Zebra AA18298-102A Owner's manual

Brand: Zebra

Model: AA18298-102A

Type: Owner's manual

AA18294-102 rev. A

August, 2006

Safety and Regulatory

Information for the

ZebraNet

PS 4000 Print Server

PS 4000 Print Server Safety Guide pg. 2

Power Supply Safety

Caution • Use the Correct Zebra Power Supply

Do not use the PS 4000 Print Server with any power supply other than

the one supplied with the product, or with the Zebra Technologies

Model LA-24 Battery Pack and its charger power supply.

If you are using the LA-24 Battery Pack to run the server, follow the

safety and usage guide provided with the Battery Pack.

Use of any power supply not approved speciﬁcally by Zebra for use

with the PS 4000 Print Server could cause damage to the server and

will void the warranty.

Caution • Ensure Correct A.C. Compatibility

• Ensure that the PS 4000 Power Supply is conﬁgured with the correct

A.C. mains adapter for the intended country of use that or the LA-24

Charger Power Supply is supplied with the proper A.C. power cord for

the intended country of use .

• Either Power Supply must be plugged into a properly grounded A.C.

outlet.

Important • Charger Power Supply Location

• Use care in locating the Power Supply. Never locate the power sup-

ply near any source of combustible material. Do not place it in loca-

tions where liquids or metallic objects may be dropped into the Power

Supply.

• Ensure the Power Supply has adequate ventilation.

Important • Indoor Use Only

The Power Supply shipped with the PS 4000 Print Server is intended

for indoor use only.

Important • Power Supply Maintenance

• Clean only with a dry or slightly damp, lint free cloth.

• Never operate a Power Supply that has been damaged in any way.

• Do not disassemble the Power Supply. There are no user serviceable

components inside.

Print Server Safety

Caution • Secure the Print Server Properly

• Use the mounting bracket supplied with the Print Server to secure it in

place.

• Locate the server where its installation will not interfere with normal

movement of personnel.

• Ensure that all cabling connecting the Print Server and the power sup-

ply are properly secured so that they will not present a hazard to per-

sonnel movement.

• Do not disassemble the Print Server. There are no user serviceable

components inside..

Important Safety and Regulatory Information

for the PS 4000 Print Server

Keep this Guide readily accessible. It contains important

safety information.

pg. 3 PS 4000 Print Server Safety Guide

Important • Indoor Use Only

The PS 4000 Print Server is intended for indoor use only.

Important • Use Only With Zebra Printers

The PS 4000 Print Server is intended for use only with Zebra printers.

Use of this server with printers not speciﬁed by Zebra may result in un-

reliable performance. Zebra will not provide technical support for this

product with use with third party printers.

Important • Use Only Zebra Cables

If using the server in conjuntion with the LA-24 Battery Pack, only use

the cables speciﬁed by Zebra to connect this battery pack to the server

and to supply power to any printers or ancillary equipment. Failure to

do so will void the warranty and could cause damage to any equipment

so connected.

Radio Regulatory Information

PS 4000 Using the 802.11g Radio

The following section only applies when the 802.11g radio

(with FCC ID: I28MD-ZLAN11G) is installed in a PS 4000 Print Server. The

antenna used for this transmitter must not be co-located or must not operate in

conjunction with any other antenna.

Caution • The PS4000 print server contains a Radio Frequency

transmitter. To ensure compliance with the FCC’s rules for Radio

Frequency Exposure a minimum separation distance of 8 inches

(20 cm) must be maintained between this device and all persons

during device operations. If this minimum distance cannot be

maintained then exposure to RF levels that exceed the FCC’s limits

may result..

European Regulatory Information for this Radio

AT BE CY CZ DK

EE FI FR DE GR

HU IE IT LV LT

LU MT NL PL PT

SK SI ES SE GB

Note: -Member states in the EU with restrictive use for this device are crossed out!

This device is also authorized for use in all EFTA member states (CH, IS, LI, NO)

Europe – EU Declaration of Conformity

This device complies with the essential requirements of the R&TTE Directive 1999/5/

EC. The following test methods have been applied in order to prove presumption of

compliance with the R&TTE Directive 1999/5/EC:

• EN55022:1998

European Emissions Standard

• EN 60950: 2000

continued

Important Notice:

This device is a portable RF printer intended

for commercial and industrial use in all EU

and EFTA member states except in France

where restrictive use applies.

Safety of Information Technology Equipment

• EN 300 328-2 V1.2.1 (2001-12)

Technical requirements for spread-spectrum radio equipment

• EN 301 489-17 V1.2.1 (2002-08)

EMC requirements for spread-spectrum radio equipment.

This device is a 2.4 GHz wireless LAN transceiver, intended for indoor home and ofﬁce

use in all EU and EFTA member states, except in France where restrictive use applies.

The use of this frequency band in France is subject to restrictions. You may only use

channels 10 and 11 (2457 and 2462 MHz) on French territory, except in those French

departments as listed in the table below where channels 1-13 (2412-2472 MHz) may be

used. For more information see http://www.anfr.fr/ and/or http://www.art-telecom.fr

Ain 36

Indre

69 Rhone

02 Aisne 37 Indre et Loire 70 Haute Saone

03 Allier 39 Jura 71 Saone et Loire

05 Hautes Alpes 41 Loir et Cher 72 Sarthe

08 Ardennes 42 Loire 75 Paris

09 Ariege 45 Loiret 77 Seine et Marne

10 Aube 50 Manche 78 Yvelines

11 Aude 54 Meurthe et Moselle 79 Deux Sievres

12 Aveyron 55 Meuse 82 Tarn et Garonne

16 Charente 57 Moselle 84 Vaucluse

19 Correze 58 Nievre 86 Vienne

2A Corse Sud 59 Nord 88 Vosges

2B Haute Corse 60 Oise 89 Yonne

21 Cote dʼOr 61 Orne 90 Territoire de Belfort

24 Dordogne 63 Puy de Dome 91 Essonne

25 Doubs 64 Pyrenees Atlantique 92 Hauts de Seine

26 Drome 65 Hautes Pyrenees 93 Seine St Denis

27 Eure 66 Pyrenees Orientales 94 Val de Marne

32 Gers 67 Bas Rhin

Ille et Vilaine 68

Haute Rhin

Zebra Technologies International, LLC

333 Corporate Woods Parkway

Vernon Hills, Illinois 60061-3109 USA

Phone: +1.847.634.6700 or +1.800.423.0422

Fax: +1.847.913.8766

Zebra Technologies Europe Limited

Zebra House

The Valley Centre, Gordon Road

High Wycombe, Buckinghamshire HP13 6EQ,

Phone: +44.1494.472872

Fax: +44.1494.450103

Zebra AA18298-102A Owner's manual

Zebra AA18298-102A Owner's manual

Zebra AA18298-102A Owner's manual

Related papers

Other documents