DUE7242WCR2XXYC

Jacuzzi DUE7242WCR2XXYC User manual

Hello! I am an AI chatbot trained to assist you with the Jacuzzi DUE7242WCR2XXYC User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!

OPERATING MANUAL

Jacuzzi Luxury Bath

14525 Monte Vista Avenue

Chino, CA 91710

1-800-288-4002

www.jacuzzi.com

Pure Air

®

Whirlpool

Salon

®

Spa

LG74000D 06/2019

Operating Manual

English

Page 2 www.jacuzzi.com

General Operation Information. ....................................................................................................................................... 2

Reference Illustration for a Pure Air

®

System. ................................................................................................................. 3

Pure Air

®

Operations. ...................................................................................................................................................... 4

Pure Air

®

Auto-Dri™ Air Channels. .................................................................................................................................. 5

Whirlpool System Reference Illustrations. .................................................................................................................... 6-7

Whirlpool Operations. ................................................................................................................................................... 8-9

Heated Soak Reference Illustrations ........................................................................................................................ 10-11

RapidHeat™. ................................................................................................................................................................. 12

Cleaning. ....................................................................................................................................................................... 13

Maintenance. ............................................................................................................................................................ 13-14

Salon

®

Spa System Reference Illustrations .................................................................................................................. 15

Salon

®

Spa Operations. ................................................................................................................................................ 16

Troubleshooting Procedures. ........................................................................................................................................ 17

*For Spanish and French installation instructions, please visit www.jacuzzi.com/baths/support/owners-manuals/.

*Para instrucciones de instalación en español, por favor visite www.jacuzzi.com/baths/support/owners-manuals/.

*Pour directives d'installation en français canadien, veuillez visiter www.jacuzzi.com/baths/support/owners-manuals/.

Table of Contents

General Operation Information

All bathtubs manufactured by Jacuzzi Luxury Bath are designed for “ll and drain,” which means the bathtub should be

drained after each use and lled with fresh water by the next bather. This is a health precaution, as these bathtubs are

not designed to hold water continuously like pools or spas.

Close the drain and ll the bathtub until water is at least 1" to 2" (25 mm to 51 mm) above the highest jet or air inlet (see

water line indicated in the illustration - Figure 1). Do not turn on the Whirlpool or Pure Air

®

system at any time if the jets or

air inlets are not completely immersed in water. Running the Whirlpool or Pure Air

®

system when there is insufcient water

in the bathtub could result in water spraying outside the bath area.

ATTENTION: When exiting the bathtub, the water level will drop below the jets which could result in water being

sprayed out of the unit. To prevent this, you must turn unit OFF before exiting bathtub.

Fill to at least 1" to 2"

above highest jet

Fig. 1

Operating Manual

English

www.jacuzzi.com Page 3

Reference Illustration for a Pure Air

®

System

These illustrations are for reference only, as the unit comes fully assembled.

DANGER: RISK OF ELECTRIC SHOCK! Before servicing these connections, disconnect all

power supply cables to both 120 VAC services.

J2 Control Panel Pure Air

®

Schematic Diagram

J4 Control Panel Pure Air

®

Schematic Diagram

Fig. 2

CONTROL

PANEL

BLOWER

120 VAC 15A

Dedicated GFCI

Circuit Required

Fig. 3

BLOWER

CONTROL PANEL

CHROMATHERAPY

LIGHTS 2X

Auto-Dri™

SENSOR

CABLE

LIGHT CONTROL

BOX

120 VAC

Panel

LED Light

120VAC 15A

Dedicated GFCI

Circuit Required

120VAC 15A

Dedicated GFCI

Circuit Required

Operating Manual

English

Page 4 www.jacuzzi.com

Pure Air

®

Operations

J2 Pure Air

®

Controls

J4 Pure Air

®

Controls

Fig. 4

BLOWER OPERATION

• Press once to turn ON

• Press again to turn OFF

NOTE: The last blower setting used

is remembered by the system and will

automatically resume upon next use.

INCREASE TOGGLE

• Press to increase the blower inten-

sity

• Press and hold 5 seconds to set/

cancel daily Auto-Dri™

• Alternately, you can press and hold

the button to increase the intensity

level.

DECREASE TOGGLE

• Press to decrease the blower inten-

sity

• Alternately, you can press and hold

the button to decrease the intensity

level

NOTE: When switching be-

tween functions, the LED for

the newly selected function

will FLASH once to indicate

selection.

Fig. 5

BLOWER OPERATION

• Press to turn ON

• Press again to turn OFF

• Use toggles to control speed

INCREASE TOGGLE

• Press to increase selected

feature

• Press and hold 5 seconds to

set/cancel daily Auto-Dri™

• Press to increase light inten-

sity

• Press to turn ON lights at

last color used from OFF

DECREASE TOGGLE

• Press to decrease selected

feature

• Press to decrease light

intensity all the way down

to OFF

CHROMATHERAPY

• Press once to turn lights ON

at white level 2

• Press again to cycle colors

• Press again to stop at the

current color

• Press again to restart the

cycle

• Color Sequence: White,

Purple, Blue, Turquoise,

Green, Yellow, Orange, Red,

Pink, Repeat

PULSE FEATURE

• Press to turn Pulse ON

• Press to turn Pulse OFF

• +/- keys can be used to ad-

just maximum air intensity

WAVE FEATURE

• Press to turn Wave ON

• Press to turn Wave OFF

• +/- keys can be used to

adjust maximum intensity

STATUS LED

• Relays the current intensity

of selected feature

Low

1-2

Medium

Low 3-4

High

7-8

Medium

High 5-6

Operating Manual

English

www.jacuzzi.com Page 5

Pure Air® Auto-Dri™ Air Channels

J2 Auto-Dri™ Air Channels

The blower will operate for 20 minutes and then automatically shut off, unless power is manually turned off. In either

case, 20 minutes after the blower has shut off, it will turn ON for a one-minute drying cycle to blow out any water remain-

ing in the air system.

If the bath is used without the blower operating (showering or bathing without using the Pure Air

®

system), initiate the one-

minute drying cycle manually by use of the ON/OFF switch. Turn the switch ON and OFF again as you exit the bath and

the drying cycle will occur in 20 minutes.

J2 Daily Auto-Dri™ Cycle

To Activate: Holding the button for ve-seconds when the blower is off activates the daily Auto-Dri™ cycle. The blower

will start every day at the same time for one-minute. Once the daily Auto-Dri™ cycle is activated, the blower will come on

for one-second, turn off for two-seconds, come on for one-second and then turn off.

To Deactivate: Holding the button for ve-seconds when the blower is off deactivates the daily Auto-Dri™ cycle. When

the daily Auto-Dri™ cycle is deactivated, the blower will come on for one-second and then turn off.

J4 Auto-Dri™ Air Channels

The Auto-Dri™cycle is automatic and will reduce excessive accumulation of residual water in the air channels.

There are two Auto-Dri™ cycles: drain assisted Auto-Dri™ cycle and daily Auto-Dri™ cycle.

J4 Drain Assist

The Auto-Dri™ cycle is sensor assisted – two sensors (metal dials) are located near the drain of the bathtub. The sensors

detect the presence and absence of water in the bathtub.

To ensure effective and correct operation of the water sensors, it is important to keep them clean and free from block-

age or objects.

After bathing and following the emptying of the bathing well, the sensors detect a “no water” condition. A ve minute wait

time elapses and then the blower is activated. The blower will cycle through a range of speeds for 2 ½ minutes, during

which either 2 or 3 indicator lights will ash at various speeds.

• The Auto-Dri™ cycle will engage even if the blower is not used during bathing.

• The cycle may initiate more than once if the sensors become wet during any part of the Auto-Dri™ operation or during

routine cleaning of the bathtub. This is normal and does not require attention.

•

•

J4 Daily Auto-Dri™ Cycle

Each day, the blower will automatically activate a daily Auto-Dri™ cycle. The blower will operate for one minute on high

power, followed by 15 seconds at ½ power.

To set Auto-Dri™ cycle time: Wait until the time that you desire the daily Auto-Dri™ cycle to activate. With the blower off,

press and hold the plus button for ve seconds. To conrm that you have set the time, the blower will cycle between on

and off two times in a 4 second span.

To cancel daily Auto-Dri™ cycle: With the blower off, press and hold the plus button for ve seconds. To conrm that you

have cancelled the Auto-Dri™ cycle , the blower will come on for 1 second and then stop.

You must set the daily Auto-Dri™ cycle upon installation; the default is no pre-set daily Auto-Dri™ cycle.

If a power failure occurs, the system will default to no daily Auto-Dri™ cycle.

Operating Manual

English

Page 6 www.jacuzzi.com

Pushbutton Whirlpool Schematic Diagram

CONTROL PANEL

PUMP/MOTOR

120VAC 20A

Dedicated GFCI

Circuit Required

CONTROL BOX

120 VAC

PUMP

FOR MODELS

WITH IN-LINE

HEATER

OR

PUMP

PUMP/MOTOR

120VAC 15A

Dedicated GFCI

Circuit Required

Whirlpool System Reference Illustrations

Fig. 6

J2 Control Panel Whirlpool Schematic Diagram

Fig. 7

Operating Manual

English

www.jacuzzi.com Page 7

CONTROL PANEL

120VAC

PUMP

PUMP/MOTOR

CONTROL BOX

120V 20A

Decidated GFCI

Circuit Breaker

120V 15A

Decidated GFCI

Circuit Breaker

FOR MODELS

WITH IN-LINE

HEATER

CHROMATHERAPY

LIGHTS

Fig. 9

Whirlpool System Reference Illustrations (Continued)

J4 Control Panel Whirlpool Schematic Diagram

J2 Control Panel Whirlpool with Chromatherapy Schematic Diagram

CONTROL PANEL

AIR VALVE

ASSEMBLY

CHROMATHERAPY

LIGHTS 2X

LEAD CONNECTIONS

4-WHITE-C

3-BLACK-H

2-N/A

1-GREEN-GRD

VIEW A

LEAD CONNECTIONS

4-WHITE-C

3-BLACK-H

2-RED-L

1-GREEN-GRD

VIEW B

CONTROL BOX

120VAC

Pump

Panel

Blower

LED Light

PUMP/MOTOR

ILLUMATHERAPY

LIGHTS 4X

OR

120VAC 15A

Dedicated GFCI

Circuit Required

120VAC 20A

Dedicated GFCI

Circuit Required

SEE VIEW B

SEE VIEW A

OR

PUMP/MOTOR

Air Valve

FOR MODELS

WITH IN-LINE

HEATER

Fig. 8

Operating Manual

English

Page 8 www.jacuzzi.com

Fig. 11

J2 Whirlpool Controls

J2 Whirlpool Controls with Chromatherapy Controls

Fig. 12

Whirlpool Operations

CHROMATHERAPY

• Press once to turn lights ON at

white level 2

• Press again to cycle colors

• Press again to stop at the cur-

rent color

• Press again to restart the cycle

• Color Sequence: White, Purple,

Blue, Turquoise, Green, Yellow,

Orange, Red, Pink, Repeat

INCREASE TOGGLE

• Press to increase light intensity

• Press to turn ON lights at last

color used from OFF

NOTE: Default lighting color is

white level 2.

DECREASE TOGGLE

• Press to decrease light inten-

sity all the way down to OFF

NOTE: Default lighting color is

white level 2.

• Press once to turn ON.

• Press again to turn OFF.

• Press once to turn ON.

• Press again to turn OFF.

Pushbutton Whirlpool Controls

Fig. 10A

ON/OFF Button

Push down on the button to

turn ON the whirlpool system.

Push down on the button to

turn OFF the whirlpool system.

Whirlpool Control

Fig. 10B

In the closed position, the

jets massage with only

water.

In the open position, air

mixes with water to create a

deep, wide plume of

massaging bubbles.

OPEN Position

CLOSED Position

Operating Manual

English

www.jacuzzi.com Page 9

Whirlpool Operations (Continued)

J4 Whirlpool Controls

Fig. 13

NOTE: When switching be-

tween functions, the LED for

the newly selected function

will FLASH once to indicate

selection.

WHIRLPOOL

• Press to turn ON

• Press again to turn OFF

• Use toggles to control

speed*

* Whirlpool speed available

only for models equipped

with 2-speed motors.

INCREASE TOGGLE

• Press to increase selected

feature

• Press to increase light inten-

sity

• Press to turn ON lights at last

color used from OFF

DECREASE TOGGLE

• Press to decrease the

selected feature

• Press to decrease light

intensity all the way

down to OFF

LEFT AIR VALVE CONTROL

• Press to activate the left air

valve

• Use toggles to control air

mix

RIGHT AIR VALVE CONTROL

• Press to activate the right air

valve

• Use toggles to control air mix

WAVE FEATURE

• Press to turn Wave ON

• Press to turn Wave OFF

• +/- keys can be used to

adjust maximum intensity

CHROMATHERAPY

• Press once to turn lights

ON at white level 2

• Press again to cycle

colors

• Press again to stop at the

current color

• Press again to restart the

cycle

• Color Sequence: White,

Purple, Blue, Turquoise,

Green, Yellow, Orange,

Red, Pink, Repeat

STATUS LED

• Relays the current intensity of

selected feature

Operating Manual

English

Page 10 www.jacuzzi.com

Heated Soak System Reference Illustrations

J2 Control Panel Heated Soak Schematic Diagram

Fig. 14

J2 Control Panel Heated Soak with Chromatherapy Schematic Diagram

Fig. 15

CONTROL PANEL

PUMP/MOTOR

CONTROL BOX

120 VAC

Pump

120VAC 15A

GFCI

PUMP/MOTOR

CONTROL PANEL

CHROMATHERAPY

LIGHT

CONTROL BOX

120 VAC

Pump

Panel

LED Light

120VAC 15A

GFCI

Operating Manual

English

www.jacuzzi.com Page 11

Fig. 16

J2 Heated Soak Controls

J2 Heated Soak with Chromatherapy Controls

Fig. 17

Heated Soak System Reference Illustrations (Continued)

CHROMATHERAPY

• Press once to turn lights ON at

white level 2

• Press again to cycle colors

• Press again to stop at the cur-

rent color

• Press again to restart the cycle

• Color Sequence: White, Purple,

Blue, Turquoise, Green, Yellow,

Orange, Red, Pink, Repeat

INCREASE TOGGLE

• Press to increase light intensity

• Press to turn ON lights at last

color used from OFF

NOTE: Default lighting color is

white level 2.

DECREASE TOGGLE

• Press to decrease light inten-

sity all the way down to OFF

NOTE: Default lighting color is

white level 2.

• Press once to turn ON.

• Press again to turn OFF.

• Press once to turn ON.

• Press again to turn OFF.

Operating Manual

English

Page 12 www.jacuzzi.com

Whirlpool Operations (Continued)

CAUTION: Never run the whirlpool system with all the jets closed.

To adjust the direction of the jets:

• To change the direction of the water ow, swivel the jet nozzle to the desired angle (Figure 18).

To adjust the water ow to the jets:

• Increase the force of the ow by rotating the nozzle or jet face to the left (counterclockwise). Decrease the force of the

ow by rotating the nozzle or jet face to the right (clockwise). Reference Figure 19.

RapidHeat™

RapidHeat™ (Standard on Salon

®

Spa Models)

The heater turns ON automatically any time whirlpool operation is active. Heater

operation is not displayed on the control panel. There is a visible indicator light on the

heater itself that signies the heater is operating (Figure 21). The heater will help main-

tain the temperature of the water in the bathtub. It is not intended to heat the water to a

desired temperature.

Vacuum Switch

The heater is equipped with a preset vacuum switch which will not allow

the heater to turn ON if the pump is not running and water is not owing

through the whirlpool system.

High-Limit Switch

The heater includes an exclusive High-Limit switch (Figure 21). This safety circuit will not false trip from hot tap water. It

will only turn OFF the heater if the thermostat fails. To reset, press the button. If the high-limit trips frequently, please con-

tact us at www.jacuzzi.com, or at 1-800-288-4002.

PUSH TO RESET

OVER HEAT

PROTECTION

HEATER ON

High Limit

Reset

Heater

On

Fig. 21

IMPORTANT NOTE:

Heater will only work when

the water temp is 77°F or

above. You should always fill

the tub with warm water.

Fig. 18 Fig. 19

Controlling Whirlpool Direction & Flow

Controlling Waterfall (Applicable Models Only)

Turning the Waterfall Control knob

counter-clockwise will turn on the waterfall

Turning the Waterfall Control knob

clockwise will turn off the waterfall

Turning ON... Turning OFF...

The more the waterfall control knob is turned in a counter-

clockwise direction, the ow of water will increase. Reference

Figure 20.

The waterfall can only be activated when the whirlpool

pump is in operation.

Fig. 20

To remove accumulations of bathtub residue from the system, it is recommended that a bathtub be cleaned at least twice

a month. For best results, however, we recommend that you clean your bathtub after each use using Systems Clean™,

our exclusive two-part plumbing system cleaner made specically for bathtubs. Systems Clean™ is available through an

authorized Jacuzzi Luxury Bath distributor, by calling 1-800-288-4002 or may be purchased online at www.jacuzzi.com.

Operating Manual

English

www.jacuzzi.com Page 13

Cleaning

Systems Clean™

To remove accumulations of bathtub residue from the whirlpool system, it is recommended that a Whirlpool bathtub be

cleaned at least twice a month. For best results, we recommend that you clean your Whirlpool bathtub after each use us-

ing Systems Clean™, our exclusive two-part plumbing system cleaner made specically for Whirlpool bathtubs. Systems

Clean™ is available through an authorized Jacuzzi Luxury Bath distributor by calling us direct at 1-800-288-4002, or may

be purchased online at www.jacuzzi.com/baths.

Bathtub Additives

CAUTION: Do not use oil or oil-based bathtub additives. Never use abrasive or caustic household cleaners on any

Jacuzzi Luxury Bath product.

If you want to use any kind of bathtub additive, use only a small amount of low-foaming powder or crystal substance; the

whirlpool action intensies the foaming properties of soaps.

The use of certain bathtub oils, bubble baths, and bathtub additives may increase the level of accumulations of bathtub

residue in the Whirlpool system and may cause false reading of the water level sensors. If excess accumulations persist,

you should discontinue use of these products.

To remove accumulations of bathtub residue from the Whirlpool system, it is recommended that a bathtub be cleaned

regularly. For best results, we recommend that you clean your Whirlpool bathtub after each use using Systems Clean™,

our exclusive two-part plumbing system cleaner made specically for Whirlpool bathtubs. Systems Clean™ is available

through an authorized Jacuzzi Luxury Bath distributor, or by calling 1-800-288-4002 or may be purchased online at

www.jacuzzi.com.

To clean your bathtub, simply use a mild, non-abrasive liquid detergent solution. You can protect and restore the gloss to a

dulled acrylic surface by applying Meguiar’s #10 Mirror Glaze, a product specically designed for use on acrylic nishes. If

Meguiar’s is not available, use a ne grade automotive rubbing compound followed by an application of clear automotive

paste wax.

Minor scratches which do not penetrate the color nish can be removed by lightly sanding with 600-grit wet/dry sandpaper.

Restore the gloss using Meguiar’s Mirror Glaze or automotive paste wax. Major scratches and gouges which penetrate

the acrylic surface will require renishing. Call Jacuzzi Luxury Bath to nd a service agent in your area.

If hair, or other types of debris, get caught in the bearings of these jets, it could cause

them to stop spinning (Figure 22). This may require disassembly and removal. To do this,

simply grab the nozzle and pull it straight out of the jet housing. The bearing casing will be

attached to the nozzle. These two items can be separated by holding the casing and push-

ing the nozzle out from the rear of the casing. After the cleaning is complete, reassemble

and reinstall.

Maintenance

Spinning Jet Maintenance

Fig. 22

Operating Manual

English

Page 14 www.jacuzzi.com

Clean the suction cover/strainer of hair and debris when necessary (Figure 23).

