Installation Guide
Loading Paper
Before your machine will be ready to make
copies or receive faxes, you must load paper
into the machine. Use paper letter, 8.5 x 11
Inch (216 × 279 millimetres). Your machine
works with normal copier paper and with
typewriter paper (
0.13 – 0,2 lb
/m
2
) (see
user manual chapter Installation / Paper).
1 Separate the paper sheets by fanning
them out, then align them by tap-
ping edge of the stack lightly against
a fl at surface. is will prevent several
sheets of paper from being drawn in
all at once.
2 Remove the cover from the paper tray.
Put in only as much paper as will fi t
under the raised limit markers on the
upper edge of the paper input tray
(see also the drawings on the cover
of the paper input tray). You can load
up to 250 sheets into the paper input
tray.
Document Output
Tr ay
Insert the document output tray into the
two openings under the operation panel.
Document Input Tray
Insert the document input tray into the
two openings in the cover. e document
support should snap securely into place.
Paper Output Tray
Pull the paper output tray out of the paper
tray cover.
Document input tray
Document guide
Document feed slot
Operation panel
with LCD display
Document
output tray
Paper output tray
(extendable)
Paper input tray
Opening for
Plug’n’Print card
Cover
3 Press the paper down until the lever
(A) snaps into place at the rear of the
paper input tray.
4
Place the cover back on the paper input
tray. Push the paper input tray into the
machine all the way to the stopping point.
II
New Print Cartridge
1 Open the cover by taking hold of both document guides
and tipping the cover backward.
2 Take the new print cartridge from the package.
3 Remove the black protective paper and other packaging ma-
terial, but do not yet remove the protective strip from the
cartridge.
4 Shake the new print cartridge back and forth several times
in order to distribute the toner evenly, thereby improving
the print quality.
5 Only after removing the other packaging, completely
pull off the protection strip located on the left side of the
cartridge
Æ
Once you have removed the protection strip, do not
shake the print cartridge any more. Otherwise, it is
possible that toner dust will be released into the air.
6 Place the print cartridge into your machine. e cartridge
should snap securely into position.
7 Close the cover. Make sure that the cover snaps securely
into position on both sides.
¡
e toner level memory for this starter cartridge
was set at the factory. e starter cartridge need
not be updated with a Plug’n’Print card. For each ad-
ditional print cartridge that you insert into your ma-
chine, you must update the toner level memory with the
Plug’n’Print card provided.
III
Connecting the Telephone Cable
Connect the telephone cable to the machine by plugging it
into the outlet located on the rear side of the machine and
designated by the word LINE. Insert the telephone plug into
your PTT line outlet.
Quick Installation
Insert the power cord into the connection located on the rear
side of the machine. Connect the power cord to the electrical
outlet.
Once the machine is connected to the power supply, the
quick install process will immediately commence. You will
be asked to select your country and to enter your number
and name as well as the date and time (see user manual
chapter Settings).
Setting the Country
It is essential to select the country because otherwise your ma-
chine will not have the correct settings for the local telephone
network.
1 Select the country by pressing
[
or
]
.
2 Confi rm with OK.
Entering Your Telephone Number
and Name
1 Enter your fax number with the number keys, for exam-
ple,
00 44 123 45
… To enter a plus sign,
simultaneously press the CTRL key and Q. You may add
a space by pressing the
½
key. Confi rm your entry by
pressing OK.
2
Enter your name using the letter keyboard. To enter capi-
tal letters, press
+
and the desired key simultaneously. You
may add a space by pressing the
½
key. e symbols are
displayed directly above the letter keys. To enter symbols,
press the CTRL key and the corresponding letter key si-
multaneously. It is not possible to insert a symbol as the
fi rst character of your name. Confi rm with OK.
Entering Date and Time
1 Enter the date and time in the following manner:
08 08 05 14 00
for August 8th, 2005,
2:00 pm.
2 Confi rm with OK.
PC Connection
Æ
FIRST INSTALL THE SOFTWARE. e device
may not be connected to the PC before this. After
the software installation, the PC must be restarted, only
then should you connect your PC and the machine
with a USB cable.
Requirements
Your computer must meet the following minimum re-
quirements:
Processor:
500 MHz for Windows 98 SE®
800 MHz for Windows 2000 · ME®
1 GHz for Windows XP®
RAM:
128 MB for Windows 98 SE · 2000 · ME®
192 MB for Windows XP®
Operating System:
Windows 98 SE · 2000 · ME · XP®
Free Hard Drive Space:
260 MB of free hard drive space for installation of C-
S and P P.
USB Interface
IV
You can connect your machine only to a PC (Microsoft Win-
dows® operating system). e machine is not compatible with
Linux or Apple Macintosh®.
Installing the Software
On the installation CD included with your machine, you will
fi nd the C Se and P P. With the C-
Se, you can access the address book of the machine
from your computer and add or edit entries. You can also alter
your machine settings as well as checking the toner level of the
print cartridge. With P P, you can scan and manage
documents.
e machine is registered as the default printer on your com-
puter. You can access it as you would any other printer and use
it to create black-and-white print-outs.
Close all open programs and applications before beginning the
installation process. Place the installation CD in the CD-ROM
drive of your computer. e program will start automatically.
(If the program does not start automatically, select the CD-
ROM drive in the Windows® Explorer and start the program
S. with a double-click.)
251588732-A NA EN (FaxCentre F110)
/