Croydex QM370941YW Installation guide

Brand
Croydex
Model
QM370941YW
Category
Power plug adapters
Type
Installation guide

Croydex QM370941YW is a versatile storage product that can be mounted on walls using either a screw fix or suction fix method. It is ideal for storing a variety of items, such as toiletries, cleaning supplies, or kitchen utensils. The screw fix method is more permanent and suitable for heavier items, while the suction fix method is temporary and more suitable for lighter items. Both methods are easy to install and can be completed in just a few minutes.

Here are some of the key features and possible use cases of the Croydex QM370941YW:

  • Can be mounted on flat, shiny, glazed tiles or glass using either a screw fix or suction fix method

Croydex QM370941YW is a versatile storage product that can be mounted on walls using either a screw fix or suction fix method. It is ideal for storing a variety of items, such as toiletries, cleaning supplies, or kitchen utensils. The screw fix method is more permanent and suitable for heavier items, while the suction fix method is temporary and more suitable for lighter items. Both methods are easy to install and can be completed in just a few minutes.

Here are some of the key features and possible use cases of the Croydex QM370941YW:

  • Can be mounted on flat, shiny, glazed tiles or glass using either a screw fix or suction fix method
Assemble product as shown above.
Before placing in desired location
turn the caps (E) clockwise until
nger tight. Then turn the caps (E)
ve to six complete rotations
anti-clockwise as shown above.
Before installing
1.
Thoroughly clean the mounting surface to
remove any dirt, residue or contaminates
that may reduce the sucker performance.
2. Rinse the mounting surface with clean
water and dry with a clean cloth.
3. Rinse each suction bracket in warm water
to remove any dust etc. that may have
accumulated since manufacture, then dry
with a clean cloth.
Mounting your Twist ‘N’ Lock Plus Storage Product using the Suction Fix method
Component parts required
Holding the suction bracket body (C)
rmly pull the cap (E) away from
the body leaving a small gap
between the two parts.
2 3 4
Suction Fix Method
1
5
Keeping the gap between the body (C)
and the cap (E), position the product
in the desired location. Press the centre
of each cap (E) rmly closing the gap
between the cap (E) and body (C) to
expel air from the suction cups.
(A) Wire product
(B) Suction Cup
(C) Suction Bracket Body
(D) Spacer
(E) Cap
NOT ILLUSTRATED ITEMS
(F) Double End Fixing Screws (used only for
screw x method)
(G) Wall Plugs (used only for screw x method)
Content quantities vary depending on product purchased
E
B
A
D
C
Ensure the product is level and then
rotate the cap (E) clockwise until fully
tight. Your product is now ready to use.
It is possible to mount some wire baskets
in a corner. To do this dismantle the
suction bracket assembly by unscrewing
cap (E) fully and carefully unclip the
plastic spacer component (D) from the
body (C).
Reassemble the suction bracket as shown
and follow steps 1 to 4 to mount.
Loving your new Twist ‘N’ Lock Plus product? We have a wide range of bathroom accessories, please visit
www.croydex.com for more details.
How to remove your Twist ‘N’ Lock Plus product
Unscrew and remove the caps (E) while supporting the product.
Remove the product, the suction cups can then be peeled away from
the mounting surface.
Care and maintenance
Suction Fix is a temporary xing solution. For best performance we recommend
that you remove and re-t your product every 6 - 8 weeks as described above.
Clean with a soft damp cloth. Never use abrasive or chemical cleaners.
Croydex Limited, Central Way, Andover, Hants, SP10 5AW, UK
Tel: +44 (0) 1264 365881 Fax: +44 (0) 1264 356437
Website: www.croydex.com E-mail: [email protected]
Included in your pack
WARNINGS
•
Read these instructions carefully
•
Only x to at, shiny, glazed tiles or glass. Never use on
wood, painted, matt or textured surfaces. If tting to these
surfaces is required please refer to screw to wall xing method
