Sony VPL-CS1 SuperLite User manual

Operating Instructions

Mode d’emploi

Manual de instrucciones

VPL-CS1

4-074-278-11 (1)

C:\MUN\Data\FM\VPL-CS1\VPL-

CS1.nouhindata\407427811VPLCS1WW\01COV-

VPLCS1WW\01COV.fm

masterpage:Left

4-074-278-

11

(1)

LCD Data Projector

GB

FR

ES

VPL-CS1

4-074-278-11 (1)

C:\MUN\Data\FM\VPL-CS1\VPL-

CS1.nouhindata\407427811VPLCS1WW\02GB-

VPLCS1WW\02REG.fm

masterpage:Left

GB

2

WARNING

To prevent fire or shock hazard, do

not expose the unit to rain or

moisture.

To avoid electrical shock, do not

open the cabinet. Refer servicing to

qualified personnel only.

For the customers in the USA

Declaration of Conformity

Trade Name: SONY

Model No.: VPL-CS1

Responsible Party: Sony Electronics Inc.

Address: 1 Sony Drive, Park Ridge,

NJ.07656 USA

Telephone No.: 201-930-6970

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) This device

may not cause harmful interference, and (2)

this device must accept any interference

received, including interference that may

cause undesired operation.

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there is

no guarantee that interference will not occur

in a particular installation. If this equipment

does cause harmful interference to radio or

television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct

the interference by one or more of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the

equipment and receiver.

- Connect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/

TV technician for help.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

For the customers in Canada

This Class B digital apparatus complies with

Canadian ICES-003.

This symbol is intended to

alert the user to the presence

of uninsulated “dangerous

voltage” within the

product’s enclosure that may

be of sufficient magnitude to

constitute a risk of electric

shock to persons.

This symbol is intended to

alert the user to the presence

of important operating and

maintenance (servicing)

instructions in the literature

accompanying the

appliance.

VPL-CS1

4-074-278-11 (1)

C:\MUN\Data\FM\VPL-CS1\VPL-

CS1.nouhindata\407427811VPLCS1WW\02GB-

VPLCS1WW\02REG.fm

masterpage:Left

3

GB

For the customers in the United

Kingdom

WARNING

THIS APPARATUS MUST BE

EARTHED

IMPORTANT

The wires in this mains lead are coloured in

accordance with the following code:

Green-and-Yellow: Earth

Blue: Neutral

Brown: Live

As the colours of the wires in the mains lead

of this apparatus may not correspond with

the coloured markings identifying the

terminals in your plug proceed as follows:

The wire which is coloured green-and-

yellow must be connected to the terminal in

the plug which is marked by the letter E or

by the safety earth symbol I or coloured

green or green-and-yellow.

The wire which is coloured blue must be

connected to the terminal which is marked

with the letter N or coloured black. The wire

which is coloured brown must be connected

to the terminal which is marked with the

letter L or coloured red.

Voor de klanten in Nederland

Bij dit product zijn batterijen

geleverd. Wanneer deze leeg

zijn, moet u ze niet

weggooien maar inleveren

als KCA.

The socket-outlet should be installed near

the equipment and be easily accessible.

VPL-CS1

4-074-278-11 (1)

C:\MUN\Data\FM\VPL-CS1\VPL-

CS1.nouhindata\407427811VPLCS1WW\02GB-

VPLCS1WW\02REG.fm

masterpage:Left

GB

4

VPL-CS1

4-074-278-11 (1)

C:\MUN\Data\FM\VPL-CS1\VPL-

CS1.nouhindata\407427811VPLCS1WW\02GB-

VPLCS1WW\01COVTOC.fm

masterpage:Left

5

GB

Table of Contents

GB

Overview

Precautions .........................................6

Features ..............................................7

Location and Function of Controls ...8

Front/Left Side/Bottom ................8

Rear/Right Side ............................8

Control Panel ..............................10

Connector Panel .........................11

Remote Commander ...................12

Setting Up and Projecting

Installing the Projector .....................14

Connecting the Projector ..................15

Connecting with a Computer ......15

Connecting with a VCR or 15k

RGB/Component

Equipment .......................17

Selecting the Menu Language ..........19

Projecting .........................................21

Adjustments and Settings

Using the Menu

Using the MENU .............................24

The PICTURE CTRL Menu ............25

The INPUT SETTING Menu ...........26

The SET SETTING Menu ...............27

Maintenance

Maintenance .....................................29

Replacing the Lamp ....................29

Cleaning the Air Filter ................30

Troubleshooting ............................... 31

Warning Messages ..................... 33

Caution Messages ...................... 33

Other

Notes on Installation ........................ 34

Unsuitable Installation ............... 34

Unsuitable Conditions ................ 34

Specifications .................................. 35

Index ............................................... 41

VPL-CS1

4-074-278-11 (1)

C:\MUN\Data\FM\VPL-CS1\VPL-

CS1.nouhindata\407427811VPLCS1WW\02GB-

VPLCS1WW\03OVR.fm

masterpage:Left

GB

6

Precautions

B

Overview

Precautions

On safety

• Check that the operating voltage of your

unit is identical with the voltage of your

local power supply.

• Should any liquid or solid object fall into

the cabinet, unplug the unit and have it

checked by qualified personnel before

operating it further.

• Unplug the unit from the wall outlet if it is

not to be used for several days.

• To disconnect the cord, pull it out by the

plug. Never pull the cord itself.

• The wall outlet should be near the unit and

easily accessible.

• The unit is not disconnected to the AC

power source (mains) as long as it is

connected to the wall outlet, even if the

unit itself has been turned off.

• Do not look into the lens while the lamp is

on.

• Do not place your hand or objects near the

ventilation holes. The air coming out is

hot.

• Be careful not to catch your fingers by the

adjuster when you lift up the projector. Do

not push hard on the top of the projector

with the adjuster out.

On illumination

• To obtain the best picture, the front of the

screen should not be exposed to direct

lighting or sunlight.

• Ceiling-mounted spot lighting is

recommended. Use a cover over

fluorescent lamps to avoid lowering the

contrast ratio.

• Cover any windows that face the screen

with opaque draperies.

• It is desirable to install the projector in a

room where floor and walls are not of

light-reflecting material. If the floor and

walls are of reflecting material, it is

recommended that the carpet and wall

paper be changed to a dark color.

On preventing internal heat build-

up

After you turn off the power with the

I

/ 1

key, do not disconnect the unit from the wall

outlet while the cooling fan is still running.

Caution

The projector is equipped with ventilation

holes (intake) on the bottom side and

ventilation holes (exhaust) on left and rear.

Do not block or place anything near these

holes, or internal heat build-up may occur,

causing picture degradation or damage to the

projector.

On cleaning

• To keep the cabinet looking new,

periodically clean it with a soft cloth.

Stubborn stains may be removed with a

cloth lightly dampened with a mild

detergent solution. Never use strong

solvents, such as thinner, benzene, or

abrasive cleansers, since these will

damage the cabinet.

• Avoid touching the lens. To remove dust

on the lens, use a soft dry cloth. Do not use

a damp cloth, detergent solution, or

thinner.

• Clean the filter at regular intervals.

On repacking

• Save the original shipping carton and

packing material; they will come in handy

if you ever have to ship your unit. For

maximum protection, repack your unit as

it was originally packed at the factory.

VPL-CS1

4-074-278-11 (1)

C:\MUN\Data\FM\VPL-CS1\VPL-

CS1.nouhindata\407427811VPLCS1WW\02GB-

VPLCS1WW\03OVR.fm

masterpage:Left

7

GB

Features

Overview

Features

High portability

• Light weight/small size

This projector has been miniaturized to

approx. 2.9 kg (6 lb 6 oz) in weight and

B5-file size through the adoption of a new

retractable mechanism. A carrying handle

and a removable strap are equipped with

the projector, so you can carry it easily

with your computer.

Reduced noise

Because the projector uses a new cooling

mechanism, noise has been reduced.

High brightness, high picture

quality

• High brightness

Adopting the new developed optical

system and the 120 W UHP lamp allows

high brightness (light output 600 ANSI

lumen) and excellent uniformity on the

picture.