1. Remove the center screw and detach the suction cover.

2. Clean the cover by back ushing debris from the holes.

3. Replace the suction cover immediately after cleaning.

WARNING! When reinstalling, orient the cover/strainer with the small

notch at the bottom. The gasket must be inserted into the groove of the

cover/strainer before reinstalling onto the suction tting.

DANGER: RISK OF SEVERE INJURY OR DROWNING! Keep hair a

minimum of 6 inches (152 mm) away from the suction tting at all times when the whirlpool system is operating. Hair

longer than shoulder length should be secured close to the head, or a bathing cap should be worn.

DANGER: RISK OF SEVERE INJURY OR DROWNING! Do not operate the Whirlpool system with the suction

cover/strainer removed! It is a safety device and must always be in place on the suction tting to minimize the potential

hazard of hair and body entrapment.

Maintenance (Continued)

Whirlpool Suction Cover/Strainer Maintenance

Fig. 23

Operating Manual

English

www.jacuzzi.com Page 15

Salon

®

Spa System Reference Illustrations

J4 Control Panel Salon

®

Spa Schematic Diagram

CONTROL

PANEL

CHROMATHERAPY

LIGHTS 2X

LEAD CONNECTIONS

4-WHITE-C

3-BLACK-H

2-N/A

1-GREEN-GRD

VIEW A

Air Valve

ILLUMATHERAPY

LIGHTS 4

SEE VIEW A

240VAC/20A

Dedicated GFCI

Required

AIR VALVE

ASSEMBLY

CONTROL BOX

240VAC

Pump

OR

Panel

Blower

LED Light

PUMP/MOTOR

120VAC 15A

Dedicated GFCI

Required

FUSE

FUSE

FUSE

FUSE

BLOWER

HEATER

FUSE/JUNCTION

BOX

AUTO-DRI™

SENSOR CABLES

CHROMATHERAPY

LIGHTS 2X

1

2

3

4

VIEW A

SEE VIEW A

PUMP/MOTOR

ILLUMATHERAPY

LIGHTS 4X

FUSE

FUSE

FUSE

FUSE

BLOWER

HEATER

CONTROL BOX

Air Valve

240VAC

Pump

RS232

Panel

Blower

Inside

Light 1

Inside

Light

3

Ambient

Light 1

Temp

Sensor

Inside

Light

2

Inside

Light

4

LOGO

Light

Ambient

Light

2

TEMPERATURE

SENSOR

OR

AUTO-DRI™ SENSOR CABLES

CONTROL

PANEL

240VAC/20A

Dedicated GFCI

Required

AIR VALVE

ASSEMBLY

LEAD CONNECTIONS

4-GREEN-(GRD)

3-RED-(L)

2-BLACK-(H)

1-WHITE-(C)

120VAC 15A

Dedicated GFCI

Required

FUSE/

JUNCTION BOX

Fig. 24

Fig. 25

J5 Control Panel Salon

®

Spa Schematic Diagram

Operating Manual

English

Page 16 www.jacuzzi.com

Salon

®

Spa Operations

J4 Salon

®

Spa Controls

Pure Air

®

and Auto-Dri™ Air Channels

For complete operating instructions reference page 5.

J5 Salon

®

Spa Controls

Controlling Whirlpool Direction and Flow

For complete operating instructions reference page 12.

Fig. 26

NOTE: When switching be-

tween functions, the LED for

the newly selected function

will FLASH once to indicate

selection.

WHIRLPOOL

• Press to turn ON

• Press again to turn OFF

• Use toggles to control

speed

INCREASE TOGGLE

• Press to increase selected

feature

• Press and hold 5 seconds to

set/cancel daily Auto-Dri™

• Press to increase light inten-

sity

• Press to turn ON lights at last

color used from OFF

DECREASE TOGGLE

• Press to decrease the

selected feature

• Press to decrease light

intensity all the way

down to OFF

LEFT AIR VALVE CONTROL

• Press to activate the left air

valve

• Use toggles to control air

mix

RIGHT AIR VALVE CONTROL

• Press to activate the right air

valve

• Use toggles to control air mix

WAVE FEATURE

• Press to turn Wave ON

• Press to turn Wave OFF

• +/- keys can be used to

adjust maximum inten-

sity.

