BEA IXIO SMART DAISY CHAIN HUB User guide
- Type
- User guide
SDC HUB
1
6
5
4
2
3
E
R
L
A
U
B
T
Z
E
R
T
I
F
I
Z
I
E
R
U
N
G
N
A
C
H
EN 16005
E
N
A
B
L
E
S
A
C
C
O
R
D
A
N
C
E
W
I
T
H
E
R
L
A
U
B
T
Z
E
R
T
I
F
I
Z
I
E
R
U
N
G
N
A
C
H
DIN 18650
E
N
A
B
L
E
S
A
C
C
O
R
D
A
N
C
E
W
I
T
H
* Other use of the device is outside of the permitted purpose
and can not be guaranteed by the manufacturer.
TECHNICAL SPECIFICATIONS
DESCRIPTION
ENGLISH
SMART DAISY CHAIN ACCESSORY
FOR IXIO-DT3*
1. connector to door controller
2. optional connector (not used)
3. switch for sensor number
4. connector to sensor 1/2 or 1/3
5. connector to sensor 2/3
6. connector to sensor 2/2 or 3/3
Power consumption:
Supply voltage:
Monitoring response time:
Temperature range:
Protection degree:
Dimensions:
Housing material:
Length of sensor cables:
Expected lifetime:
Output:
Test input:
Norm conformity of IXIO-DT3:
< 8 W (depending on number of sensors connected)
12 V DC - 24 V DC +10%
max. 60 ms (depending on number of sensors connected)
from -25° to +55° (0, -95% relative humidity, non condensing)
IP20
70 mm (W) x 55 mm (H) x 25 mm (D)
ABS (translucent blue)
2.50 m
20 years
see specifications of sensor 2/2 or 3/3
see specifications of sensor 1/2 or 1/3
- RADAR: EN 12978; EN ISO 13849-1 PL «d» CAT. 2; EN 16005 Chapter 4.6.8;
DIN 18650-1 Chapter 5.7.4; AutSchR; BS 7036-1:1996 Chapter 7.3.2
(only applicable for relay output in frequency mode and current source output)
- INFRARED: EN 12978; EN ISO 13849-1 PL «c» CAT. 2 (under the condition that the door control
system monitors the sensor at least once per door cycle)
IEC 61496-1 ESPE Type 2; EN 16005 Chapter 4.6.8;
DIN 18650-1 Chapter 5.7.4; BS 7036-1 Chapter 8.1
Specifications are subject to changes without prior notice - Measured in specific conditions and with a temperature of 25°C.
1
12-24 V DC
1
2
3
1
2
3
1/3
1/2
2/3
3/3
2/2
Connect 2 or 3 sensors to the hub.
The cables are marked on both ends to ease the installation.
Position the switch depending on number of sensors connected.
Connect the hub to the door controller.
Use the IXIO-DT3 power cable.
1
st
sensor in chain
2
nd
sensor in chain of 3 sensors
last sensor in chain
If used, always plug the INTERFACE
(door bell, retrofit etc) on the last
sensor only. Follow the instructions
of the interface user’s guide for the
configuration of this sensor.
SDC INTERFACE
DOOR CONTROLLER
GREEN +
BROWN -
YELLOW
WHITE
PINK
GREY
RED
BLUE
YE/BK +
WH/BK -
POWER SUPPLY
OPENING INPUT
SAFETY INPUT
TEST
OUTPUT
OPENING INPUT
FOR CURRENT SOURCE
CONNECTION
SmartDaisyC.
OFF
SmartDaisyC.
SmartDaisyC.
SmartDaisyC.
SmartDaisyC.
SmartDaisyC.
SmartDaisyC.
OFF
SmartDaisyC.
2
1
2
YE/BK +
WH/BK -
1
2
off = factory value
1
st
sensor in chain of 2 sensors (1/2)
2
nd
sensor in chain of 2 sensors (2/2)
1
st
sensor in chain of 3 sensors (1/3)
2
nd
sensor in chain of 3 sensors (2/3)
3
rd
sensor in chain of 3 sensors (3/3)
Back
Redirection
FactoryRst
Configure the Smart Daisy Chain parameter on each sensor depending on its position in
the chain and the number of sensors connected.
When changing this setting, the output and test parameters go into internal communication
mode.
Configure the radar output on the last sensor of the chain.
Rad: Output
NO
Rad: Fieldsize
IR: Immunity
NO: normally open = factory value
NC: normally closed
Current source output for emergency exits
Frequency output for emergency exits
Back
Rad: Output
CONFIGURATION
BEA SA | LIEGE Science Park | ALLÉE DES NOISETIERS 5 - 4031 ANGLEUR [BELGIUM] | T +32 4 361 65 65 | F +32 4 361 28 58 | [email protected] | WWW.BEA-SENSORS.COM
1
3x
1
2
2
3x
©BEA | Original instructions | 42.8450 / V2 - 11.17
BEA hereby declares that the SDC HUB is in conformity with the basic requirements and the other relevant
provisions of the directives RED 2014/53/EU, RoHS 2 2011/65/EU.
Angleur, September 2017 Pierre Gardier, R&D Manager (Authorized representative)
The complete declaration of conformity is available on our website
Only for EC countries: According to the European Guideline 2012/19/EU for Waste Electrical and Electronic Equipment (WEEE)
PLEASE KEEP FOR FURTHER USE - DESIGNED FOR COLOUR PRINTING
ERROR CODES
E3: SDC NOF
Check wiring.
Check sensor position and setting.
No communication
E3: SDC POS
Position error in chain
Check sensor position and setting.
Check wiring.
-
1
-
2
-
3
-
4
