DreamLine SHDR-6548760-07 Installation guide

##=finish

07- Brushed Stainless Steel

08- Polished Stainless Steel

MODEL #s

SHDR-6548760-##

SHDR-6560760-##

MODEL #s

SHDR-6560620-##

ENIGMA SKY

SHOWER AND TUB DOOR INSTALLATION INSTRUCTIONS

IMPORTANT

DreamLine

®

reserves the right to alter, modify or redesign products at any time without prior notice.

For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer

to your model’s web page on DreamLine.com

For more information about DreamLine

®

Shower Doors, Tub Doors & Enclosures, please visit DreamLine.com

ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Right-hand door installation shown

ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

This model is treated with DreamLine’s

exclusive ClearMax

TM

Glass technology.

This is a specially formulated coating

that prevents the buildup of soap and

water spots.

Install the surface with the ClearMax

TM

label towards the inside of the shower.

Please note that depending on the

model, the glass may be coated on

either one or both surfaces.

For best results, squeegee the glass after

each use and dry with a soft cloth.

Detailed Diagram of Shower Door Components

Installation Steps

Parts List

Table of Contents

Section title

Page #

Tools

Preparation

Reinforcement

Troubleshooting and Maintenance tips

Vinyl Seals

Bumper Installation

Product maintenance

7

6

5

3

4

2

27

Maintenance Checklist

28

8-26

26

22-23

ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

NOTE: The right-hand door installation is shown as an example

throughout this manual. For the left-hand door installation, simply

begin on the opposite wall and reverse the orientation of the parts

in the steps shown.

Right-hand door installation Left-hand door installation

!

D

OOR

P

ANEL

D

OOR

P

ANEL

ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018 2

Install studs OR install 2”x 6” wood blocking between the studs where the

Guide Rail Brackets will attach to the wall

Reinforcement for Enigma Series

Heavy Glass frameless sliding shower or tub door

2” X 6”

Stud

or

threshold

or tub deck

measured

from threshold

or tub deck*

(see list below)

2” X 6”

*Blocking height requirement (to center)

as measured from threshold or tub deck:

Enigma Air, Enigma Sky = 73” for shower ht / 59” for tub ht

Enigma X, Enigma XO = 72-1/2“ for shower ht / 58-1/2” for tub ht

Enigma Z = 73-1/2” for shower ht / 59-1/2“ for tub ht

Enigma = 75-1/2” for shower ht only

threshold

or tub deck

3

ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Roller Wheels tight leaving the

proper clearance beneath the

door glass and guide block

Bottom Roller Wheels

adjusted to make

contact with the Guide

Rail

Guide block screwed down

and square with glass

*Stopper properly

positioned and tight

-door makes contact

with stopper and

bottom bumper

evenly when the door

is in the fully open

position

*Stopper properly positioned and

tight so that the Door stops against

the stopper and seals rmly into the

bumper inserts in the u-channel

Guide Rail level

To secure the Stoppers (#05):

Apply the Thread Lock adhesive to the

threads of the set screws during the nal

installation. Fully tighten the set screws with

the supplied allen wrench.

Stopper

Thread Lock Adhesive

Recommend to apply thread lock to:

• Stopper set screws

• Wheel bolts

• Glass Bracket bolts

ENIGMA-SKY

troubleshooting and

maintenance tips

The Roller wheels can be

adjusted as needed so

that door glass makes

even contact within the

u-channel from top to

bottom

Guide Rail bracket ush with

wall and set screws tight;

Installation into a

stud strongly recommended

Glass brackets

tight

Panel Glass sits ush

on the threshold

All rubber gaskets and sleeves installed properly between

all hardware and glass to prevent glass to metal contact

Guide Rail

bracket ush

with wall

and set

screws tight

Bumper

inserts

installed into

u-channel

Inspect bottom

corners of door glass

for damage.