CHROMATHERAPY

• Press once to turn lights

ON at white level 2

• Press again to cycle

colors

• Press again to stop at the

current color

• Press again to restart the

cycle

• Color Sequence: White,

Purple, Blue, Turquoise,

Green, Yellow, Orange,

Red, Pink, Repeat

STATUS LED

• Relays the current intensity of

selected feature

PURE AIR

®

FEATURE

• Press to turn ON

• Press again to turn OFF

• Use toggles to control

intensity

POWER

Main Menu

J5 Control Panel

Optional J5 Luxury LCD Control Panel: Operation instructions for this panel are

outlined in the supplemental guide provided in your warranty pack. Refer to this

document for complete operation details (P/N GU47000).

Operating Manual

English

www.jacuzzi.com Page 17

Troubleshooting Procedures

PROBLEM PROBABLE CAUSES REMEDY

Pump/motor does not start • No power to pump/motor

• Pump/motor not plugged in

• Pump/motor faulty

• Reset GFCI

• Insert plug securely into outlet

• Ensure control panel is connected to control box

• Contact Jacuzzi Luxury Bath @ 800-288-4002

Pump/motor operates but no fully

adjustable jets are functioning

• Jets are closed

• Suction cover/strainer may be clogged

• Open jets by rotating counter-clockwise

• With the motor turned OFF, remove the suction

cover/strainer and remove any debris. Replace the

suction cover before operating

Pump/motor operates but air is not

injected into the water

• Air valves are closed • Open air control valves

Water leakage from pump unions • Overtightened, O-ring may be pinched or improp-

erly seated, undertightened

• Loosen unions, check and reseat O-ring. If O-ring

has been pinched out of shape, replace (refer to

number below). When tightening union nuts, hand

tighten only

Pump/motor shuts off by itself before

time elapses

• Motor thermal protection has deactivated pump/

motor due to overheating (supply voltage low)

• GFCI tripped

• Inadequate supply wiring

• Let motor cool; thermal protection will reset. Check

for proper ventilation (check supply voltage)

• Reset GFCI; if it continues to trip, do not use this

unit. Disconnect the unit and have the problem cor-

rected by a licensed electrician before using

• Consult a licensed electrician to correct the wiring

unit

Chromatherapy lights do not operate • Connector has come loose • Contact Jacuzzi Luxury Bath @ 800-288-4002

Blower does not start • No power to pump/motor

• Blower not connected

• Blower faulty

• Reset GFCI and/or breaker

• Ensure plug is fully in outlet

• Ensure control panel is connected to control box

• Ensure control box is connected to control panel

• Contact Jacuzzi Luxury Bath @ 800-288-4002

Blower operates but NO air is exiting

the holes

• Check valves are stuck in the closed position • Contact Jacuzzi Luxury Bath @ 800-288-4002

Blower operates but air is not exiting

all of the holes

• Blower intensity is not sufcient

• Obstructed air holes

• Increase the blower intensity. NOTE: The system is

designed such that all air channels operate at the 4th

blower setting.

• Remove debris with a toothpick or tooth brush

Blower shuts off unexpectedly • 20 minute timer has elapsed

• GFCI tripped

• Inadequate supply wiring

• Improper ventilation

• Connector has come loose

• Turn on blower

• Reset GFCI; if it continues to trip, do not use the unit

• Consult a licensed electrician to correct

• Contact Jacuzzi Luxury Bath @ 800-288-4002

Drain assist Auto-Dri™ cycle comes

on multiple times

• Water sensors detect multiple wet and dry condi-

tions

• If during a Auto-Dri™ cycle, water is coming in

contact with both sensors, the system is working as

designed and will continue to Auto-Dri™ until excess

water is expelled

• Remove any washcloth or toy that may be covering

the sensors

Drain assist Auto-Dri™ does not

come on 5 minutes after bathtub is

drained out completely

• Water sensors not connected and not detecting

water being drained out of the tub

• Faulty control box

• Contact Jacuzzi Luxury Bath @ 800-288-4002

Water not maintaining temperature • High limit switch on heater has tripped • Press Reset button on heater

Waterfall not working • Whirlpool function not on

• Waterfall control knob is in the OFF position

• Debris in waterfall outlet

• Turn on whirlpool

• Turn waterfall control knob counter-clockwise until

water ow is at the desired ow

• Use a thin, rigid and non-abrasive material (ie. credit

card) and gently swipe back and forth until debris is

cleared away from the waterfall opening

If the unit is within the warranty period, contact Jacuzzi Luxury Bath Service Support at 1-800-288-4002 with your

bath’s serial number before work is started. The serial number is located on the Specication/Serial Number

Plate.

Operating Manual

English

Page 18 www.jacuzzi.com

Notes:

Jacuzzi Luxury Bath

14525 Avenue Monte Vista

Chino, CA 91710 États-Unis

1-800-288-4002

www.jacuzzi.com

Pure Air

MD

Baignoire d’hydromassage

Spa Salon

MD

MANUEL D’UTILISATION

LG74000D 06/2019

Manuel d’utilisation

Français

Page 2 www.jacuzzi.com

Renseignements généraux sur l’utilisation. ..................................................................................................................... 2

Illustration de référence d’un système Pure Air

MD

. ......................................................................................................... 3

Opérations de Pure Air

MD

. ............................................................................................................................................... 4

Canaux d’air Pure Air

MD

Auto-Dri

MC

. ................................................................................................................................ 5

Illustrations de référence du système de baignoire d’hydromassage. ......................................................................... 6-7

Opérations de la baignoire d’hydromassage. ............................................................................................................... 8-9

Schémas de référence du système de chauffage .................................................................................................... 10-11

RapidHeat

MC

. ................................................................................................................................................................. 12

Nettoyage. ..................................................................................................................................................................... 13

Entretien. .................................................................................................................................................................. 13-14

Illustrations de référence du système de spa Salon

MD

................................................................................................. 15

Opérations du spa Salon

MD

. ......................................................................................................................................... 16

Procédures de dépannage. ........................................................................................................................................... 17

*For Spanish and French installation instructions, please visit www.jacuzzi.com/baths/support/owners-manuals/.

*Para instrucciones de instalación en español, por favor visite www.jacuzzi.com/baths/support/owners-manuals/.

*Pour les directives d'installation en français canadien, veuillez visiter www.jacuzzi.com/baths/support/owners-manuals/.

Table des matières

Renseignements généraux sur l’utilisation

Toutes les baignoires fabriquées par Jacuzzi Luxury Bath sont conçues pour « remplissage et évacuation », ce qui signie

que la baignoire doit être vidée après chaque utilisation et remplie d’eau fraîche par le baigneur suivant. Il s’agit d’une

précaution de santé puisque ces baignoires ne sont pas conçues pour conserver de l’eau continuellement comme les

piscines ou les spas.

Fermez l’évacuation et remplissez la baignoire jusqu’à ce que l’eau soit à au moins 25 à 51 mm (1 à 2 po) au-dessus du

jet le plus élevé ou de l’entrée d’air (reportez-vous à la ligne d’eau indiquée dans l’illustration – Figure 1). Ne mettez pas

le système PureAir

MD

de la baignoire d’hydromassage en marche si les jets ou commandes d’air ne sont pas complète-

ment immergés dans l’eau. Faire fonctionner la baignoire d’hydromassage ou le système PureAir

MD

lorsqu’il n’y a pas

assez d’eau peut entraîner la pulvérisation de l’eau à l’extérieur de la baignoire.

ATTENTION : lorsque vous sortez de la baignoire, le niveau

d’eau s’abaissera sous les jets ce qui pourrait entraîner la

pulvérisation de l’eau à l’extérieur de la baignoire. Pour empêcher

cette pulvérisation, vous devez éteindre l’unité avant de sortir de

la baignoire.

Remplir jusqu’à une

distance d’au moins

2,5 à 5 cm au-dessus

du jet le plus élevé

Fig. 1

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

/

Related papers

Other documents