2. Vehicles & accessories
  3. Motor vehicle accessories & components
  4. Motorcycle Accessories
  5. Crux
  6. SWRNS-63T
SWRNS-63T

Crux SWRNS-63T Owner's manual

  • Hello! I've reviewed the user manual for the Crux SWRNS-63T Radio Replacement Interface. This device is designed to help you install an aftermarket radio in select Nissan vehicles while retaining steering wheel controls and supporting both Bose and non-Bose sound systems. It also includes EIA color-coded wiring for easy install. I'm ready to answer any specific questions you have about its features or installation process.
  • What Nissan vehicles are compatible with this interface?
    Does this interface support Bose sound systems?
    What is the purpose of the DIP switches?
    What does the blue LED light indicate?
    What does it mean when red LED flashes?
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev. 081022
SWRNS-63T
Radio Replacement with Steering Wheel Control Retention
for Select NISSAN Vehicles 2005-2011
1 of 2
RADIO REPLACEMENT
SWC RETENTION
+
R
INTERFACING SOLUTIONS
- Retains factory features in select Nissan vehicles while funconing with an aermarket radio.
- Pre-programmed to retain steering wheel controls.
- Supports Bose amplied and non-amplied systems.
- EIA color coded wiring for easy installaon.
PRODUCT FEATURES:
PARTS INCLUDED:
SWRNS-63T Module SWRNS-63T Harness SWC Cable
INSTALLATION DIAGRAM:
AFTERMARKET
RADIO
+12V Constant Yellow
+12V ACC Red
Ground Black
Additional Ground Black
Illumination Orange
Not Used Orange/White
Amp Turn On Blue/ White
Power Antenna Blue
Right Front (+) Gray
Right Front (-) Gray/Black
Left Front (+) White
Left Front (-) White/Black
Right Rear (+) Violet
Right Rear (-) Violet/Black
Left Rear (+) Green
Left Rear (-) Green/Black
Not Used Light Green
Chassis Ground Black
(with Ring Terminal)
TO FACTORY
HARNESS
12-Pin Black
Connector
16 PIN
10 PIN
6 PIN
16 PIN “A”
“B”
16-Pin
Connector
“A”
16-Pin
Connector
“B”
Pink
Black
Light Blue Pink
Black
Light Blue
WIRE VIEW
Refer to VEHICLE APPLICATIONS
on page 2 for “A” and “B” Connection
4-Pin
Connector
Cap or insulate if
not being used
Kenwood/JVC (BLUE / YELLOW)
Insulate with tape
if not being used
3.5MM SWC CABLE
Plug in the 3.5MM SWC cable to the 4-pin port
on the module. See “DIP SWITCH SETTINGS” section.
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
AFTERMARKET
RADIO SELECTOR
(See Chart)
NISSAN
SWC SETTING
(OFF ON OFF OFF)
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
To aftermarket
radio SWC port
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev. 081022
SWRNS-63T
Radio Replacement with Steering Wheel Control Retention
for Select NISSAN Vehicles 2005-2011
2 of 2
RADIO REPLACEMENT
SWC RETENTION
+
R
INTERFACING SOLUTIONS
DIP SWITCH SETTINGS:
AFTERMARKET RADIO DIP SWITCH SETTINGS:
NOTE: Insulate the Blue/Yellow wire or the 3.5mm plug if not being used.
RADIO BRAND: DIP: 1 2 3 4
Atoto, Dual, Farenheit, Jensen, Pioneer
Power Acoustik, Soundstream
Blaupunkt, Most o-brand Radios
Alpine
Clarion
Kenwood
JVC
Boss, Old Sony
New Sony
OFF OFF ON ON
OFF OFF ON ON
OFF OFF ON ON
OFF OFF OFF OFF
OFF ON ON OFF
OFF ON ON ON
OFF ON OFF ON
OFF ON OFF OFF
OFF OFF ON OFF
SWC MODULE
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
NOTE: For Atoto, Blaupunkt, Dual, Farenheit, Power Acoustik, Soundstream, and most o-brand radios,
check the aftermarket radio’s manual to see if the SWC buttons need to be programmed.
3.5MM SWC CABLE
Plug in the 3.5MM to 4-Pin SWC cable to the SWC module.
NISSAN STEERING WHEEL CONTROL DIP SWITCH SETTING:
DIP: 5 6 7 8
Nissan OFF ON OFF OFF
SWC MODULE
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
VEHICLE APPLICATIONS:
NISSAN
Using Connector “A” (see installaon diagram)
2005 – 2006 Alma
2006 Maxima
2005 – 2006 Froner
2005 – 2006 Pathnder
2005 – 2006 Xterra
Using Connector “B” (see installaon diagram)
2007 – 2011 Froner
2009 – 2010 Titan
2007 – 2010 Xterra
NOTE: Analog Signal Output provided may not cover all model/year listed.
RED to SWC Key 1
WHITE to SWC Key 2
SHIELD to SWC Ground
For aermarket radios that have wires for SWC connecons, cut o the 3.5mm plug on the Crux SWC Cable and connect the
SWC wires as follows:
Note that there are some radios that only have SWC1 and SWC2, in this case “shield” does not need to be connected.
/