CMA Dishmachines EST-44 Quick Installation Guide

EST-44
CMA Dishmachines
Brand
CMA Dishmachines
Model
EST-44
Category
Dishwashers
Type
Quick Installation Guide

This manual is also suitable for

HOT WATER
SUPPLY LINE
1/2" INLET
EST44
REAR VIEW
11-2016
EST-44/66
Quick Setup
Instructions
Connect Hot Water Supply Line to 1/2"Final Rinse
Water Inlet. S E E STE P 11 .
Connect Fill Water Supply Line (120F/140F) to a 1/2"water
inlet to fill the machine.
Connect d r ain at eith e r e n d of th e h or iz o n tal
d r ain pipe f r o m wa sh tank or sc rap trap drain.
3 Phase: Connect the wire with the highest voltage
(stinger lead) to L2 on the contactor. L1, L2 and L3
must comply with all local and state electrical codes
for sizing of wire and circuit breaker protection.
Additional information can be found in the
Installation and Operation manual supplied with
machine.
Remove plug to install detergent fitting. Remove plugs from
the mixing chamber to install sani/rinse injection fitting
(sanitizer, detergent and rinse injection fittings provided by
dispenser manufacturer, CMA does not supply.)
WARNING: Electrical and plumbing
connections need to be made by a
licensed service person and comply
with all Federal, State and Local
Health, Electrical, Plumbing and
Safety codes.
1
STE P
4
STE P
2" HOLE
PLUG
3
STE P
VOLTS PHASE AMPS
208 1 76
240 1 84
208 3 50
240 3 54
HEATER 10kW
5
STE P
REMOVE
PLUG AND
INSTALL
DETERGENT
FITTING
PLUGS
ELECTRICAL
CONNECTION
3
2
1/2" FILL
WATER INLET
1/2" FINAL RINSE
WATER INLET
1
DETERGENT
FITTING INLET
5
MIXING
CHAMBER
5
SCRAP
TRAP DRAIN
4
DRAIN PLUMBING
NOT SUPPLIED
OPTIONAL VENT
HOODS 4"X16"
2" HOLE
PLUG
DRAIN PIPE
4
2
STE P
FILL WATER
SUPPLY LINE
FILL WATER
SUPPLY LINE
1/2" INLET
ELECTRICAL
HARD WIRE
CONNECTION
POINT
PN: 10130.21
STEP
11
Switch Manual/Auto switch to Manual Mode.
Adjust Pressure Regulator Valve to 20 PSI.
If E-Temp is installed on machine, press rinse
switch to fill E-Temp tank. Return Manual/Auto
switch to Auto Mode.
PRESSURE REGULATOR
LOCATED BEHIND
CONTROL BOX
ON-OFF
ON-OFF
Adjust thermostat if necessary. Water temperature
should be 140F rinse and 140F wash for EST44L.
The EST44H should read 180F rinse 155F wash.
EST44 FRONT VIEW
11-2016
Tu r n on dish m achine by pressing t h e " POW E R
ON/OFF"switch to the "ON"position. Dishmachine
will fill automatically and will also activate heater.
Close drain valve before filling machine with water.
9
STEP
C
L
O
S
E
Remove the stainless steel plug to install the detergent
probe (provided by dispenser manufacturer, CMA does
not supply).
7
STEP
Remove motor cap to verify motor rotation. Shaft slot
should be rotating clock-wise when motor is running. If
shaft slot is turning counter clock wise, swap L-1 and L-3
on main contactor.
EST-44/66
Quick Setup
Instructions
WARNING
: Electrical and plumbing
connections need to be made by a
licensed service person and comply
with all Federal, State and Local
Health, Electrical, Plumbing and
Safety codes.
10
STEP
6
STEP
8
STEP
RINSE
WASH
*PRESSURE REGULATOR LOCATED
BEHIND CONTROL BOX
AUTO/MANUAL
SWITCH
AUTO/MANUAL
SWITCH
RINSE TEMP
WASH TEMP
RINSE TEMP
WASH TEMP
ON-OFF
AUTO/MANUAL
SWITCH
RINSE TEMP
WASH TEMP
GAUGE
POWER
ON/OFF
10
DETERGENT
PROBE INLET
STAINLESS STEEL
SCRAP TRAP
TEMPERATURE
GAUGES
WASH
THERMOSTAT
MANUAL AUTO
SWITCH
11
11
e-TEMP
6
8
RINSE PRESSURE
11
* PRESSURE
REGULATOR
PRESSURE
GAUGE
11
RINSE
THERMOSTAT
8
MOTOR CAP
7
DOOR SAFETY SWITCH
DRAIN VALVES
9
The Spirit of Excellence
an Ali Group Company
  • Page 1 1
  • Page 2 2

CMA Dishmachines EST-44 Quick Installation Guide

EST-44
CMA Dishmachines
Brand
CMA Dishmachines
Model
EST-44
Category
Dishwashers
Type
Quick Installation Guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents