Eaton Green Motion Building Cable Holder Installation guide

Brand: Eaton

Model: Green Motion Building Cable Holder

Type: Installation guide

Eaton Green Motion Building Cable Holder keeps your EV charger cable organized and protected. Easily mount it on the wall using the included adhesive gaskets and screws. The cable holder features a cable throughput for easy cable management, ensuring your charging station stays neat and tidy. Compatible with Eaton Green Motion Building EV chargers.

Figure 1. Green Motion Home and Green Motion Building cable

holder with dimensions

Figure 2. Drilling template for the Green Motion Home and the Green

Motion Building EV chargers with the cable holder

Figure 4. Fixing the EV charger and cable holder to the wallFigure 3. Mounting of the cable holder on the wall

1500 mm (59 inch)

86 mm (3.4 inch)

226 mm

(8.9 inch)

190.5 mm

(7.5 inch)

206 mm

(8.1 inch)

60 mm (2.3 inch)

60 mm

(2.3 inch)

Ø 6,2 mm

(0.2 inch)

190 mm

(7.4 inch)

65 mm (2.5 inch)

100 mm

(3.9 inch)

220 mm (8.6 inch)

300 mm (11.8 inch)

50 mm

(12.0 inch)

Ø 18,5 (x2) mm

(0.7 inch)

30 x 50 mm

(1.1 x 1.9 inch)

1,5 mm

(0.5 inch)

Never turn on equipment when there is evidence of re or structural damage. Green Motion Home and Green Motion Building cable holder must be installed only by professional and qualied personnel.

Number Description

1Drilling template of Green Motion Home

and Green Motion Building EV chargers

2Cable holder

3Hole

4Cable throughput

5Floor

Number Description

1EV charger

2Cable holder

3Power and communication cables

4Holes

5Adhesive gaskets

Number Description

1Mounting slots

2Optional mounting slot

Number Description

1Ø6-mm screws

Prior to installation it is required to download (www.eaton.com/greenmotionbuilding or www.eaton.com/

greenmotionhome), read, and understand the step-by-step instructions from the latest installation manual.

Eaton Green Motion Home and Green Motion Building cable holder

Accessory leaﬂet

2. Installation method1. Technical speciﬁcations

Read and understand the safety instructions and warnings prior to installation.

Technical disclaimer

All drawings, descriptions or illustrations contained in this document

serve to provide a clear overview and/or technical explanation of the

present product and its various components and accessories.

In line with our goal to continuously improve the products and the

customer service we provide, all specifications contained in this

document are subject to change without notice.

The Green Motion Home and Green Motion Building cable holder

supports the cable attached to the EV charger.

Dimensions and weight

The table below shows the dimensions and weight of the Green

Motion Home and Green Motion Building cable holder.

• the type of wall on which the EV charger and cable holder are to be

mounted,

• the local rules and regulations.

Mounting

Step 1. Use a spirit level to place the drilling template of the Green

Motion Home or Green Motion Building EV charger on the wall.

Make sure the template’s top is at a height of 1500 mm from

ground level, for optimal accessibility.

Step 2. Mark the holes with a pencil and remove the drilling template.

Step 3. Drill four holes in the wall according to the drilling template and

measurements shown in Figure 2. Make sure to not damage any

cables in the wall.

Step 4. (Optional) Pull the power and communication cables through the

cable throughput in the cable holder as indicated in Figure 3.

Step 5. Place four adhesive gaskets around the four slots on the

outside of the unit and align the two mounting slots of the

cable holder with the lower two mounting slots of the EV

charger. See Figure 3.

Step 6. Screw the EV charger and cable holder to the wall with four

⌀6-mm screws. See Figure 4.

Step 7. (Optional) The cable holder can be xed to the wall with an extra

⌀6-mm screw. See Figure 1. Make sure to not damage any

cables in the wall.

Tools required for the installation

To perform the installation, professional and qualied personnel

should have the following tools:

• Screwdriver

• Drilling machine

Materials required for the installation

To perform the installation, professional and qualied personnel

should have the following materials:

Please note that the appropriate type of screws and wall plugs

must be selected by professional and qualied personnel, based

on the following considerations:

• the installation location,

Green Motion Home and Green Motion Building

cable holder

Dimensions (H x W x D) in mm 300 x 220 x 60

Weight in kg 0.4

Installation method Wall-mounted

Green Motion Home and Green Motion

Building cable holder

Provided by

Eaton

One cable holder ✔

Four adhesive gaskets ✔

Four Ø6-mm screws ✘

Four wall plugs ✘

Eaton Green Motion Building Cable Holder Installation guide

Eaton Green Motion Building Cable Holder Installation guide

Eaton Green Motion Building Cable Holder Installation guide

Related papers

Other documents