Croydex QM380641YW Installation guide

Type
Installation guide

This manual is also suitable for

Select position of product and
mark centres of mounting holes.
Using a 6mm masonry drill, drill a hole
in the marked position to a depth of
30mm. If drilling through tiles, please
pre-drill using a ceramic drill bit.
WARNINGS
Safety and care advice
1. Always take care when using an electric drill,
particularly in the bathroom. Always check for
hidden cables and pipework before drilling.
Always use a residual current circuit breaker
(RCCB) when using mains powered tools and
take extreme care if there is any water in the
working area.
2. Always wear suitable eye protection when drilling.
3. If the product is to be fitted on a ceramic tiled
wall, a ceramic drill bit should be used. Do not
drill mounting holes in the grouted area between
tiles. Mask the area around the hole with tape
before drilling to prevent damage to the tile.
Mounting your Stick ‘N’ Lock Plus Wall Mounted Accessory using the screw fix method
Component parts requiredIncluded in your pack
1
Insert the wall plug (H) to the surface of
the wall. If fitting to a tiled surface the
wall plug should be inserted below the
surface of the tile to avoid cracking.
Insert the double end fixing screw (G)
into the wall plug up to the shoulder,
as shown.
2 3
Screw Fix Method
Read these instructions carefully
Do not overload - maximum weight 2kg (4.5lbs)
Keep these instructions for future reference
4
Ensure the product is level and
then rotate the cap (E) clockwise
until fully tight.
Do not overtighten.
Your product is now ready to use.
Wall plugs supplied for solid walls only
Ensure correct wall plug for wall type is used
C
H
A
E
Tools Required:
Drill; 6mm Masonry Drill Bit (6mm Ceramic Drill bit optional)
Cross Head Screwdriver; Pencil
(A) Product (C) Bracket Body
(D) Spacer (E) Cap
(G) Double End Fixing Screws (H) Wall Plugs
NON-ILLUSTRATED ITEMS
(B) Adhesive Pad (Used only for adhesive fixing)
(F) Spring (Used only for adhesive fixing)
Wall plugs supplied for solid walls only. Ensure correct wall
plug for wall type is used.
C
G
D
Loving your new Stick ‘N’ Lock Plus product? We have a wide range of bathroom accessories, please visit www.croydex.com for more details.
How to remove your Stick ‘N’ Lock Plus product
Unscrew and remove the cap (E) while supporting the product.
Care and maintenance
Clean with a soft, damp cloth. Never use abrasive or chemical cleaners.
Croydex Limited, Central Way, Andover, Hants, SP10 5AW, UK
Tel: +44 (0) 1264 365881 Fax: +44 (0) 1264 356437
Website: www.croydex.com E-mail: [email protected]
Quantity varies depending on product purchased
With the cap (E) removed, place the
product (A) and bracket body (C)
over the exposed shoulders of each
screw (G) and align cap (E) as shown.
SNL+001 R02
SNL+001 R02
Separate the adhesive pad (B) from
the bracket body (C) by rotating the
cap (E) anti-clockwise.
Note position of spring (F) and keep
to one side for final assembly.
At this stage do not remove the
protective cover from the adhesive pad.
Before installing
1.
Thoroughly clean the mounting surface to
remove any dirt, residue or contaminates
that may reduce the adhesive performance.
2.
Ensure the mounting surface is thoroughly
dry and free from loose, flaky material.
3.
Plan where the product will be located and
mark the wall bracket positions accurately on
on the wall surface before removing the
protective backing from the adhesive pad.
Mounting your Stick ‘N’ Lock Plus Wall Mounted Accessory using the adhesive pad fixing method
Component parts required
Hold the adhesive pad (B) in place on
the wall surface & draw around its edge.
Check the positioning for double
bracket products to make sure the
adhesive pads are level.
If applicable use the template supplied
for double bracket products.
2 3 4
Adhesive Pad Method
1
Remove the protective cover from the
back face of the adhesive pad (B) and
carefully align the pad with the mark on
the wall.
Press in position and apply an even
pressure around the entire pad surface
to ensure full adhesion.
(A) Product
(B) Adhesive Pad
(C) Bracket Body
(D) Spacer
(E) Cap
(F) Spring
NON-ILLUSTRATED ITEMS
(G) Double End Fixing Screws (used only for
screw fixing)
(H) Wall Plugs (used only for screw fixing)
Quantity varies depending on product purchased
E
B
A
D
C
The adhesive pad must be left to cure
for 24 hours before product assembly.
Assemble the components onto the
adhesive pad including the spring (F) and
rotate the cap (E) clockwise until tight.
Do not overtighten.
Your product is now ready to use.
Loving your new Stick ‘N’ Lock Plus product? We have a wide range of bathroom accessories, please visit
www.croydex.com for more details.
How to remove your Stick ‘N’ Lock Plus product
Unscrew and remove the cap (E) while supporting the product.
The adhesive pad can be removed by carefully inserting a flat, blunt instrument between the bracket and the wall surface.
Care and maintenance
Clean with a soft, damp cloth. Never use abrasive or chemical cleaners.
Adhesive residue can be removed by carefully scraping the wall surface with a blunt instrument.
Croydex Limited, Central Way, Andover, Hants, SP10 5AW, UK
Tel: +44 (0) 1264 365881 Fax: +44 (0) 1264 356437
Website: www.croydex.com E-mail: [email protected]
Included in your pack
WARNINGS
Read these instructions carefully
The adhesive pad is suitable for use on most flat, finished surfaces, such as
gloss paint, tiles, polished stone, laminates and mildly textured surfaces
Do not use on decorative wall paper finishes as these will be damaged on removal
Do not overload - maximum weight 2kg (4.5lbs)
Keep these instructions for future reference
Image shown for reference only Image shown for reference only
Do not use to store glass or breakable items
Do not position pad over uneven grout lines
Not suitable for unfinished materials such as brick,
blockwork and loose, flaky surfaces
F
4. Important Note - The adhesive pad can only
be used once. It cannot be re-applied.
  • Page 1 1

Croydex QM380641YW Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI