anovafurnishings.com
888.535.5005 tel
TOOLS NEEDED: HARDWARE NEEDED:
Installation Instructions
Beacon Hill Receptacles
Step-by-Step Installation Sequence
Product ships fully assembled.
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a
3,000 psi minimum and be cured for at least 28 days prior to the installation of the receptacle.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
!
(4) 3/8" x 5" 18-8
Stainless Steel Stud Anchors
92188A203
Optional: (4) 3/8"
Rubber Washers
90130A050Hammer Drill
Masonry Drill Bit Set
3/16", and 3/8"
Hammer
Pencil
9/16"Wrench
Wire Brush
Level
Safety Glasses
Installation Instructions
Step-by-Step Installation Sequence
Beacon Hill Receptacles
1.
2.
3.
5.
4.
Place receptacle in the desired location. Mark the location of the holes with
a pencil. To verify the alignment of the anchor markings you may reference
page 3.
It is recommended that you start holes in sequential order from the
smaller to the larger drill bits to avoid oversized holes or holes drilled too
deep. Begin with a 3/16" diameter drill bit followed by a 3/8" diameter bit.
Evacuate debris from mounting holes using compressed air and a steel wire
brush. This will create a clean environment for the anchor system.
!
2
5
4
Locate an anchor and adjust the nut so it is ush with the top of the anchor to
protect the threads from being damaged. Insert the anchor into the hole.
Use the hammer to x the anchor into the drilled hole by giving it several
hammer blows.
6.
7.
Repeat steps 2 - 5 until all anchors are installed.
Remove the nuts and washers o of the anchors. Align the mounting holes of
the receptacle over top of the anchors and slide it down into place.
8.
!
7
8.1 8.2
Care should be given to avoid rubbing the powder coating o the base.
A 3/8" rubber washer is a suitable replacement option. Mount the receptacle
to the ground by placing a washer and a nut onto each anchor. Leave the
hardware nger tight until all of them have been installed. Verify that the
receptacle is level before tightening the anchors. Tighten all of the hardware
with a 9/16" wrench.
12/31/2018 Copyright 2019 ANOVA® Manufactured in the U.S.
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
Installation Instructions
FOOT MOUNTS:
Beacon Hill Receptacles
SECTION A-A
SCALE 1:12
SECTION B-B
SCALE 1 / 12
A A
B B
1
1
2
2
3
3
4
4
A A
B B
THIRD ANGLE PROJECTION
TOLERANCES UNLESS NOTED:
X
1 X.X
.5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX
.015625 ANGULAR ± 1°
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90 UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125 .0625 DURING COATING.
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
specify@anovafurnishings.com
anovafurnishings.com
DRAWN
70 GALLON BONNET TOP RECEPTACLE
SIZE
B
BH1870BBT_SPEC-REV-002
DATE 4/1/2014 SCALE
.09375:1 SHEET
DWG NO
TITLE
B. MENDEZ
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
REV
1
OF
002
1
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
REV DESCRIPTION ECN TR.# DATE
001 ORIGINAL PRINT NONE 4/1/14
002 ASDDED MOUNTING PLATE VIEW NONE 12/28/18
NOTES:
31.51"
35.12"
39.74"
36.25" 7.24" 15.41"
41.50"
3.50"
13.10"
30.32"
38.44"
11.32" 22.50"
15.5625"
(4 PLCS)
6.0625"
(4 PLCS) .50"
(4 PLCS)
Ø.50"
(4 PLCS)
15.5625"
(4 PLCS)
6.0625"
(4 PLCS)
SECTION A-A
SCALE 0.11 : 1
A A
1
1
2
2
3
3
4
4
A A
B B
THIRD ANGLE PROJECTION
TOLERANCES UNLESS NOTED:
X 1 X.X .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX .015625 ANGULAR ± 1°
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125
.0625 DURING COATING.
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
specify@anovafurnishings.com
anovafurnishings.com
DRAWN
45 GALLON PLANTER
SIZE
BBH1845B_SPEC-003
DATE
4/1/2014
SCALE
1:10
SHEET
DWG NO
TITLE
B. MENDEZ
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
REV
1
OF
002
1
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
REV DESCRIPTION ECN TR.# DATE
001 ORIGINAL PRINT NONE 4/1/14
002 OPEN TOP SIZE CHANGED NONE 12/15/14
003 ADDED MOUNTING PLATE VIEW NONE 12/28/18
NOTES:
35.01"
3.50"
24.00"
12.82"
20.94"
24.00"
6.825"
(4 PLCS)
6.825"
(4 PLCS)
.50"
(4 PLCS)
Ø.50"
(4 PLCS)
6.825"
(4 PLCS)
6.825"
(4 PLCS)
SECTION A-A
SCALE 0.06 : 1
AA
1
1
2
2
A A
B B
1
???
OF
BH1835R
1
REV
SHEET0.06 : 1
SCALE
DATE
4/17/2018
DWG NO
TITLE
A
DRAWN
D. METZ
SIZE
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125 .0625 DURING COATING.
TOLERANCES UNLESS NOTED:
X
1 X.X
.5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX
.015625 ANGULAR ± 1°
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
specify@anovafurnishings.com
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
REV DESCRIPTION DATE
??? ???? ??/??/13
NOTES:
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
6.0625
(4 PLCS)
6.0625
(4 PLCS)
.5000
(4 PLCS)
6.0625"
(4 PLCS)
6.0625"
(4 PLCS)
Ø.50"
(4 PLCS)
35 Gallon Receptacles
45 Gallon Receptacles
70 Gallon Receptacles
/
