Küppersbusch EKE 606.3 Instructions For Use And Installation Instructions

Brand: Küppersbusch

Model: EKE 606.3

Type: Instructions For Use And Installation Instructions

BEDIENUNGSANWEISUNG

mit Montageanweisungen

Instructions for use and installation instructions

Instructions d’utilisation et avis de montage

Gebruiksaanwijzing en montagehandleiding

Istruzioni di uso e di montaggio

Instrucciones de uso y de montaje

Instruções de uso e de montagem

Ðtv³wuÒ xvÒvÒ ÊËw Ò´ÎËxÑÐÌÐ³vÒvÒ

EKE 805.3 / 606.3

241070 L21

Downloaded from www.Manualslib.com manuals search engine

EKE 805.3/606.3 13

Conditions of guarantee

The conditions of guarantee applicable for this product are subject to those

published by the representative in the relevant country. Details regarding same

may be obtained from the dealer from whom the appliance was purchased.

For claims under guarantee the sales receipt must be produced.

For your information

Please read the instructions in this booklet carefully as it contains important

information concerning the safety, the installation, the use and the mainte-

nance of your appliance.

The appliance should only be used for cooking in the household.

Keep the operation instructions in a safe place.

Notes on disposal

Disposing of the packaging

The transport packaging consists of the following materials: Corrugated card-

board, cardboard, styrofoam (CFC-free), Polyethylen-foil.

Do not put these materials in the household rubbish, but ask your local au-

thority to give you the adress of the most convenient collection point.

What to do if you happen to have an old appliance

Old appliances contain many materials which can be recycled. For this reason

you should not simply put your old appliance on the rubbish tip, but ask your

local authority how it might be recycled.

Contents

Your appliance at a glance . . . . . . . . . . . . . . . . . . . . . . . 14

Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

for connection and function

for the cooking area

Before first use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Use of the cooking zones . . . . . . . . . . . . . . . . . . . . . . . . 16

Switch on the cooking area

The pan recognition function

The cooking setting

The automatic boost function

Cooking zone heating indicator

Some instructions on cookware

Dual-circuit cooking zones and frying zones

The emergency switch

Child proof lock (sensor-lock)

Minute minder

Switch off function

Warming zone

Time limit function (holiday function)

Other functions

What to do if there is a fault . . . . . . . . . . . . . . . . . . . . . . 20

Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Please note

Notes for fitting

Installation of glass-ceramic cooking areas

Electrical connection

Downloaded from www.Manualslib.com manuals search engine

14 EKE 805.3/606.3

Your appliance at a glance

1 Cooking zone with automatic switch off

(function (via minute minder)

2 Cooking zone thermal indicator

3 Dual-circuitcooking zone

4 Display for minute minder

5 Off-sensor / emergency switch

6 Child proof lock (sensor-lock)

7Sensor-stand-by switch

8 Minute minder

9 Sensor buttons for cooking settings

10 Sensor buttons for warming zone

11 Indicator for warming zone

12 Warming zone

13 Frying zone

Downloaded from www.Manualslib.com manuals search engine

EKE 805.3/606.3 15

Safety instructions

for connection and function

■ KÜPPERSBUSCH built-in cooking zones may be combined only with KÜP-

PERSBUSCH built-in ovens with cooling fan. The use of any other make of

oven shall exempt Küppersbusch from all liability. Failure to observe this re-

quirement will invalidate all granted certificates and labels of approval.

■ The mains connection, maintenance and repair jobs should only be carried

out by an authorised technician in accordance with the applicable safety

standards. Work which has been improperly carried out can endanger your

safety.

■ The surfaces of heating- and cooking zones become hot during operation.

Therefore: Always keep children away.

■ The appliance must be earthed!

for the cooking area

■ Overheated fats and oils may spontaneously ignite. You should therefore

cook food involving the use of fats and oils, e. g. chipped potatoes, only

under supervision. Never extinguish fats or oils with water! Place a lid on

the pan, switch off the cooking zone and take the pan off the hot cooking

zone.

■ If cracks, fractures, or any other defects appear in your glass-ceramic cook-

ing area, do not use your appliance. Unplug or otherwise disconnect your

appliance from the mains supply and call our service centre.

■ If the cooking area cannot be switched off due to a defect in the sensor

control immediately disconnect your appliance and call the service centre.

■ Immediately switch off the cooking zone after using with the respective mi-

nus key and not just by pot recognition.

■ Be careful when working with additional appliances! The connection leads

must not come into contact with the hot cooking zones.

■ The glass ceramic cooking area should not be used as a storage area.

■ Do not place combustible or inflammable objects upon the cooking top

which might be dangerous in case of unintentional switching on.

■ Do not place any inflammable or combustible items on the hob since there

is a risk of burns or damage if the hob is switched on unintentionally.

■ Never use the cooking zones without cookware. Never use the appliance to

heat rooms!

■ Never put aluminium foil or plastic on top of the cooking zones. Substances

that melt, for example plastic, foils and especially sugar and food with a

high sugar content are to be kept away from the hot cooking zone. In order

to avoid damaging, sugar, while still hot, should immediately be scraped off

the cooking area with a scraper.

■ Avoid repeated burning of stains and boiling over.

■ Chalk deposits may damage the cooking area.

■ If you have pets in your flat, who might reach the cooking top, activate the

child-proof unit.

Before first use

■ Remove packaging and moving parts.

■ Before first use the cooking area should be cleaned with a damp cloth and

a little washing-up liquid.

■ The cooking area is insensitive to temperature shocks (cold and hot) and

also extremely robust.

■ Avoid dropping sharp objects onto the cooking area. Pointed objects falling

onto your cooking area might break it.

■ Please read through the cleaning and care instructions. Be especially careful

to keep the sensor keys clean since soiling could be mistaken for finger

contact by the appliance. Never put anything (pans, tea towels etc.) onto

the sensor keys! If food boils over onto the sensor keys, we advice you to

activate the emergency switch.

■ You might hear a humming sound from the heating when switching on the

appliance. This is due to technical reasons and has no influence on quality

and functioning of your appliance.

■ Hot pans should not cover the the sensor keys, otherwise the appliance

switches itself off automatically.

■ If the electronic components heat up, a cooling fan switches itself on. This

cooling fan may continue to be in operation even after switching off the

cooking area.

Downloaded from www.Manualslib.com manuals search engine

16 EKE 805.3/606.3

Use of the cooking zones

Read the safety instructions!

Switch on the cooking area

Press the sensor-button for approx.

2 seconds. The LED-display above

the sensor lights up and the appli-

ance is in operation (stand-by

mode).

The stand-by mode automatically switches itself off,

– if you do not press another sensor key during the following 20 seconds

(after 10 seconds an acustic signal indicates that the appliance switches

itself off after another 10 seconds) or

– if the appliance is not used 10 minutes after starting operation.

The pan recognition function

The appliance is equipped with a pan recognition function.

If a suitable pan is put onto the

cooking zone, "U" is indicated by

the display.

If no pan or an unsuitable pan is put

onto the cooking zone, an under-

lined "U" is indicated.

After 10 minutes the cooking zone automatically switches itself off.

Should a "U" happen to appear in the display although there is no pan on the

cooking zone, this does not mean that a fault has occured. Nor does it mean

that the cooking zone will switch on automatically. The electronics adjust au-

tomatically, which means that this effect will not occur the next time the ap-

pliance is put into operation.

Switching off the pan recognition function

Press the plus- and minus-sensor at

the same time before making the

cooking setting.

A circle will appear in the display

next to the selected cooking setting.

There is a defect in the pan recog-

nition function, if this circle lights

up.

You can nevertheless continue to

use the cooking zone.

The cooking setting

You have 9 cooking settings availa-

ble.

Select the required cooking setting

with the plus- or minus-sensor.

It will be indicated in the display.

The "0"-position will not be indicat-

ed.

When pressing the plus-sensor the

cooking zone starts at cooking set-

ting 5, without boost.

When pressing the minus sensor

the cooking zone starts at cooking

setting 9.

This automatically starts the auto-

matic boost.

Switching off the cooking zone:

press the plus- and minus-sensor at

the same time.

and

Cooking setting suitable for

1-3 Heating, Warming,

Creeing, Defrosting

4-5 Steaming, Poaching,

Boiling

6-8 Roasting, Deep-frying

9Heating large quantities

and

Downloaded from www.Manualslib.com manuals search engine

EKE 805.3/606.3 17

The automatic boost function

All cooking zones are equipped with an automatic boost function. Maximum

power is used for the boost. The time period of the boost depends on the

selected cooking setting. After the elapsed time the cooking zone automatically

switches back to the selected cooking setting.

When selecting the respective cook-

ing setting by pressing the minus-

sensor, the boost function switches

on automatically.

During automatic operation a "A"

lights up in the display alternately

with the selected cooking setting.

When selecting the required cook-

ing setting by pressing the plus-

sensor, it is necessary to press the

plus-sensor again after reaching

cooking setting 9 if the automatic

boost function is to be activated.

Select the required cooking setting.

"A" lights up in the display alter-

nately with the selected cooking

setting.

Cooking zone heating indicator (1) (Example)

Lights up, as long as the cooking zones are still hot – even after switching off.

Be careful! The indicator can fail (defective lamp). In this case there is no

warning of hot temperature. Change lamp immediately.

Some instructions on cookware

Only use pans with even and flat bottoms.

Uneven pan bottoms prolong the boost times and increase the power require-

ment. Rough pan bottoms scratch the glass-ceramic area when shifted about.

When using fireproof glass or porcelain cookware, please follow the manufac-

turers instructions.

Choose a pan with a diameter at least as large as the cooking zone.

You will thereby save energy and cooking time. You will also avoid overheating

of the cooking area.

Wherever possible, place a lid on the pan.

You will save a lot of energy by cooking in a closed pan. Liquids and foods

will only boil over if the temperature is too high. For the cooking zones, you

can precisely set the temperature required. With a little practice, you will read-

ily make the correct choice of cooking settings so that nothing boils over even

when a lid is in place.

Dual-circuit cooking zones and frying zones

Usually the cooking zone with the smaller diameter is being heated.

Switch on the outer cooking zone circuit for bigger sauce pans or frying pans.

Press the cooking zone symbol next

to the plus/minus sensor. A control

indicator above the cooking zone

symbol indicates operation of the

dual-circuit cooking zone.

Pressing the cooking zone symbol

once again deactivates the dual cir-

cuit cooking zone or frying zone.

press again

Downloaded from www.Manualslib.com manuals search engine

18 EKE 805.3/606.3

The emergency switch

All functions can be switched off by pressing any of the two sensors to the

far right and the far left.

Even if you cannot reach an offsensor, the appliance can be switched off.

Child proof lock (sensor-lock)

Operating the sensor lock detains unauthorised persons from using the appli-

ance. In order to activate this lock the cooking area has to be in operation.

Press the sensor lock. It is alos

possible to press it during opera-

tion.

In this case you can only chosse a

lower cooking setting or switch off.

The lock is indicated by 3 flashing control indicators.

Be careful: Switching off the cooking area does not deactivate the lock!

Deactivating the lock:

Press the sensors under the flashing control indicators at once.

You can deactivate the lock as follows:

Press the sensors under the two left flasing control indicators at once. After

not more than 3 seconds press the sensor under the flashing control indicator

on the right.

Minute minder

The minute minder is equipped with a sleep-/and a switch-off function for a

maximum interval of 99 minutes.

You can activate the minute mind-

er by pressing the plus or the mi-

nus-sensor.

You can then select the required

period of time with the plus-sensor

(starting at 0) and the minus-sen-

sor (starting at 99).

An audible signal sounds for about

30 seconds when the time has

elapsed.

"00" is displayed.

The audible tone goes off when

pressing the plus- and the minus-

sensor at the same time.

Switch off function

An audible signal sounds for ap-

prox. 30 seconds when the time

has elapsed.

"00" is displayed.

Press the plus- and the minus-

sensor at the same time in order to

switch off the audible tone.

Press at once

after max. 3 sec.At once,

30 sec.

and

By pressing the clock-sensor next to the cooking zone sensor of

the left cooking zone at the back the cooking zone automatically

switches into minute minder function – the cooking zone is switched

off automatically when the set time is elapsed.

30 sec.

and

Downloaded from www.Manualslib.com manuals search engine

EKE 805.3/606.3 19

Warming zone (only EKE 805.3)

Switching the warming zone into stand-by mode

Press the sensor key. The LED-Display underneath the sensor lights up. If no

sensor is pressed in the following 4 seconds, the stand-by mode switches off

automatically.

Switching on the warming zone

Press the on-sensor. The LED-Display underneath the sensor lights up.

The former display goes off.

If the warming zone is still hot the heating indicator – flashes even after

switching off the appliance.

Be careful! The lighting can fail (lamp is defective). In this case there is no

warning of high temperatures. Change lamp immediately.

Switching off the warming zone

Press the off-sensor. Die LED-Display underneath the sensor goes off. The

warming zone is switched off automatically.

In order to switch on the warming zone once more you have to switch it into

stand-by mode first.

Time limit function (holiday function)

The appliance is equipped with an automatic time limit function. This function

makes sure that the appliance is not in operation for a long time. The time

period of the time limit depends on the selected cooking setting, eg.:

The higher the selected cooking setting, the faster the appliance is switched

off.

If more than one cooking zone is activated the maximum operation time de-

pends on the cooking zone with the highest cooking setting.

Other functions

■ If pressing two or more sensor keys – at the same time e. g. when a pan

is mistakenly put onto the sensor key no function is activated. An audible

signal sounds after 10 seconds. The appliance switches off automatically

after 20 seconds.

Exceptions:

– Deactivation of the sensor-lock

– Deactivation of the pan recognition function

– Switching off the cooking zones

– Switching off the audible signal

■ If you continue to press a sensor button even after having set the highest

cooking setting, an audible signal sounds after 10 seconds. After 20 sec-

onds the appliance switches off automatically.

■ In case of a break down of the mains supply the appliance does not auto-

matically switch on again.

■ In case of the electronic components overheating, – e. g. when a hot pan

was mistakenly put onto the sensor keys – the appliance switches off au-

tomatically.

In this case the control indicator above the left or the right emergency

switch flashes until the appliance has cooled down. Afterwards the cooking

area can be operated again.

Symbol for the warming zone Cooking setting Switching off time after

91 hour

82 hours

63 hours

54 hours

35 hours

110 hours

...

Downloaded from www.Manualslib.com manuals search engine

20 EKE 805.3/606.3

What to do if there is a fault

Unplug the appliance befor repair!

Check carefully to make sure that the fault is not due to misoperation. You

can rectify many faults yourself.

Important note:

Repairs should only be carried out by an authorised technician!

Even during the guarantee period repairs will not be free of charge if due to

incorrect operation or to non-adherence to our instructions given under "What

to do if there is a fault".

You should always give the data on the rating plate to your service centre in

case you have enquiries or want to order spare parts. The rating plate is lo-

cated underneath the cooking area.

Cleaning and care

[Never clean the glass ceramic hob with a steam cleaner or similar ap-

pliance!

■ Never use sharp or abrasive agents!

It is sufficient to clean with a damp

cloth and a little washing-up liquid

after usage. Wipe dry.

■ Incrustation due to boilied over foods

are best presoftened with a wet

cloth. Then remove them with a glass

scraper. Sugar and melted plastic

should be removed while the cooking

area is still hot.

■ Clean the glass-ceramic cooking area after every use. Always keep the sen-

sor keys clean, since soiling could be detected as finger contact by the

aplliance. Immediately remove soiling. Never put anything (pans, tea-towels

etc.) on the sensor keys! If food boils over onto the sensor buttons, we ad-

vise you to activate the emergency switch.

■ Care for your glass-ceramic cooking area once a week. Regular care builds

up a protective layer and also eases day to day cleaning. Please follow the

instructions of the cleaner or cleanser manufacturer concerned.

Even heavy soiling can be cleaned with a cleanser and enough water. Wipe

dry with a cloth.

Fault Cause Remedy

Thermal indicator of

cooking zone has

failed.

Lamp is defective. Call service centre. Risk of

burning, since no warning of

high temperatures.

Not possible to

switch off cooking

area.

Failure of electronic

component.

Switch off cooker fuse in fuse-

box,

Call service centre.

Cooking area does

not heat.

Fuse is defective. Check or replace cooker fuse in

fuse box.

Child proof lock

activated.

Deactivate child proof lock.

Cooking area is

defective.

Call service centre.

