Lock Trigger (+)]:
Connect the blue wire to the common trigger wire
coming from all door pin switches.
Note: If the black wire (negaitve door lock trigger)
is connected the blue wire has no connection.
Green Wire (FM Transmitter Antenna): Do not
connect this wire. Lay this wire across the of the
roof making sure is does not come into contact
with any metal parts of the roof.
2A Fuse
Filter &
Fuse Box
Installation
15
1. Mount the Bracket:
Carefully plan exactly where to mount the bracket.
Also plan where the wires are going to run once the
bracket is mounted to the ceiling of the vehicle.
2. Mount the Main Unit:
Feed the wires through the opening in the bracket.
When attaching the main unit to the bracket with
the supplied screws make sure no wires or connec-
tors get trapped between the mounting bracket and
main unit.
Note: Damage may occur if connectors are force
up into the main unit.
3. Install the Trim Cover:
Snap the trim cover on to the main unit.
Bracket
Bracket
Mounting
Screws
(not supplied)
Main Unit
Main Unit
Screws
and Washers
(supplied)
Trim
Cover
Vehicle’s Roof
Supports
MV1055-UM Rev. C 10-3-15
© Copyright 2015 Magnadyne Corporation
ONE (1) YEAR LIMITED WARRANTY
Magnadyne Corporation or its authorized agents will within 1 year from the date of sale to you,
repair, replace or refund the retail sales price of said product or any part thereof, at the option of the
Magnadyne Corporation or its authorized agents, if said product or part is found defective in materi-
als or workmanship, when properly connected and operating on the correct power requirements
designated for the specific product. This warranty and Magnadyne Corporation or its authorized
agents obligations hereunder do not apply where the product was; damaged while in the posses-
sion of the consumer, subjected to unreasonable or This warranty does not cover the cabinet
appearance items or accessories used in connection with this product, or any damage to recording
or recording tape, or any damage to the products resulting from improper installation, alteration,
accident, misuse, abuse or acts of nature.
MAGNADYNE CORPORATION OR ITS AUTHORIZED AGENTS SHALL NOT BE LIABLE
TO ANYONE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OR CLAIMS EXCEPT
THOSE ACCORDED BY LAW. NO EXPRESSED WARRANTY OR IMPLIED WARRANTY
IS GIVEN EXCEPT THOSE SET FORTH HEREIN. NO IMPLIED WARRANTY SHALL EXTEND
BEYOND 1 YEAR FROM THE DATE OF SALE.
This warranty extends only to the original purchaser of the product and is not transferable.
Some states do not allow limitations on how long an implied warranty lasts and some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitations
or exclusion may not apply to you. This warranty gives you specific legal rights and you may have
other rights that vary from state to state.
Defective merchandise should be returned to the original point of purchase or secondly, to
Magnadyne Corporation, 1111 W. Victoria Street, Compton CA 90220. Return Authorization must
be obtained before sending, or merchandise may be refused.
Warranty
/
