CAME FROG Series Installation guide

Brand: CAME

Model: FROG Series

Category: Gate Opener

Type: Installation guide

This manual is also suitable for

Frog-A 24U

INSTALLATION MANUAL

FROG-A 24U

IN-GROUND OPERATOR FOR SWING GATES

FROG SERIES

Pag. 2 - Manual code: 119AV31 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

IMPORTANT UL-325 SAFETY INSTRUCTIONS

FROG-A24U

It is extremely important that all parties involved in the installation and operation of the gate operator system read and understand

the following warning instructions.

WARNING – To reduce the risk of injury or death:

1. READ AND FOLLOW ALL INSTRUCTIONS.

2. Never let children operate or play with gate controls. Keep the remote control away from children.

3. Always keep people and objects away from the gate. NO ONE SHOULD CROSS THE PATH OF THE MOVING GATE.

4. Test the gate operator monthly. The gate MUST reverse on contact with a rigid object or stop when an object activates

the non-contact sensors. After adjusting the force or the limit of travel, retest the gate operator. Failure to adjust and

retest the gate operator properly can increase the risk of injury or death.

5. Use the emergency release only when the gate is not moving.

6. KEEP GATES PROPERLY MAINTAINED. Read the installation manual and have a qualified service person make repairs

to gate hardware.

7. The entrance is for vehicles only. Pedestrians must use separate entrance.

8. SAVE THESE INSTRUCTIONS.

Instructions regarding intended installation of the gate operator.

A. Install the gate operator only when:

1. The operator is appropriate for the construction of the gate and the usage Class of the gate.

2. All openings of a horizontal slide gate are guarded or screened from the bottom of the gate to a minimum of

4 feet (1.22m) above the ground to prevent a 2-1/4 inch (57.2mm) diameter sphere from passing through the

openings anywhere in the gate, and in that portion of the adjacent fence that the gate covers in the open

position.

3. All exposed pinch points are eliminated or guarded.

4. Guarding is supplied for exposed rollers.

B. The operator is intended for installation only on gates for vehicles. Pedestrians must be supplied with a separate access

opening. The pedestrian access opening shall be designed to promote pedestrian usage. Locate the gate such that

persons will not come in contact with the vehicular gate during the entire path of travel of the vehicular gate.

C. The gate must be installed in a location so that enough clearance is supplied betweehbe employed, and adjacent

structures when openening and closing to reduce the risk of entrapment. Swinging gates shall not open into public access areas.

D. The gate must be properly installed and work freely in both directions prior to the installation of the gate operator.

Do not over-tighten the operator clutch or pressure relief valve to compensate for a damaged gate.

E. For gate operators utilizing Type D protection:

1. The gate operator controls must be placed so that the user has full view of the gate area when the gate is not

moving.

2. The placard provided marked in letters at least 1/4 - in (6.4mm) high with the word “WARNING” and the

following statement or equivalent: “Moving Gate Can Cause Serious Injury or Death” shall be placed adjancent

to the controls.

3. An automatic closing device (such as a timer, loop sensor, or similar device) shall not be employed.

4. No other activation device shall be connected.

Pag. 3 - Manual code: 119AV31 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

F. All openings of a horizontal slide gate are guarded or screened from the bottom of the gate to a minimum of 4 feet (1.22m)

above the ground to prevent a 2-1/4 inch (57.2mm) diameter sphere from passing through the openings anywhere in the gate,

and in that portion of the adjacent fence that the gate covers in the open position.

G. All exposed pinch points are eliminated or guarded.

H. The gate must be installed in a location so that enough clearance is supplied between the gate and adjacent

structures when opening and closing to reduce the risk of entrapment. Swinging gates shall not open into public access area.

I. Controls intended for user activation must be located at least six feet (6’) away from any moving part of the gate and

where the user is prevented from reaching over, under, around or through the gate to operate the controls. Outdoor or easily

accessible controls shall have a security feature to prevent unauthorized use.

K. FOR GATE OPERATORS UTILIZING A NON-CONTACT SENSOR:

1. See instructions on the placement of non-sontact sensors for each type of application.

2. Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle, trips the sensor while

the gate is still moving

3. One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists, such as

the perimeter reachable by a moving gate or barrier.

L. FOR A GATE OPERATOR UTILIZING A CONTACT SENSOR:

1. One or more contact sensors shall be located where the risk of entrapment or obstruction exists, such as the

leading edge, trailing edge, and post mounted both inside and outside of a vehicular horizontal slide gate.

2. One or more contact sensors shall be located at the bottom edge of a vehicular vertical lift gate.

3. One or more contact sensors shall be located at the pinch point of a vehicular vertical pivot gate.

4. A hardwired contact sensor shall be located and its wiring arranged so that the communication between the

sensor and the gate operator is not subjected to mechanical damage.

5. One or more contact sensors shall be located on the inside and outside leading edge of a swing gate.

Additionally, if the bottom edge of a swing gate is greater than 6 inches (152mm) above the ground at any

point in its arc of travel, one or more contact sensors shall be located on the bottom edge.

M. A minimum of two (2) WARNING SIGNS shall be installed, one on each side of the gate where easily visible.

a. Power should be disconnected before installing or servicing a gate operator.

b. All electrical wiring should comply with all local building and electrical codes.

c. All entrapment zones and pinching points should be covered.

d. All safety devices should be tested to assure their proper functionality.

e. The operation of the gate system: operator, controls and safety devices should be reviewed with the end user

or owner, who should be informed of the need for periodic maintenance of the safety and control equipment.

f. All installation operating and safety manuals should be left with the owner.

N. All gate operators systems should include safety devices such as reversing edges or photocells in order to provide

added protection. These safety devices should be installed in accordance to the design and application of the system

being installed.

O. A qualified professional installer should install a gate operator system, its safety accessories and should observe these

minimum procedures:

Pag. 4 - Manual code: 119AV31 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

CAME AMERICAS AUTOMATION, LLC

MANUFACTURER’S LIMITED 3-YEAR WARRANTY

Veriﬁcation of the warranty period requires copies of receipts or other proof of purchase.

Warranty cannot be honored without proof of purchase. Please retain these records.

Came Americas Automation, LLC (“CAME®”) products are warranted by CAME® against defects in materials and manufacturer

workmanship for a period of thirty-six (36) months from the date of purchase, provided the recommended installation manual and

procedure have been followed. CAME®’s sole obligation under this warranty is limited to repairing or replacing, at our option, any

parts which shall be determined by CAME® to be defective, and is conditioned upon CAME® receiving notice of any such defect

within the warranty period. Claims under this warranty may only be made by a purchaser of CAME® products (the “Customer”).

CAME® reserves the right to make the ﬁnal determination as to whether there is a defect in the materials and/or workmanship, and

whether or not a product is within the warranty period. CAME® is not responsible for any damages or other costs caused by, or which

may result from installation, handling, non-recommended operation, product abuse, or modiﬁcations not authorized by CAME® or for

any damages which may arise out of the use of CAME® products.

CAME® sells its products through authorized distributors. This warranty on CAME® products is NOT VALID if the products have been

purchased from an unauthorized distributor, reseller, online E-tailer ( e.g., E-bay®), or if a product serial number has been altered,

removed, or replaced in any way. To verify that you are buying from an authorized CAME distributor or reseller please

call +1 305-433-3307.

In the case of product failure due to defective material or manufacturer workmanship within the thirty-six (36) months warranty

period, the product will be repaired or replaced (at the manufacturer’s option) at no charge to the Customer, if returned, freight

prepaid, to CAME AMERICAS AUTOMATION, LLC, 11345 NW 122nd Street Medley, Florida 33178.

IMPORTANT: Obtain a Return Goods Authorization (RGA) number before returning item(s) to our facilities by submitting a warranty

claim and request for RGA with our customer service department. Products shipped without an RGA number will not be accepted.

Replacements or repaired parts are covered by this warranty for the remainder of the thirty-six (36) month warranty for the original

product or six (6) months from the date of repair or replacement, whichever is greater. CAME® will pay shipping costs at the ground

transport rate for the return to owner of item(s) repaired under warranty.

The manufacturer will not be responsible for any charges or damages incurred in the removal of the defective parts for repair, or the

reinstallation of these parts after repair. Use of any (00021996.doc V.2) components that are not CAME® speciﬁed (e.g. batteries, light

bulbs, drive belts, chains or transformers) will void the warranty. This warranty shall be void if damage to the product(s) was due to

improper installation or use, neglet, accident, use of non-CAME® speciﬁed or approved components or replacement parts, connection

to an improper power source, tampering, or if damage was caused by lighting, strikes, power surges, wind, ﬁre, ﬂoor, insects, or other

natural agents or disasters.

This warranty gives you specific legal rights, and you may also have other rights, which vary from

state to state (or jurisdiction to jurisdiction.) CAME's responsibility for malfunctions and defects in

equipment is limited to repair and replacement as set forth in this warranty statement.

THE CUSTOMER ACKNOWLEDGES AND AGREES THAT THIS WARRANTY IS MADE

EXPRESSLY IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES FOR THE

PRODUCT(S), INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES AND

CONDITIONS OF MERCHANTABLE QUALITY, MERCHANTABILITY, FITNESS FOR A

PARTICULAR PURPOSE, OR ANY OTHER EXPRESS OR IMPLIED WARRANTY ARISING

OUT OF LAW, STATUTE, USAGE OF TRADE OR COURSE OF DEALINGS.

The warranty hereunder is limited in time to the term of the limited warranty period reflected in this

limited warranty. No warranties, whether express or implied, will apply after the limited warranty

period has expired. Some states do not allow limitations on the term of an implied warranty, so this

limitation may not apply to you.

Pag. 5 - Manual code: 119AV31 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

CAME® DOES NOT ASSUME, AND SPECIFICALLY DISCLAIMS, ANY LIABILITY OR OBLIGATION WHATSOEVER IN THE SALE OF THE

PRODUCT(S), INCLUDING ANY LIABILITY FOR CONSEQUENTIAL, INCIDENTAL, PUNITIVE OR SPECIAL DAMAGES TO YOU OR ANY

OTHER PERSON OR ENTITY, INCLUDING, WITHOUT LIMITATION, ANY LIABILITY FOR THIRD-PARTY CLAIMS AGAINST YOU FOR

DAMAGES. THE CUSTOMER ACKNOWLEDGES THAT THIS LIMITED WARRANTY PROVIDED IN LIEU OF ALL OTHER WARRANTIES

AND CUSTOMER’S WAIVER OF SPECIAL, INCIDENTAL AND CONSEQUENTIAL DAMAGES IS COMMERCIALLY NECESSARY AND

REASONABLE, AN ESSENTIAL AND MATERIAL ELEMENT OF THIS TRANSACTION, AND UPON WHICH BOTH THE CUSTOMER AND

CAME® HAVE RELIED AND HAVE HAD THE OPPORTUNITY TO NEGOTIATE.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion

may not apply to you. CAME®‘s liability will be no more than the amount you paid for the product that is the subject of a claim.

This is the maximum amount recoverable under this warranty. The limitations in this section shall apply whether or not the

alleged breach or default is a breach of a fundamental or material condition or term,

or a fundamental or material breach.

CAME AUTOMATION GATES UL 325 CLASSES

CLASS DESCRIBTION DUTY CYCLE FROG-A24U

Residential Vehicular Gate Operator

Typical use: Home, 1-4 apartment condominium.

Limited public access.

Continuous X

Commerical/ General Access Vehicular Gate Operator

Typical use: Condominiums, hotels, parking lots.

No general public access.

Continuous X

III

Industrial/ Limited Access Vehicular Gate Operator

Typical use: industrial location, Factory, Loading Dock.

No general public access.

Continuous X

Restricted Access Vehicular Gate Operator

Typical use: Security area with restricted access.

No general public access.

Continuous X

Power Connection

CAUTION

Be sure that the circuit breaker for the line input power is turned off before connecting the input power to the unit.