Inner circuit of the

dual-circuit zone is

defective.

Do not operate the functioning

outer circle.

Immediately call service centre.

Downloaded from www.Manualslib.com manuals search engine

EKE 805.3/606.3 21

* Figure only for cooking zones without an oven built-under the cook-

ing zone.

It must not be possible to remove the panel without using tools!

panel *

worktop

Deflector

plate

furniture

front

EKE 805.3

EKE 606.3

EKE 805.3

panel

EKE 606.3

worktop

Deflector

plate

furniture

front

Downloaded from www.Manualslib.com manuals search engine

22 EKE 805.3/606.3

Installation

Please note

KÜPPERSBUSCH built-in cooking zones may be combined only with KÜPPERS-

BUSCH built-in ovens with cooling fan. The use of any other make of oven

shall exempt Küppersbusch from all liability. Failure to observe this requi-

rement will invalidate all granted certificates and labels of approval.

Notes for fitting

■ The worktop must have a width of 40 mm. It is absolutely essential that the

worktop is aligned horizontally and that a clean cut is made into it!

■ The front, rear and lateral clearances around the hob unit must be main-

tained in accordance with the dimensional drawing.

A corner moulding of solid wood may be fitted to the worktop at the back

of the cooking area provided that the minimum clearances are maintained.

For practical reasons the lateral clearance between the appliance and an

adjacent tall cupboard unit must measure at least 300 mm.

■ Make sure that there is sufficient clearance underneath the cut-out. Any fur-

niture battens must be cut away to leave an area which is at least the same

size as the cut-out itself.

■ Make a point of ensuring that the plastic laminate or wood veneer on your

furniture surround has been applied by means of a heat-resistant adhesive

(100 °C).

■ Any cooker hoods or wall cupboards must have a vertical clearance of at

least 650 mm from the cooking area.

It will be expedient to seal built-in sinks and other built-in appliances in the

worktop in the same way (protection against ingress of water).

Prior to installation and after removal for repair, examine the gasket for pos-

sible damage. The gasket must provide perfect contact on all four sides. Re-

place it if necessary.

In the case of ceramic-tiled worktops it is necessary to provide an additional

seal with the aid of a permanently elastic sealing compound. Such sealing

compound can be purchased as Küppersbusch spare part No. 53 55 69.

– Clean the surfaces to be sealed in accordance with the manufacturer's

instructions on the cartridge. Apply the compound in a continuous strip,

pressing it firmly against the gap to be sealed.

– Cut away any surplus sealing compound with a sharp knife and clean the

sealed joint with water.

Installation of glass-ceramic cooking areas

First install the air deflector plate in the front of the work top cut- out

as shown.

An air gap of 5 mm is required between the worktop and the furniture front,

so that the hob can receive sufficient air. If the gap is less than 5 mm, the

top edge of the furniture front must be modified accordingly.

Using clips makes it easier and quicker for you to install these units. You can

carry out the complete installation work from above.

■ Always lift the cooking area by holding it at the sides. Do not lift it by the

front bar.

■ Be extremely careful when installing!

Do not place or drop any sharp or pointed tools (screwdrivers etc.) on the

glass surface!

■ The glass-ceramic cooking area must have a level and flush bearing. Any

distortion may lead to fracture of the glass panel.

– First of all make a clean cut into the worktop.

– Make sure that the gasket is properly seated. If the worktop surface is un-

even (tiles etc.), remove the gasket strip and seal with a heat resistant

sealing compound.

– Then insert the clips into the worktop cut-out as shown in the figures on

the previous page, observing the clearances indicated. It is not necessary

to adjust the height due to the horizontal stop motion device.

– Install the cooking area on the left as shown (1), align it (2) and fasten it (3).

If the worktop cut-out should be a little too

large, it is possible to increase the prelim-

inary spring tension of the clips by screw-

ing them down.

You only require the enclosed tension el-

ements S if you are fitting the cooking

area into worktops made of granite, mar-

ble or similar materials.

Electrical connection

■ The built-in cooking area must be connected to the mains supply by

a qualified electrician who is authorized to carry out such work.

■ Both legal wiring regulations and the requirements of your local electricity

supply board must be fully complied with.

■ Safeguard the appliance by means of line-protecting switches, fuses or con-

tactors with at least 3 mm contact opening width.

■ When connecting and repairing the appliance disconnect it from the elec-

tricity supply with one of these devices.

■ It must not be possible to touch nonconducting parts when the appliance is

installed.

■ The earthed conductor lead must be sufficiently long so that, in the event

of failure of the strain relief, it is not subjected to strain until after the live

wires of the connection cable.

■ Any superfluous cable must be removed from the installation area beneath

the appliance.

Electrical connection Permanent connection by means of an oven connec-

tion socket.

Connection diagram is depicted on the underside of the appliance, suita-

ble for the various types of mains.

Connection data Permanent connection 400 V 3 N

50 Hz

(AC 230 V in UK)

Voltage of heating element: 230 V

400 V 3 N ~ safety curren 16 A

400 V 2 N ~ safety curren 20 A

230 V 1 N ~ safety curren 25 A

230 V 3 ~ safety curren 16 A

Connection cable Use H 05 RR-F or H 07 RN-F.

The cable must be no shorter than 2 m.

Granite

Downloaded from www.Manualslib.com manuals search engine

Achtung!

Wichtiger Hinweis für Montage! Unbedingt beachten!

Das Luftleitblech (B) muß unbedingt vorne im Arbeitplattenausschnitt befestigt werden. Andernfalls kann

es während des Betriebes zu Schäden an der Elektronik kommen!

Attention!

Important installation instruction!

It is essential to attach the air deflector plate (B) at the front of the worktop opening, as otherwise damage

might be caused to the electronics of the hob during operation!

Attention!

Instruction d´installation importante!

La tôle de canalisation d'air (B) doit être obligatoirement fixée sur la face avant dans l'é videment du

plan de travail. Sinon les systèmes électroniques pourraient être endommagés pendant le fonctionne-

ment de la table de cuisson !

Opgelet!

Zeer voornaam! Voorzorg in acht te nemen

bij de montage van kookplaten EKE. De luchtgeleidingsplaat (B) moe t in elk ge val voora an in de uitsparing

van het aanrechtblad worden gemonteerd. Anders kan de elektronica van het kookveld bij het werken

beschadigd raken!

Attentione!

Instruzione d‘ installazione importante!

La lamiera di conduzione (B) deve essere assolutamente fissato al bordo frontale nel ritaglio del piano

di lavoro. Altrimenti durante un funzionamento potrebbe danneggiarsi l'elettronica del piano di cottura!

¡Atención!

¡Instrucción importante para el montaje!

¡Es indispensable fijar la chapa-guía del aire (B) en la parte delantera del hueco del tablero de trabajo.

De lo contrario, durante la cocción podrían producirse dete rioros del sistema electrónico de la encimera!

Atenção!

Indicação importante para a montagem! Observar sem falta!

A chapa de condução do ar (B) tem que ser impreterivelmente fixada à frente no entalhe do balcão de

serviço. Caso contrário, podem ser provocados danos na electrónica durante o funcionamento!

Observera!

Viktig information för montage! Beakta ovillkorligen!

Baffelplåten (B) måste ovillkorligen fästas framtill i arbetsbänkens urtag. I annat fall kan skador uppstå på den

elektroniska utrustningen under driften!

½

Ò{~{{Ó~

Ð{{(B)~{zz{z{{#Ë!

!{z{!{¨{

Aworktop

Bdeflector plate

Cfurniture front

Atable de travail

BTôle canalisant l´air

Cpanneau du meuble

Awerkblad

Bluchtgeleidingsplaat

Cmeubelpaneel

Apiano di lavoro

Blamiera di guida aria

Cfrontale del mobile

Atablero de trabajo

Bchapa guia del aire

Cfrontal del mueble

Aplano del trabalho

Bchapa de condução do ar

Cparte da frente do armário

AArbetsplatta

BCirculationsplat

CSnickerifront

Az{{

B{{

C

Wa.Nr.: 241087 L22

Downloaded from www.Manualslib.com manuals search engine

Küppersbusch EKE 606.3 Instructions For Use And Installation Instructions

Küppersbusch EKE 606.3 Instructions For Use And Installation Instructions

Küppersbusch EKE 606.3 Instructions For Use And Installation Instructions

Related papers

Other documents