**Units with

damaged door glass

should not be used

until door glass has

been replaced**

Right Hand door installation shown as an example

Handle tight

* Stopper Locations as measured from the

wall to the center of the stopper:

• Panel side: 5” (+/-) when the door

contacts the bottom bumper

• Door side: 3-1/2” (+/-) (depends on

opening conditions)

Rotate disk to adjust

Door Glass

Panel Glass

SafeStop™

Bumper is

secured in

position with

3M tape or

screwed to

the wall

Preparation

1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count

with the packing slip. After opening all boxes and packages read this introduction carefully. Check that all

of the necessary parts are included in the package by checking off the components on the “Detailed

Diagram of Shower Door Components”. If the unit has been damaged, has a finishing defect, or has

missing parts, please contact our customer support department within 3 business days of the delivery

date. Please note that DreamLine

®

will not replace any damaged products or missing parts free of

charge after 3 business days or if the product has been installed. Contact DreamLine

®

if you have any

questions, and please provide an order number, job name or other proof of purchase to help identify the

original order.

2. Please note that you should consult your local building codes with questions on installation

compliance standards. Building and plumbing codes may vary by location, and DreamLine

®

is not

responsible for code compliance standards for your project and will not accept any returns.

3. If this unit is going to be installed in a new construction, please install all of the required plumbing and

drainage before installing the shower. Use a competent and licensed (if required by local code) plumber

for all plumbing installation

4. Please make sure that prior to beginning the installation, the surfaces are leveled and solid and will be

able to support the total weight of the unit. Also make sure the walls are at right angles. Irregular

installation surface level, radius corners or improper angle of side walls will result in serious problems for

your installation. Note that some adjustments and drilling will be necessary during the installation process.

5. Please protect all primary surfaces of the product during installation. Never set the glass down directly

onto a tile floor. Leave corner protectors in place until necessary to remove them. Always use a piece of

wood or cardboard to protect the bottom edge and corners of the glass prior to and during installation.

6. This unit must be installed upon a finished threshold and against finished walls.

7. This model does NOT have any adjustment for out-of-plumb wall conditions. Verify that your walls are

plumb before proceeding with the installation.

8. This model requires that you drill into the threshold for proper installation.

9. Installation of the Guide Rail brackets into a stud or 2” x 6“ wood reinforcement is strongly

recommended. See Steps #8 and #19 for details.

10. This model requires a minumum of 2-1/4” of flat threshold space for installation.

11. Professional installation required.

NOTE: This manual will describe the shower door installation. Please follow the same sequence of

installation steps for the tub door installation.

NOTE: DO NOT attach the handle to the door glass until instructed.

DO NOT use the handle to lift the glass during installation. This may result in damage to the

glass and/or serious injury. Always use an assistant and/or a professional grade glass suction

cup when handling heavy glass panels.

4ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

!

Tools

Tip: Measure the finished opening before

proceeding with the installation to be sure

that the correct model size has been

ordered.

Tip: Prior to installation, cover the

shower/tub drain with tape to prevent

losing screws or small parts.

NOTE: Unpack your unit carefully and inspect it. Lay it out and identify all parts using the detailed

diagram and packing list in this manual as a reference. Before discarding the carton, check for small

hardware bags that may have fallen to the bottom of the box. If any parts are damaged or missing,

please contact DreamLine

®

for replacement. The shipping boxes may contain extra parts not used in

your model configuration.

NOTE: Retain these installation instructions for future reference.

Tip: Set screw gun clutch to low setting

when installing screws and bolts to

prevent stripping the heads.

5ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

W

Top

Middle

Bottom

Silicone

Tape

Measure

Level

Phillips

Screwdriver

Pencil

Carpenter’s Square

Drill

Power

Painter’s Tape

Hammer

Soft Head

Metal File

Chop saw and Hacksaw

Professional-grade

Glass suction cup

(Ø1/8")

(3mm)

Drill bit

(Ø5/16")

(8mm)

Drill bit

1/2” Shims

!

Threshold must be level.