Warning: CAME SPA is not responsible for researching and complying with local building codes. Be sure to check these

codes before installation.

The installer must use 14AWG conductors and ½” conduit for the power connection.

Pag. 6 - Manual code: 119AV31 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

4.1 Operator

4 Description

2.1 Intended use

1 Legend of symbols

This symbol tells you to read the section with particular care.

This symbol tells you that the sections concern safety issues.

This symbol tells you what to say to the end-users.

2 Condition of use

The FROG operator was engineered to power residential and condominium swing gates.

The use of this product for purposes other than those described above and installation executed in a manner

other than as instructed in this technical manual are prohibited.

3 Reference Standards

“IMPORTANT INSTALLATION, SAFETY INSTRUCTIONS”

“CAUTION: IMPROPER INSTALLATION MAY CAUSE SERIOUS DAMAGE, FOLLOW ALL INSTALLATION INSTRUCTIONS CAREFULLY”

“THIS MANUAL IS ONLY FOR PROFESSIONAL OR QUALIFIED INSTALLERS”

2.2 Limits to use

This product is engineered and manufactured by CAME CANCELLI AUTOMATICI S.p.a. and complies with current safety

regulations. The operator is made up of a foundation box, a release assembly, a gearmotor and a transmission arm.

Zinc-plated press-forged fondation box for underground installation. On the inside is the release assembly with a

customized, manual-release key and the gearmotor – made of a cast aluminium shell, inside of which operates an

irreversible, gear-ratio and, endless screw plus helical crown system. A transmission arm is connected to the gearmotor.

4.2 Technical features

Motor power supply: 24V D.C.

Max draw.: 15 A

Power: 1/4 Hp

Max Torque.: 320N

Opening time (90°): from 16 to 45 secs.

Gear ratio: 1/1152

Duty cycle: Intensive use

Protection rating: IP67

Weight: 25lbs

For intensive use and condominiums: max weight of the gate 880lbs with max length of 11.5ft.

For its quality processes management CAME cancelli automatici is ISO 9001:2000 certified, and for its environmental

management it is ISO 14001 certified. CAME engineers and manufactures all of its products in Italy.

This product complies with the following standards: UL325, and CSA C22.2 NO.247

131 F

-4 F

Pag. 7 - Manual code: 119AV31 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

4.3 Dimensions

Make sure you have all the tools and materials you will need for the installation at hand to work in total safety and

compliance with the current standards and regulations. The following figure illustrates the minimum equipment needed

by the installer.

5.2 Tools and materials

5 Installation

Before installing, do the following:

• Make sure you have a suitable omnipolar cut-off device with contacts more than 3 mm apart, and independent

(sectioned off) power supply.

• Make sure you have suitable tubing and conduits for the electrical cables to pass through and be protected against

mechanical damage.

• Fit tubing to drain away any water leaks which may cause oxidation

• Make sure that any connections inside the case (that provide continuance to the protective circuit) be fitted with

extra insulation as compared to the other conductive parts inside.

• Make sure the structure of the gate is sturdy, the hinges work and that there is no friction between moving and

non-moving parts.

• Make sure there is a mechanical stop for opening and closing.

Installation must be carried out by expert qualified personnel and in full compliance with current regulations.

5.1 Preliminary checks

16 13

6.2

2.3

2.6

(inches)

Pag. 8 - Manual code: 119AV31 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

4x1,5

3x1,5

120V

4x1

2x1,5

RG58

3x1

5x1

2x1

4x1

4x1,5

2x1

Note: If the cable length differs from that specified in the table, then you must determine the proper cable diameter in the

basis of the actual power draw by the connected devices and according to the local electrical code standards.

For connections that require several, sequential loads, the sizes given on the table must be re-evaluated based on actual

power draw and distances. When connecting products that are not described in this manual, please refer to the

instructions that come with said products.