•
Do not overload - maximum weight 2kg (4.5lbs)
•
Keep these instructions for future reference
•
Do not use to store glass or breakable items
•
Do not position sucker over grout lines
•
instruction leaet which is on the reverse of this sheet.
Not suitable for marble tiles.
TNL+005 R04
WARNINGS
Safety and care advice
1. Always take care when using an electric drill,
particularly in the bathroom. Always check for
hidden cables and pipework before drilling.
Always use a residual current circuit breaker
(RCCB) when using mains powered tools and
take extreme care if there is any water in the
working area.
2. Always wear suitable eye protection when drilling.
3. If the product is to be tted on a ceramic tiled
wall, a ceramic drill bit should be used. Do not
drill mounting holes in the grouted area between
tiles. Mask the area around the hole with tape
before drilling to prevent damage to the tile.
Mounting your Twist ‘N’ Lock Plus Storage Product using the Screw x method
Component parts requiredIncluded in your pack
1
Insert the wall plug (G) to the surface of
the wall. If tting to a tiled surface the
wall plug should be inserted below the
surface of the tile to avoid cracking.
Insert the double end xing screw (F)
into the wall plug up to the shoulder,
as shown.
2 3
Screw Fix Method
•
Read these instructions carefully
Do not overload - maximum weight 2kg (4.5lbs)
•
•
Keep these instructions for future reference
4
Ensure the product is level and
then rotate the cap (E) clockwise
until fully tight. DO NOT OVER
TIGHTEN!
Repeat for the other cap.
•
Wall plugs supplied for solid walls only.
Ensure correct wall plug for wall type is used.
C
G
A
E
Tools Required:
Drill; 6mm Masonry Drill Bit (6mm Ceramic Drill bit optional)
Cross Head Screwdriver; Pencil
(A) Wire product
(B) Suction Cup (discard for screw to wall xing)
(C) Suction Bracket Body
(D) Spacer
(E) Cap
(F) Double End Fixing Screws
(G) Wall Plugs
Wall plugs supplied for solid walls only. Ensure correct wall
plug for wall type is used.
C
F
D
5
It is possible to mount some wire baskets
in a corner. To do this dismantle the
suction bracket assembly by unscrewing
cap (E) fully and carefully unclip the
plastic spacer component (D) from the
body (C).
Reassemble the suction bracket as shown
and follow steps 1 to 4 to mount.
Loving your new Twist ‘N’ Lock Plus product? We have a wide range of bathroom accessories, please visit
www.croydex.com for more details.
How to remove your Twist ‘N’ Lock Plus product
Unscrew and remove the caps (E) while supporting the product.
Care and maintenance
Clean with a soft damp cloth. Never use abrasive or chemical cleaners.
Croydex Limited, Central Way, Andover, Hants, SP10 5AW, UK
Tel: +44 (0) 1264 365881 Fax: +44 (0) 1264 356437
Website: www.croydex.com E-mail: [email protected]
Content quantities vary depending on product purchased
With the caps (E) removed, place the
wire product (A) and body (C) assemblies
over the exposed shoulders of each
screw (F) and align caps (E) as shown.
TNL+005 R04
Select position of product and
mark centres of mounting holes.
Using a 6mm masonry drill, drill a hole
in the marked position to a depth of
50mm. If drilling through tiles, please
pre-drill using a ceramic drill bit.
  • Page 1 1

Croydex QM370941YW Installation guide

Brand
Croydex
Model
QM370941YW
Category
Power plug adapters
Type
Installation guide

Croydex QM370941YW is a versatile storage product that can be mounted on walls using either a screw fix or suction fix method. It is ideal for storing a variety of items, such as toiletries, cleaning supplies, or kitchen utensils. The screw fix method is more permanent and suitable for heavier items, while the suction fix method is temporary and more suitable for lighter items. Both methods are easy to install and can be completed in just a few minutes.

Here are some of the key features and possible use cases of the Croydex QM370941YW:

  • Can be mounted on flat, shiny, glazed tiles or glass using either a screw fix or suction fix method
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents