2. VISUAL COMFORT
  3. TOB 5453

VISUAL COMFORT TOB 5453 User manual

  • Hello! I'm a chat assistant and I've reviewed the assembly instructions for the Visual Comfort Chandelier TOB 5453. This document provides a step-by-step guide on how to put together and install your new light fixture, including wiring instructions and safety precautions. It also gives detailed steps on what to do and what not to do during installation. I'm ready to answer any specific questions you might have about the contents of this document.
  • What tools are required for the installation?
    What should I do if I find a damaged part?
    Is there a caution about electrical connections?
1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove mounting plate (B) from canopy (F) by removing collar
ring (G).
3. Install mounting plate (B) to junction box and secure with mounting
screws (C).
4. Feed electrical wires through bottom rod (J) and connect to fixture
body (K). Repeat for middle rod (I), connecting to bottom rod (J).
5. Feed electrical wires through top rod (H) and remove swivel ball (Q)
from top rod (H).
6. Let collar ring (G) and canopy (F) pass though top rod (H), then
secure swivel ball (Q) to top rod (H) and connect top rod (H) to
middle rod (I).
7. Hang fixture swivel ball (Q) to the center of mounting plate (B) and
secure with set screw (D) with provided wrench (E).
NOTE: Slide components down slowly to avoid damages.
8. Cut excess wires, being sure to leave enough to reach the junction
box. Separate wires, and strip insulation on each 5/8".
9. Wrap fixture ground wire (bare copper) around the green grounding
screw (see diagram 1). Tighten. Continue fixture ground wire and
connect to supply ground wire (usually green or bare copper) using
wire nut (A).
NOTE: It is imperative that the fixture is grounded.
Piaf Grande Two-Tier Chandelier
Item # TOB 5453
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver Slotted Screwdriver Wire Cutters
Wire Strippers
NOTICE:
A
CB
G
Diagram 1
Bulbs not included
ED
Q
F
I
J
K
L
H
US
M
L
I
D
S
E
T
10. Connect fixture neutral wire (white) to the supply neutral wire (usually
white) using wire nut (A).
11. Connect fixture hot wire (black) to the supply hot wire (usually black)
using wire nut (A).
CAUTION: Do not reverse the hot and neutral connections.
12. Make sure all wire connections are tight, then carefully tuck into the
junction box.
13. Install canopy (F) to mounting plate (B) and secure with collar ring (G).
14. Install light bulbs into the sockets.
15. Clip shades (L) onto the bulbs.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
Not use abrasive or chemical agents.
Piaf Grande Two-Tier Chandelier
Item # TOB 5453
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
NOTICE:
US
M
L
I
D
S
E
T
A
CB
G
Diagram 1
Bulbs not included
ED
Q
F
I
J
K
L
H
/