5.3 Cable list and minimum thickness

Connections Type of cable

Length of cable 3 < 32ft Leng. cable 32 < 65ft Leng. cable 65 < 100ft

Control panel power supply 230V

UL LISTED

CABLE/WIRE

3G x 14AWG 3G x 14AWG 3G x 14AWG

Motor power supply 24V

3 x 20AWG 3 x 20AWG 3 x 20AWG

Flashing light

2 x 20AWG 2 x 20AWG 2 x 20AWG

Photocell transmitters

2 x 20AWG 2 x 20AWG 2 x 20AWG

Photocell receivers

4 x 18AWG 4 x 18AWG 4 x 18AWG

Accessories power supply

2 x 20AWG 2 x 20AWG 2 x 20AWG

Control and safety devices

2 x 20AWG 2 x 20AWG 2 x 20AWG

Antenna connection RG58

max. 32 ft

1) FROG unit

2) Control panel

3) Safety photocells

4) Radio receiver

5) Key-switch selector

6) Antenna

7) Command push-buthon panel

8) Flashing light

9) Photocell column

10) Shunt box

11) Transmitter

5.4 Standard installation

Pag. 9 - Manual code: 119AV31 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

5.5 Assembly diagram

Fig.3

2.64” in

2.6” in

6.3” in

4” in

2.4” in

.12” in

5.6 Installing the unit

- Check the eciency of both moving and non-moving parts on the structure that will be supporting the operator.

- Determine, depending on the type of supporting structure and desired opening, the exact position of the motor assembly

by following the standard applications shown.

- Set up a closing end stop and an opening end stop (g. 4, p. 5)

- Dig, depending on the size of the assembly, a foundation pit in the chosen spot (Fig. 3)

- Prepare a drainage system in the foundation, to drain away any water leaks which may cause oxidation (g 3 – part.1)

- The foundation box makes for quick and easy setting up of the assembly. Place it inside the pit with the pin aligned to

the upper hinge (Fig. 3 – part. 2), sink it into the cement (Fig. 3 – part. 3) making sure it is perfectly levelled and that the

upper edge is 1 inch above ground level (Fig. 3 part. 4)

- Plan for the route of the electrical cables according to the command and safety instructions using the apposite hole on

the box (Fig. 3 – part. 5)

- Grease the rotation pins of the foundation box and the gate attachment lever; the hinge and pin lever must be aligned

- Position the gate leaf between the upper hinge and the pin lever; the hinge and pin lever must be aligned

- Secure the pin lever to the gate leaf, by welding spots from 1 to 1.5 inches apart along the contact surface.

Avoid any welding near the threaded screws (Fig. 3 – Part. 6).

Fig.2

- Screw the M10 x 100 (A) and the M10 (B) bolt onto the

gearmotor arm as shown in g. 4-1 (left HAND installation)

and g. 4-2 (right HAND installation)

- Ax the gearmotor to the foundation box using the threaded

pins and securing it using the provided bolts and washers

- Insert the (C ) transmission lever between the motor arm

and the box lever and electronically shut the gate against

the closing end stop. Adjust screw (A) until it touches the (C)

transmission lever.

- When testing, adjust the screw so as to allow proper closing

pressure of the gate leaf and allow its re-hooking during the

mechanism’s release procedure.

- Once adjustment is complete, secure the (B) nut.

Fig.4

Fig.4-1

Fig.4-2

Pag. 10 - Manual code: 119AV31 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

5.7 Manual release

- In emergencies (i.e. power outages) the release mechanisms allow the gate to hook back up when closing.

- You may choose among three dierent release models: model A4366 with customised key (Fig. 5-A), model A4365 with

tri-lobed key and model A4364 with lever key (Fig. 5-B). We suggest greasing the release’s hook-up key (Fig. 5-B – part. 3)

consult the documentation pertinent to the relative items for the release procedure.

Note: Release operations need to be carried out during emergency procedures and with the power disconnected.

Fig. 5

Fig. 5-A

Fig. 5-B

A4366

A4364

A4365

- We suggest making the gearmotor cable connections in shunt boxes;

For further information concerning the functions, see the technical documentation for the ZLJ24U control panel.

6 Connecting to the control panel

ZLJ24U Control panel

26V

17V

230V

26V

17V

230V

L2TL1T L2TL1T

24 12 0 24 12 0

L N

+ -

E 10 11 TS E ES 1 2 3 4 5 CX CY

B1 B2S1

CZ7 2

FA2

GND

FC2FA1 FC1

+ -

M1 M2N1 N2

ENC1 ENC2

Connecting the 24V d.c. delayed closing gearmotor

120 V a.c.

power supply

BLUE

BLUE/BROWN

BROWN

Connecting the 24V d.c. delayed opening gearmotor

BLUE

BROWN

Pag. 11 - Manual code: 119AV31 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

6.1 Adjusting the brake microswitches

Fig. 7

– Using the motor, make so that the gate leaf is max 20 inches from being fully opened. At this point do a rst adjustment of

the (endstop) microswitches, positioning them close to the magnet. Consider that this type of endstop reads the magnetic

eld. You may have to repeat the procedure to increase the precision of the adjustment (g. 6/7)

1.2” in

2.4” in

6.2 Adjusting the limit stop’s stopping zone

Prepare a 2 x1 inch template and hold it up against one of the two mechanical stops as shown in g. 8 (adjustment is to be

made either on the closing endstop or opening endstop). Activate the gate - either using a command button or the remote

control - and turn the OP TIME (TL) trimmer clockwise until the gate leaf inverts its direction just as it touches the obstacle/

template. Then turn the template from its short side (g. 9) and check that the gate leaf stops against the obstable/template.

Otherwise activate the trimmer clockwise.

Fig. 8

Fig. 9

A =Eective range of the motion-inverter amperometric sensor.

B =Run zone at normal speed.

C =Run zone at slow speed.

D =Eective range of the motion-stop amperometric sensor

E =Opening/Closing position mechanical gate stops

2” in

20” in

Microswitch

Endstop

holding plate

Magnet

Microswitch

20” in.

Pag. 12 - Manual code: 119AV31 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

7 Safety instructions

This product must only be employed for its originally intended use. The automation using these gearmotors requires

adequate safety systems on the gate leaves to detect any obstacles (e.g. sensitive edges), in compliance with UL 325

standards and CSA C22.2 No. 247 or for both the US and Canada. Any other use is wrong and potentially dangerous.

The manufacturer cannot be held liable for any damages resulting from wrongful, erroneous or negligent uses.

Avoid working close to the hinges or other moving mechanical parts. Stay out of the opening/closing arc when operator is in

motion. Do not exercise force against the motion of the operator as this could result in potentially dangerous situations.

Do not allow children to play or loiter within the opening/closing arc of the operator.

Keep remote controls and any other command device out the reach of children, to prevent operator from being activated

by accident. In the event of anomalous behaviour, stop using the operator immediately.

Danger of crushing hands

Danger of crushing feet

Danger! High voltage

No transit during operation

Important safety instructions

Pag. 13 - Manual code: 119AV31 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

8 Maintenance

8.1 Periodic maintenance

Periodic maintenance to be carried out by the end-user is as follows: wipe clean the glass surface of the

photocells; check that the safety devices work properly; remove any obstructions. We suggest checking the state of

lubrication and tightness of the anchoring screws on the operator. To check the efficiency of the safety devices, move

an object in front of the photocells when gate is closing. If the operator inverts the motion or stops, the photocells are

working properly. This is the only maintenance procedure to be carried out with the power source connected. Before

performing any maintenance procedures, cut off the main power, to prevent possible accidents due to gate movement.

To clean the photocells use a water dampened cloth. Do not use solvents or other chemical products which may ruin

the devices. In the event of any strange vibrations or squeaking, lubricate the joints with grease, as shown in the

diagram.

Make sure there are no plants within the photocell’s beam, and that the gate motion is free of any obstacles.

8.2 Trouble shooting

MALFUNCTIONS POSSIBLE CAUSES CHECK AND REMEDIES

The gate will not open

nor close

• There is no power

• The gearmotor is released

• The remote control’s batteries are run down

• The transmitter is broken

• The stop button is either stuck or broken

• The opening/closing button or the key selector are stuck

• If not using EMERGENCY stop botton

• If not using PHOTOCELLS.