• High resolution

Three 0.7-inch, about 480,000 pixel

SVGA panels provide a resolution of 800

× 600 dots for RGB input and 600

horizontal TV lines for video input.

Simple setup, easy presentation

• Simple setup with external equipment

This projector is preset for 37 kinds of

input signals. You can project images from

an external signal source just by

connecting the equipment with the

supplied cable and pushing the APA key.

• Simple Remote Commander with

mouse control functions

You can operate a computer with the

Remote Commander since the unit has a

build-in mouse receiver.

Compatible with USB (Universal

Serial Bus) hub function

You can connect the projector to USB

equipment, such as a USB mouse, and

control the projector by using the supplied

application software from a computer.

1)

Using this application software, you can

open a file you want to use for your

presentation with the supplied Remote

Commander.

Accepts various input signals

• Scan converter loaded

This projector has a build-in scan

converter that converts the input signal

within 800 × 600 dots.

• Compatible input signals

This projector accepts video signals of

composite, S video, and component as

well as 15k RGB, VGA, SVGA, XGA,

and SXGA signals, which all can be

displayed.

• Compatible with six color systems

NTSC, PAL, SECAM, NTSC

4.43

2)

, PAL-

M, or PAL-N color system can be selected

automatically or manually.

......................................................................

• Windows is a registered trademark of

Microsoft Corporation in the United States

and/or other countries.

• VGA, SVGA, XGA, and SXGA are

registered trademarks of the International

Business Machines Corporation, U.S.A.

• Macintosh is a registered trademark of

Apple Computer, Inc.

• IBM PC/AT is a registered trademark of

International Business Machines

Corporation, U.S.A.

• VESA is a registered trademark of Video

Electronics Standard Association.

• Display Data Channel is a trademark of

Video Electronics Standard Association.

• PC-98 is a trademark of NEC Corporation.

1)The supplied application software and the

USB hub function of this projector are

compatible with Windows 98 preinstall

model.

2)NTSC

4.43

is the color system used when

playing back a video recorded on NTSC

on a NTSC

4.43

system VCR.

VPL-CS1

4-074-278-11 (1)

C:\MUN\Data\FM\VPL-CS1\VPL-

CS1.nouhindata\407427811VPLCS1WW\02GB-

VPLCS1WW\03OVR.fm

masterpage:Left

GB

8

Location and Function of Controls

Location and

Function of Controls

1

Lock button

2

Front cover

Slide the lock button to open the front

cover. The leg on the bottom of the

projector opens. When projecting the

picture, place the projector on a flat

surface with the leg open.

3

Carrying handle

Pull up the handle from the projector for

carrying.

4

Zoom ring

Adjusts the picture size.

5

Focus ring

Adjusts the picture focus.

6

Front remote control detector

(SIRCS receiver)

7

Lens

8

AC IN socket

Connects the supplied AC power cord.

9

Ventilation holes (intake)/air

filter cover (bottom)

• Do not place anything near the

ventilation holes as it may cause internal

heat build-up.

• Do not place your hand or objects near

the ventilation holes as it may cause the

air coming out heat build-up.

• To maintain optimal performance,

clean

the air filter every 300 hours.

q;

q;q;

q;

Lamp cover (bottom)

qa

qaqa

qa

Ventilation holes (exhaust)

qs

qsqs

qs

Control panel

For details, see “Control Panel” on

page 10.

qd

qdqd

qd

Shoulder strap holder

Front/Left Side/Bottom

Rear/Right Side

Notes

VPL-CS1

4-074-278-11 (1)

C:\MUN\Data\FM\VPL-CS1\VPL-

CS1.nouhindata\407427811VPLCS1WW\02GB-

VPLCS1WW\03OVR.fm

masterpage:Left

9

GB

Location and Function of Controls

Overview

qf

qfqf

qf

Security lock

Connects to an optional security cable

(Kensington’s).

qg

qgqg

qg

Speaker

qh

qhqh

qh

Rear remote control detector

(SIRCS receiver)

qj

qjqj

qj

Leg

qk

qkqk

qk

Connector panel

For details, see “Connector Panel” on

page 11.

ql

qlql

ql

Ventilation holes (intake)

The security lock corresponds to

Kensington’s MicroSaver Security

System.

If you have any comment, contact:

Kensington

2853 Campus Drive

San Mates, CA 94403

U.S.A.

Tel: 800-535-4242: extension

3348

Home page address:

http://www.kensington.com/

VPL-CS1

4-074-278-11 (1)

C:\MUN\Data\FM\VPL-CS1\VPL-

CS1.nouhindata\407427811VPLCS1WW\02GB-

VPLCS1WW\03OVR.fm

masterpage:Left

GB

10

Location and Function of Controls

1

I /

1

11

1

(on/standby) key

Turns on and off the projector when the

projector is in standby mode. The ON/

STANDBY indicator lights in green

when the power is turned on.

When turning off the power, press

the

I /

1 key twice following the

message on the screen, or press and hold

the key for about one second.

For details on steps for turning off the

power, see “To turn off the power” on

page 23.

2

INPUT key

Selects the input signal. Each time you

press the key, the input signal switches

between video input and INPUT A

connector.

3

APA (Auto Pixel Alignment) key

Adjusts a picture clearest automatically

while a signal is input from a computer.

4

VOLUME +/– keys

Adjust the volume of the built-in

speakers.

+ : Increases the volume.

–

:

Decreases the volume.

5

Indicators

• LAMP/COVER: Lights up or flashes

under the following conditions:

– Lights up when the lamp has

reached the end of its life or

becomes a high temperature.

– Flashes when the lamp cover or air

filter cover is not secured firmly.

• FAN/TEMP (Temperature): Lights

up or flashes under the following

conditions:

– Lights up when temperature inside

the projector becomes unusually

high.

– Flashes when the fan is broken.

• POWER SAVING: Lights up when

the projector is in power saving mode.

When POWER SAVING in the SET

SETTING menu is set to ON, the

projector goes into power saving mode

if no signal is input for 10 minutes.

Although the lamp goes out, the

cooling fan keeps running. In power

saving mode, any key does not

function for the first 30 seconds. The

power saving mode is canceled when a

signal is input or any key is pressed.

• ON/STANDBY: Lights up or flashes

under the following conditions:

– Lights in red when a AC power cord

is plugged into a wall outlet. Once in

standby mode, you can turn on the

projector with the

I

/ 1 key.

– Lights in green when the power is

turned on.

– Flashes in green while the cooling

fan runs after the power is turned off

with the

I

/ 1 key. The fan runs for

about 90 seconds after the power is

turned off.

The ON/STANDBY indicator

flashes quickly for the first 30

seconds. During this time, you

cannot turn the power back on with

the

I

/ 1 key.

For details on the LAMP/COVER and

the FAN/TEMP indicators, see page 32.

Control Panel

RESET MENU

POWER

INPUT

APA

VOLUME

POWER SAVING

ON/STANDBY

F

A

N

/T

E

M

P

LAMP/COVER

ENTER

+

–

VPL-CS1

4-074-278-11 (1)

C:\MUN\Data\FM\VPL-CS1\VPL-

CS1.nouhindata\407427811VPLCS1WW\02GB-

VPLCS1WW\03OVR.fm

masterpage:Left

11

GB

Location and Function of Controls

Overview

6

ENTER key

Enters the settings of items in the menu

system.

7

Arrow keys (

M

MM

M

/

m

mm

m

/

<

<<

<

/

,

,,

,

)

Select the menu or to make various

adjustments.

8

RESET key

Resets the value of an item back to its

factory preset value. This key functions

when the menu or a setting item is

displayed on the screen.

9

MENU key

Displays the on-screen menu. Press

again to clear the menu.

1

INPUT A connector (HD D-sub

15-pin, female)

Connect to external equipment such as a

computer.

Connects to the monitor output on a

computer using the supplied cable.

When inputting a component or 15k

RGB signal, use an optional cable.

2

Video input connector

Connect to external video equipment

such as a VCR.

• S VIDEO (mini DIN 4-pin):

Connects to the S video output (Y/C

video output) of video equipment.

• VIDEO (phono type): Connects to

the composite video output of video

equipment.

If you connect video equipment to both the

S VIDEO and VIDEO jacks, the signal

from the S VIDEO jack is selected. When

projecting the picture via the VIDEO jack,

be sure not to connect a cable to the S

VIDEO jack.

3

MOUSE connector (6-pin)

Connects to the PS/2 mouse port on a

computer via the supplied mouse cable,

to control the mouse function of the

connected computer.

4

USB connector (USB A-plug for

downstream, 4-pin)

Connect to USB equipment such as a

mouse, camera, etc.

5

USB connector (USB B-plug for

upstream, 4-pin)

Connect to the USB connector on a

computer. When you connect the

projector to the computer, the projector

recognizes the mouse of the computer

connected to the INPUT A connector

and you can control the mouse function

with the supplied Remote Commander.

The supplied application software can

be installed in the computer attached to

this connector.

6

AUDIO (stereo minijack)

connector

When listening to sound output from the

computer, connect to the audio output of

the computer.

When listening to sound output from the

VCR, connect to the audio output of the

VCR.

This connector functions as the audio

input of the INPUT A, VIDEO and S

VIDEO connectors.

Connector Panel

INPUT AS VIDEOVIDEOMOUSEAUDIO

Rear side

Note

VPL-CS1

4-074-278-11 (1)

C:\MUN\Data\FM\VPL-CS1\VPL-

CS1.nouhindata\407427811VPLCS1WW\02GB-

VPLCS1WW\03OVR.fm

masterpage:Left

GB

12

Location and Function of Controls

The keys that have the same names as those

on the control panel function identically.

You can control a connected computer using

the Remote Commander.

For details, see “To control the computer

using the supplied Remote Commander” on

page 22.

1

I /

1

11

1

key

2

INPUT key

3

FUNCTION 1, 2 keys

When you have saved a file in the

FUNCTION 1 or 2 key using the

supplied application software, you can

open the file with a press of the

corresponding key.

For details, see the README file and

the HELP file supplied with the

application software.

4

L CLICK key

Functions as the left button on a mouse.

5

R CLICK key

Functions as the right button on a mouse.

6

Joystick

Functions as the mouse of the computer

connected to the unit.

7

Infrared transmitter

To install batteries

1

Push and slide to open the lid, then

install the two size AAA (R03)

batteries (supplied) with the correct

polarity.

2

Replace the lid.

Remote Commander

INPUT

R. CLICK

FUNCTION

1

2

Be sure to install

the battery from

the

#

side.

VPL-CS1

4-074-278-11 (1)

C:\MUN\Data\FM\VPL-CS1\VPL-

CS1.nouhindata\407427811VPLCS1WW\02GB-

VPLCS1WW\03OVR.fm

masterpage:Left

13

GB

Location and Function of Controls

Overview

Notes on batteries

• Make sure that the battery orientation is

correct when inserting batteries.

• Do not mix an old battery with a new one

or different types of batteries.

• If you do not use the Remote Commander

for a long time, remove the batteries to

avoid damage from battery leakage. If

batteries have leaked, remove them, wipe

and dry the battery compartment, and

replace the batteries with new ones.

Notes on Remote Commander

operation

• Make sure that nothing obstructs the

infrared beam between the Remote

Commander and the remote control

detector on the projector. Direct the

Remote Commander toward the front or

rear remote control detector.

• The operation range is limited. The shorter

the distance between the Remote

Commander and the projector is, the wider

the angle within which the commander can

control the projector becomes.

VPL-CS1

4-074-278-11 (1)

C:\MUN\Data\FM\VPL-CS1\VPL-

CS1.nouhindata\407427811VPLCS1WW\02GB-

VPLCS1WW\04SET.fm

masterpage:Left

GB

14

Installing the Projector

B

Setting Up and Projecting

Installing the Projector

This section describes how to install the projector.

The distance between the lens and the screen varies depending on the size of

the screen. Use the following table as a guide.

You can not install the projector upside down, such as on a ceiling.

Unit: m (feet)

Screen size

(inches)

40 60 80 100 120 150

Minimum

Distance

1.6

(5.2)

2.4

(7.8)

3.2

(10.5)

4.0

(13.2)

4.9

(15.9)

6.1

(20.0)

Maximum

Distance

2.0

(6.6)

3.1

(10.0)

4.1

(13.5)

5.2

(16.9)

6.2

(20.3)

7.8

(25.5)

Note

Distance between the screen and

the center of the lens

VPL-CS1

4-074-278-11 (1)

C:\MUN\Data\FM\VPL-CS1\VPL-

CS1.nouhindata\407427811VPLCS1WW\02GB-

VPLCS1WW\04SET.fm

masterpage:Left

15

GB

Connecting the Projector

Setting Up and Projecting

Connecting the Projector

When making connections, be sure to do the following:

• Turn off all equipment before making any connections.

• Use the proper cables for each connection.

• Insert the cable plugs properly; plugs that are not fully inserted often

generate noise. When pulling out a cable, be sure to pull it out from the plug,

not the cable itself.

Supplied mouse cables may not work properly according to your computer.

This section describes how to connect the projector to a computer.

For more information, refer to the computer’s instruction manual.

• The projector accepts VGA, SVGA, XGA, and SXGA signals. However, we

recommend that you set the output mode of your computer to SVGA mode for the

external monitor.

• If you set your computer, such as a notebook type, to output the signal to both your

computer’s display and the external monitor, the picture of the external monitor may

not appear properly. Set your computer to output the signal to only the external

monitor.

For details, refer to the computer’s operating instructions supplied with your

computer.

• Supplied mouse cables may not work properly according to your computer.

• This projector is compatible with a DDC2B (Digital Data Channel 2B). If your

computer is compatible with a DDC, turn the projector on according to the following

procedures.

1

Connect the projector to the computer by using the supplied HD D-sub 15 pin cable.

2

Turn the projector on.

3

Start the computer.

Note

Connecting with a Computer

Notes

VPL-CS1

4-074-278-11 (1)

C:\MUN\Data\FM\VPL-CS1\VPL-

CS1.nouhindata\407427811VPLCS1WW\02GB-

VPLCS1WW\04SET.fm

masterpage:Left

GB

16

Connecting the Projector

To connect an IBM PC/AT compatible computer

When you use a USB mouse and USB equipment

• When you use the supplied application software, connect your computer

as illustrated above. This application software and the USB hub function

can be used on a computer loaded with Windows 98 preinstall model.

• As the projector recognizes the USB mouse when the computer is

connected to the USB connector, do not connect anything to the PS/2

mouse port.

• Your computer may not start correctly when it has been connected to the

USB connector on the projector via the USB cable. In this case, first

disconnect the USB cable, restart the computer, then connect the

computer to the projector using the USB cable supplied with the

projector.

On the USB hub function

When connecting the projector to a computer by using the USB cable for the

first time, the computer recognizes the following devices automatically.

1

USB hub (general use)

2

USB human interface device (wireless mouse function)

3

USB human interface device (projector control function)

Excepting these devices above mentioned, the computer recognizes the device

connected to the downstream connector on the projector.

Notes

INPUT AS VIDEOVIDEOMOUSEAUDIO

Rear side

USB equipment

USB cable A type – B type (supplied)

Stereo audio connecting cable (not supplied)

HD D-sub

15-pin cable

(supplied)

to USB connector

to monitor output

to audio output

Computer

VPL-CS1

4-074-278-11 (1)

C:\MUN\Data\FM\VPL-CS1\VPL-

CS1.nouhindata\407427811VPLCS1WW\02GB-

VPLCS1WW\04SET.fm

masterpage:Left

17

GB

Connecting the Projector

Setting Up and Projecting

When you use a PS/2 mouse port

To connect a Macintosh computer

Use an ADP-20 signal adapter (not supplied). In this case, however, you can

not control the mouse of the computer by the Remote Commander.

This section describes how to connect the projector to a VCR and 15k RGB/

component equipment.

For more information, refer to the instruction manuals of the equipment you

are connecting.

To connect a VCR

1)

When both the S VIDEO and VIDEO jacks are connected to the external equipment,

the input signal from the S VIDEO jack is selected.

Connecting with a VCR or 15k RGB/Component Equipment

INPUT AS VIDEOVIDEOMOUSEAUDIO

to audio output

Rear side

HD D-sub

15-pin cable

(supplied)

to mouse port (PS/2)

PS/2 Mouse cable (supplied)

Stereo audio connecting cable (not supplied)

to monitor output

Computer

INPUT AS VIDEOVIDEOMOUSEAUDIO

Video cable (not supplied)

Stereo audio

connecting

cable (not

supplied)

S-Video cable (not supplied)

VCR

to video

output

1)

to S video

output

1)

Rear side

to audio

output

VPL-CS1

4-074-278-11 (1)

C:\MUN\Data\FM\VPL-CS1\VPL-

CS1.nouhindata\407427811VPLCS1WW\02GB-

VPLCS1WW\04SET.fm

masterpage:Left

GB

18

Connecting the Projector

To connect a 15k RGB/Component equipment

•S

et the aspect ratio using ASPECT in the INPUT SETTING menu

according to the input signal.

• When

you connect the unit to 15k RGB/component video equipment,

select RGB or component with the INPUT-A setting in the SET

SETTING menu.

•U

se the composite sync signal when you input the external sync signal

from 15k RGB/component equipment.

Notes

INPUT AS VIDEOVIDEOMOUSEAUDIO

Rear side

Stereo audio

connecting

cable (not

supplied)

SMF-402 Signal Cable (not supplied)

3

×

phono jack

↔

HD D-sub 15-pin (male)

to audio

output

15k RGB/Component equipment

to RGB/

component

output

VPL-CS1

4-074-278-11 (1)

C:\MUN\Data\FM\VPL-CS1\VPL-

CS1.nouhindata\407427811VPLCS1WW\02GB-

VPLCS1WW\04SET.fm

masterpage:Left

19

GB

Selecting the Menu Language

Setting Up and Projecting

Selecting the Menu Language

You can select one of seven languages for displaying the menu and other on-

screen displays. The factory setting is English.

1

Open the front cover, then plug the AC power cord into a wall outlet.

2

Press the

I

/

1

key to turn on the projector.

3

Press the MENU key.

The menu appears.

The menu presently selected is shown as a yellow button.

1

RESET MENU

POWER

INPUT

APA

VOLUME

POWER SAVING

ON/STANDBY

F

A

N

/T

E

M

P

LAMP/COVER

ENTER

3

2

4,5,6

+

–

80

50

PICTURE CTRL

CONTRAST:

BRIGHT:

GAMMA MODE: GRAPHICS

COLOR TEMP: HIGH

INPUT-A

VPL-CS1

4-074-278-11 (1)

C:\MUN\Data\FM\VPL-CS1\VPL-

CS1.nouhindata\407427811VPLCS1WW\02GB-

VPLCS1WW\04SET.fm

masterpage:Left

GB

20

Selecting the Menu Language

4

Press the

M

or

m

key to select the SET SETTING menu, then press the

,

or ENTER key.

The selected menu appears.

5

Press the

M

or

m

key to select “LANGUAGE,” then press the

,

or

ENTER key.

6

Press the

M

or

m

key to select a language, then press the

<

or ENTER

key.

The menu changes to the selected language.

To clear the menu

Press the MENU key.

The menu disappears automatically if a key is not pressed for one minute.

SET SETTING

STATUS: ON

INPUT-A: RGB

KEYSTONE MEMORY:

OFF

DIGITAL KEYSTONE:

OFF

LANGUAGE: ENGLISH

POWER SAVING

: OFF

SIRCS RECEIVER:

FRONT&REAR

LAMP TIMER:

00010h

INPUT-A

SET SETTING

STATUS: ON

INPUT-A: RGB

KEYSTONE MEMORY:

OFF

DIGITAL KEYSTONE:

OFF

LANGUAGE: ENGLISH

POWER SAVING

: OFF

SIRCS RECEIVER:

FRONT&REAR

LAMP TIMER:

00010h

INPUT-A

Page is loading ...

Sony VPL-CS1 SuperLite User manual

This manual is also suitable for

Sony VPL-CS1 SuperLite User manual

in other languages

Related papers

Other documents