Detailed Diagram of shower door components

6ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

The glass surface

with the ClearMax™

label must be

installed to face

inside of the shower

28

27

21

20

26

6a

6b

7

4

8

5

1

13

15

16

2

3

18

19

17

10

11

12

6

D

OOR

P

ANEL

Right-hand door installation shown

Parts List

7ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

4

ITEM #

5

6

DESCRIPTION

PART NUMBER

QTY

1set

Stationary glass

9PC

11PC

Guide Rail Bracket( 6a&6b)

Stopper

2

3

Countersunk screw ST4.2X40

07550045

092111

07121089

07021109

07121074

07021111

1

U-channel

5/16" plastic wall anchor

1PC

7

07021112

11

12

13

10

8

17

18

19

15

16

21

20

Door glass

Guide Rail

Glass Bracket

Roller

Threshold End Cap

Anti-splash Threshold

Guide Block

Anti-water side strip

Handle

Allen wrench ( 4mm)

Thread Lock Adhesive

Round head

screw ST4.2X25

1PC

2PCS

4PCS

1PC

2PCS

1PC

2PCS

07321023

07551068

07021110

063004100-1798

091104

092113

098004

010420012

160012

1PC

26

07021153

Bumper

010420001

/ 07124089

07024109

07124074

07024111

07024112

07324023

07554068

/

07024110

/

07024153

/

04100011-0638

/04100041-0638

28

27

U-channel

1PC

5PC

07550074

Insert Bumper

07121069

/ 07124069

Countersunk screw ST4.2X55

07221004 07224004

/

010420003

0104200

10

4876"

6076"

6062"

010420005

4876"

6076"

6062"

010420011

62"

76"

07121138

/ 07124138

62"

76"

07121137

/ 07124137

48"

60"

07121075

07124075

/

04100011-0790

/04100041-0790

48"

60"

Installation steps

8ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

!

Fig 2a

Fig 1

Bottom

Middle

Top

2-1/4 "

Minimum flat

threshold

space required

NOTE: This model requires a minimum

2-1/4” of flat threshold space for

installation.

W

2. Measure the finished opening width at the model height.

Use a Chop saw (with a blade for cutting stainless steel), to cut

the Guide Rail (#04) to fit the finished opening.

(Cut from the door end of the rail only)

◾for Shower model: Measure the width at a height of 72-1/4”

◾for Tub model: Measure the width at a height of 58-1/4”

This will be dimension (W).

The Guide Rail (#04) is 1“ less than the model size and will

need to be cut to 1” less than the finished opening size (W):

Finished opening (W) - 1” = finished cut length (L)

(Fig 2a and Fig 2b)

1. Check both nished walls to make sure they

are plumb and check the threshold to make

sure it is level across the opening. (Fig 1)

NOTE: This model does not allow for

out-of-plumb or out-of-level adjustment.

9ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

!

Fig 3

Finished opening (W) - 1” = finished cut length (L)

Cut from the door end only which

is the end opposite from the holes

(L)

door end

panel end

!

NOTE: Use a metal file to remove any burrs

from the cut end of the Guide Rail (#04).

Metal File

Fig 2b

1/8”

to 1/4”

_____________ Model size

_____________ -(minus) Finished opening (W)

_____________ = Finished cut length (L)

threshold

outside

3. Starting from the wall on the stationary panel side

of the finished opening, use a Carpenter’s Square as a

guide and measure in 1/8” -1/4” from the outside of

the threshold and mark the threshold. Extend this line

across the threshold to the opposite wall to use for

reference in Step #18. (Fig 3)

10ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

U-Channel

reference

mark

Fig 4

Fig 5

**NOTE: When installing to

a stud, drill a Ø1/4” hole and

do not use the anchors.

or Ø5/16"

Ø1/4"

2**

1

4

5

3**

4. Align the edge of the U-Channel (for Panel Glass) (#01)

to the inside of the reference mark on the threshold. Use a

level to hold the U-channel plumb and mark the position of

the U-Channel (for Panel Glass) (#01) on the wall.

Also mark the four holes for drilling through the pre-drilled

holes in the U-channel. (Fig 4)

5. Remove the U-Channel (for Panel Glass) (#01) from the wall, drill the anchor holes using a Ø5/16”

drill bit and insert the Ø5/16” Plastic Wall Anchors (#16) (**see Note below).

Apply a bead of silicone to the back of the U-Channel (for Panel Glass) (#01) and attach it to the wall

using four of the ST4.2 x 40 Round Head Screws (#17). (Fig 5)

11ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Fig 6c

outside outside

GUIDE RAIL BRACKET HEIGHT

MODEL

HEIGHT

H =

76"

shower 72-1/4"

62"

tub 58-1/4"

Table 1

Fig 6a

Fig 6b

Right-hand door installation shown as example

57-1/4”

(H)=

58-1/4”

1 1/4”

(H)=

72-1/4”

71-1/4”

1 1/4”

U-Channel

shower height

tub height

Guide Rail

Bracket

H

outside inside

u-channel

Guide Rail

Bracket

plumb line

1-1/4”

H

6. To position the Guide Rail Bracket (#06) on the

stationary panel side:

From inside the shower, measure up from the threshold

to the bottom of the Guide Rail Bracket (#06) using

Table 1 below. Hold the bracket in place 1-1/4” from the

outside of the U-channel (as shown in Fig 6a) and mark

the wall at the bottom of the bracket.

(Fig 6a and Fig 6b and Fig 6c)

12ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

!

*NOTE: Installation of the Guide Rail

brackets into a stud or 2”x 6” wood

reinforcement is strongly recommended.

**NOTE: When installing to a stud,

drill a Ø1/4” hole and do not use

the anchors.

Fig 8

#06b

#06a

The guide rail wall

bracket should be

centered in the

bracket as shown

to allow for vertical

adjustment both

up and down.

Note that the bottom of the

bracket is thicker than the top

and must be installed correctly

C

L

(=)

Fig 7

Ø5/16"

Ø1/4" or

1 * 2

3

top

bottom

!

7. Hold the Guide Rail Bracket (#06) in the

marked position on the wall and mark the hole for

drilling through the Guide Rail Bracket (#06)

using a pencil (or center punch). (Fig 7)

8. Drill a Ø5/16” anchor hole and insert a Wall Anchor (#16). (**See note below)

Separate the Guide Rail Bracket (#06) components (#06a and #06b). Install the Guide Rail Wall

Bracket (#06b) to the wall using one ST4.2 x 55mm Countersunk Screw (#21). (Fig 8)

13ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Use Caution not to bang the glass

into the U-Channel or threshold.

!

Use a professional grade

glass suction cup if available

Fig 9

Fig 10

2

1

3

10. Make sure the Stationary Panel Glass (#02) is parallel to the front edge of the threshold and mark

the position of the glass on the threshold (This line will be different from the line drawn in step#3).

Slide the Guide Block (#12) into the notch of the Stationary Panel Glass (#02), and align it flush and

square with the edge of the glass. Mark its position on the threshold and also mark the hole for drilling

using a pencil (or center punch). (Fig 10)

9. Dry fit the Stationary Panel Glass (#02) into the

installed U-Channel (For Panel Glass) (#01). Do not

use silicone at this time. (Fig 9)

14ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Fig 11

Fig 12

3

*see

note

2

use a pencil or

a center-punch

to mark the hole

**

only use anchor

with tile threshold

4

5

face plate

1

Part#12 - Guide Block (with caps)

M5 X 10

12. To install the Guide Block (#12): Loosen the set screw on

the side and remove the guide block face plate. (Fig 12.1)

Apply silicone to the underside of the Guide Block (#12) and

screw the Guide Block (#12) to the threshold as described

below:

*NOTE:

◾For installation into an Acrylic threshold:

◽drill an Ø1/8”(3mm) hole and use the ST4.2 x 25mm

Round Head Screw (#18)

OR

◾For installation into a Tile threshold:**

◽drill a Ø5/16”(8mm) hole, install Wall anchor 5/16” (#16)

and use the ST4.2 x 40mm Countersunk Screw (#17).

(Fig 12)

NOTE: For Tub installations: the bottom bracket must be

screwed down to the tub deck.

11. Remove the Stationary Panel Glass (#02)

from the U-Channel (For Panel Glass) (#01)

and carefully set it aside. (Fig 11)

15ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

top

bottom

Note that the panel side

stopper goes beyond the

first glass holder hole

Fig 13

13.

Apply silicone into the U-Channel (For Panel Glass) (#01).

Slide the Stationary Glass (#02) firmly into the installed

U-Channel (For Panel Glass) (#01). (Fig 13)

!

Fig 14

Right-hand door installation shown as example

1

2

3

4

door endpanel end

panel end

door end

Use Caution not to bang the glass

into the U-channel or threshold.

D

OOR

P

ANEL

!

14. Attach the Stoppers (#05) and Guide Rail Brackets (#06) to both ends of the Guide Rail (#04).

(Notice that the bottom of the Guide Rail Bracket (#06) is thicker than the top). (Fig 14)

NOTE: Be careful not to scratch the guide

rail with the brackets and stoppers. Loosen

the set screws before installation.

!

TIP: Bring the Door Glass into the shower before the final

installation of the Stationary Panel Glass (#02) and

Guide Rail (#04).

16ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

!

TIP: Leave the set screws that hold the Guide Rail (#04) to the Guide Rail Bracket (#06)

loose for now to allow for side-to-side adjustment of the guide rail to make it easier to align

the holes in the guide rail with the holes in the panel glass. Tighten these set screws after

the holes are aligned and the glass brackets are installed.

TIP: Pinch the Guide Rail and Panel glass

together to hold the washers in place

while inserting the bolt.

Fig 16

Fig 15

1 2

15. Align the panel end of the Guide Rail (#04) with the installed Guide Rail Wall Bracket (#6b).

Slide the Guide Rail Bracket (#06a) over the Guide Rail Wall Bracket (#06b) and tighten the set

screws. (Fig 15)

16. Attach the Stationary Panel Glass (#02) to the Guide Rail (#04) using the Glass Brackets (#07).

(Fig 16)

17ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Fig 17

Fig 18

!

1-1/4”

measure 1-1/4”

from the plumb

line to the edge

of the bracket

inside the

shower

with the guide

rail level, mark

the bottom

position of the

bracket on the

wall

1

-

1

/

4

”

1

2

NOTE: It is important that

the guide rail is level when

marking the position of the

Guide Rail bracket on the wall.

To lower the rail:

Loosen the top set screw and

tighten the bottom set screw.

To raise the rail:

Loosen the bottom set screw

and tighten the top set screw.

1-1/4”

18. Using the reference mark on the threshold from Step #3,

draw a plumb line up the wall on the door side of the

opening. Measure over 1-1/4” into the shower from this line.

With the Guide Rail (#04) level, mark the position of the

Guide Rail Bracket (#06) on the wall. (Fig 18)

17. Level the Guide Rail (#04) across the opening.

If necessary, use the set screws on the Guide Rail Bracket (#06)

to adjust the level of the Guide Rail (#04).

(Fig 17 and Fig 18)

18ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

*NOTE: Installation of the Guide Rail

brackets into a stud or 2”x 6” wood

reinforcement is strongly recommended.

Do not use the Wall Anchor (#16) when

installing into a stud/wood).

!

#06b

#06a

Fig 19

3*

2**

4

NOTE: Be careful not to scratch the upper rail while sliding the brackets onto the guide rail.

1

Fig 20

1

2

3

4

5

6

or Ø5/16"

Ø1/4"

**NOTE: When installing to a stud, drill a

Ø1/4” hole and do not use the anchors.

To lower the rail:

Loosen the top set

screw and tighten

the bottom set

screw.

To raise the rail:

Loosen the

bottom set screw

and tighten the

top set screw.

20. Re-attach the Guide Rail (#04) to the Stationary Panel Glass (#02) and attach the Guide Rail

Brackets (#06). (Fig 20)

19. Remove the Guide Rail (#04) from the Stationary Panel Glass (#02). Remove the Guide Rail

Bracket (#06) from the Guide Rail (#04) from the door end, hold it back in position on the wall and mark

the anchor hole. Drill a Ø5/16” hole. Separate the Guide Rail Bracket (#06) components (06a and 06b).

Attach the Guide Rail Wall Bracket (#06b) to the wall using one ST4.2 x 55mm Countersunk Screw

(#21). (Fig 19)

Page is loading ...

DreamLine SHDR-6548760-07 Installation guide

This manual is also suitable for

DreamLine SHDR-6548760-07 Installation guide

Related papers

Other documents