• Check that the power is up

• Call assistance

• Replace batteries

• Call assistance

• Jump between 2-1

• Jump N/C contacts if not used.

The gate opens but will

not close

• The photocells are engaged • Check that photocells are clean

and in good working order

• Call assistance

Pag. 14 - Manual code: 119AV31 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

8.3 Extraordinary maintenance

The following table serves to note down any extraordinary maintenance, repairs or improvements performed by

specialised firms.

Note: Any extraordinary maintenance must be performed by specialised technicians.

Extraordinary maintenance log

Date Notes

Signature

Periodic maintenance log (for end-user) (every 6 months)

Installer’s stamp Operator name

Date of job

Technician’s signature

Requester’s signature

Job performed_____________________________________________________________________________________

________________________________________________________________________________________________

Installer’s stamp Operator name

Date of job

Technician’s signature

Requester’s signature

Job performed_____________________________________________________________________________________

________________________________________________________________________________________________

Installer’s stamp Operator name

Date of job

Technician’s signature

Requester’s signature

Job performed_____________________________________________________________________________________

________________________________________________________________________________________________

Pag. 15 - Manual code: 119AV31 ver. 2.0 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

9 Demolition and disposal

Installer’s stamp Operator name

Date of job

Technician’s signature

Requester’s signature

Job performed_____________________________________________________________________________________

________________________________________________________________________________________________

Installer’s stamp Operator name

Date of job

Technician’s signature

Requester’s signature

Job performed_____________________________________________________________________________________

________________________________________________________________________________________________

In its premises, CAME cancelli automatici s.p.a. implements an Environmental Management System certified in

compliance with the UNI EN ISO 14001 standard to ensure environmental protection.

Please continue our efforts to protect the environment—which CAME considers one of the cardinal elements in the

developmentof its operational and market strategies—simply by observing brief recommendations as regards disposal:

DISPOSAL OF PACKAGING

The packaging components (cardboard, plastic, etc.) are all classifiable as solid urban waste products and may be disposed of

easily, keeping in mind recycling possibilities.

Prior to disposal, it is always advisable to check specific regulations in force in the place of installation.

PLEASE DISPOSE OF PROPERLY!

PRODUCT DISPOSAL

Our products are made up of various types of materials. Most of them (aluminium, plastics, iron, electrical wires, etc.) may

be disposed of in normal garbage collection bins and can be recycled by disposing of in specific recyclable material collection

bins and disposal in authorized centres.

Other components (electrical boards, remote control batteries, etc.), however, may contain polluting substances.

They should therefore be removed and given to qualified service companies for proper disposal.

Prior to disposal, it is always advisable to check specific regulations in force in the place of disposal.

PLEASE DISPOSE OF PROPERLY!

CAME Cancelli Automatici S.p.A.

via Martiri della Libertà, 15

31030 Dosson di Casier - Treviso - ITALY

tel (+39) 0422 4940 - fax (+39) 0422 4941

internet: www.came.it - e-mail: [email protected]

Intertek Testing Services NA Inc.

165 Main Street, Cortland, NY 13045

Telephone 800-345-3851 or 607-753-6711 Fax 607-756-6699

Standard for Door, Drapery, Gate, Louver, and Window Operators and Systems, UL 325 - 5th edition,

Issued 06/07/2002. Revised 08/29/2007.

Standard(s):

Standard for Operators and Systems of Doors, Gates, Draperies and Louvres, CSA C22.2 No. 247.

Issued 12/01/1992 (R2004), General Instruction No. 1

Product: Vehicular Horizontal Swing Gate Operators

Models: AXO Series: Models AX 5024U and AX 3024U

AMICO Series: Model A 1824U

FROG Series: Models A 24U and FROG JU

The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

CAME AMERICAS AUTOMATION, LLC

11345 NW 122nd STREET

MEDLEY FL 33178

Tel 305.433.3307

Fax 305.396.3331

The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.