3) GENERAL INSTALLATION
Install the mounting brackets to the side of the XM5 using the supplied screws.
iConverter XM5 NIDs with mounting bracket
Removeanyrubberfeetbeforeinstallingthemodule/chassistotheshelf.
4) INSTALLING ICONVERTER XM5 NIDS TO THE SHELF
Slide the XM5 into the mounting guide slots on the shelf.
Installing iConverter XM5 NIDs on the Shelf
ContinuetoslidetheXM5untilitisushwiththefrontmountbracketontheshelf.Secure
the XM5 by fastening the thumbscrew (push in and turn clockwise to tighten) to the shelf.
XM5 NIDs Installed in the Shelf
Embedded cable tie down slots secure the power cord(s) and data cable(s) totheshelf
(cable ties not included).
Page 2 Page 3
General and Copyright Notice
Thispublicationisprotected byU.S. andinternational copyrightlaws.All rightsreserved.The
whole or any part of this publication may not be reproduced, stored in a retrieval system,
translated, transcribed, or transmitted, in any form, or by any means, manual, electric, electronic,
electromagnetic,mechanical,chemical,opticalorotherwise,withoutpriorexplicitwrittenpermission
of Omnitron Systems Technology, Inc.
The following trademarks are owned by Omnitron Systems Technology, Inc.: FlexPoint
TM
,
HybridNID
®
, iConverter
®
, miConverter
TM
, NetOutlook
®
, OmniLight
TM
, OmniConverter
TM
, Omnitron
Systems Technology, Inc.
TM
, OST
TM
and the Omnitron logo.
Allothercompanyorproductnamesmaybetrademarksoftheirrespectiveowners.
The information contained in this publication is subject to change without notice. Omnitron Systems
Technology, Inc. is not responsible for any inadvertent errors.
Warranty
This product is warranted to the original purchaser against defects in material and workmanship
foraperiodoftwo(2)yearsfromthedateofshipment.ALIFETIMEwarrantymaybeobtainedby
theoriginalpurchaserbyregisteringthisproductwithinninety(90)daysfromthedateofshipment
atwww.omnitron-systems.com/support.Duringthewarrantyperiod,Omnitronwill,atitsoption,
repair or replace a product which is proven to be defective with the same product or with a product
with at least the same functionality.
For warrantyservice, the product must be sent toan Omnitron designated facility, at Buyer’s
expense.OmnitronwillpaytheshippingchargetoreturntheproducttoBuyer’sdesignatedUS
addressusingOmnitron’sstandardshippingmethod.
Limitation of Warranty
Theforegoingwarrantyshallnotapplytodefectsresultingfromimproperorinadequateuseand/
ormaintenanceoftheequipmentbyBuyer,Buyer-suppliedequipment,Buyer-suppliedinterfacing,
unauthorizedmodicationsortamperingwithequipment(includingremovalofequipmentcoverby
personnelnotspecicallyauthorizedandcertiedbyOmnitron),ormisuse,oroperatingoutsidethe
environmentalspecicationoftheproduct(includingbutnotlimitedtovoltage,ambienttemperature,
radiation, unusual dust, etc.), or improper site preparation or maintenance.
Nootherwarrantyisexpressedorimplied.Omnitronspecicallydisclaimstheimpliedwarranties
ofmerchantabilityandtnessforanyparticularpurpose.
TheremediesprovidedhereinaretheBuyer’ssoleandexclusiveremedies.Omnitronshallnot
be liable for any direct, indirect, special, incidental, or consequential damages, whether based on
contract, tort, or any legal theory.
Environmental Notices
TheequipmentcoveredbythismanualmustbedisposedofinaccordancewithDirective2002/96/
EC of the European Parliament and of the council of 27 January 2003 on waste electrical
and electronic equipment (WEEE). Such disposal must follow national legislation for IT and
TelecommunicationequipmentinaccordancewiththeWEEEdirective:(a)Donotdisposewaste
equipment with unsorted municipal and household waste. (b) Collect equipment waste separately.
(c) Return equipment using collection method agreed with Omnitron.
The equipment ismarkedwith the WEEE symbol shown to indicate that it must be
collected separately from other types of waste. In case of small items the symbol may
be printed only on the packaging or in this manual. If you have questions regarding the
correct disposal ofequipmentgo to www.omniton-systems.com/support or e-mail to
©2015OmnitronSystemsTechnology,Inc.